Thermal Stability of Neodymium Aluminates High-[kappa] Dielectric Deposited by Liquid Injection MOCVD Using Single-Source Heterometallic Alkoxide Precursors

Abstract

Thin films of neodymium aluminate (NdAlO x ) have been deposited by liquid injection metalorganic chemical vapor deposition (MOCVD) using the bimetallic alkoxide precursor [NdAl(OPr i )6(Pr i OH)]2. The effects of high-temperature postdeposition annealing on NdAlO x thin films are reported. The as-deposited thin films are amorphous in nature. X-ray diffraction (XRD) and medium energy ion scattering (MEIS) show, respectively, no crystallization or interdiffusion of metal ions into the substrate after annealing at 950°C. The capacitance-voltage (C-V) and current-voltage (I-V) characteristics of the thin films exhibited good electrical integrity following annealing. The dielectric permittivity (κ) of the annealed NdAlO x was 12, and a density of interface states at flatband ( [subscript]Dit[/subscript] ) of 4.01×[superscript]1011[/superscript] cm-2 eV-1 was measured. The deposited NdAlO x thin films are shown to be able to endure high-temperature stress and capable of maintaining excellent dielectric properties.

P. Taechakumput 1 and C. Z. Zhao 1, 2 and S. Taylor 1 and M. Werner 3 and P. R. Chalker 3 and J. M. Gaskell 4 and H. C. Aspinall 4 and A. C. Jones 4 and Susu Chen 1

Recommended by Mohammad H. Maneshian

1, Department of Electrical Engineering and Electronics, University of Liverpool, Liverpool L69 3GJ, UK
2, Department of Electrical and Electronic Engineering, Xi'an Jiaotong-Liverpool University, Suzhou 215123, China
3, Department of Engineering, Materials Science and Engineering, University of Liverpool, Liverpool L69 3GH, UK
4, Department of Chemistry, University of Liverpool, Liverpool L69 3ZD, UK

Received 7 December 2011; Accepted 8 February 2012

1. Introduction

Recently, considerable effort has been exerted in developing high-κ rare earth oxide, M₂ O₃ (M = La, Pr, Nd, etc.), as a replacement of the conventional SiO₂ -based gate dielectric material [1]. The incorporation of neodymium (Nd) ions in insulating layers has important applications for solid-state laser materials, luminescent materials, protective coatings, and gate dielectric applications [2, 3]. However, Nd₂ O₃ is thermally unstable upon annealing and can be partially transformed to NdO(OH) when exposed to atmospheric conditions [4]. One of many solutions to enhance the thermal stability is the incorporation of aluminium (Al) to develop innovative multifunctional advanced lanthanide-aluminates-based ceramics, MAlO₃ (M = La, Pr, Gd, and Nd). The lanthanide aluminates are promising high-κ candidates as they combine the advantages of the high permittivity of the lanthanide oxide with the chemical and thermal stability of Al₂ O₃ . Furthermore, they remain amorphous up to high temperatures, leading to a large reduction in leakage current relative to polycrystalline M₂ O₃ films during CMOS processing [5, 6].

Work on NdAlO _x was mostly reported as a ceramic material for microwave applications and as a diffusion barrier in solid-oxide fuel cells [7, 8]. Growth of NdAlO _x thin films have previously been achieved by various deposition methods, including pulsed laser deposition [9], chemical vapor deposition [10, 11], e-beam evaporation [8], and atomic layer deposition [4]. To date, however, little is still known about the physical and electronic characteristics of NdAlO _x due to a lack of suitable precursors with appropriate stability, volatility, and decomposition characteristics. This has motivated us to further exploit these perovskite thin films for gate dielectric applications using an alternative single-source precursor. The use of single-source precursor allows better mixing of the components at atomic level, significantly lower decomposition temperature, and free from halide ions contamination [11].

In this work, the effects of high-temperature postdeposition annealing (PDA) on the properties of the NdAlO _x thin films, deposited by metalorganic chemical vapor deposition (MOCVD) using single-source precursor, were studied.

2. Experimental

Near stoichiometric NdAlO _x thin films (Nd/Al = 0.87) were deposited on n-type silicon (100) substrates by liquid injection MOCVD at 450°C on an Aixtron AIX 200FE AVD reactor fitted with the "TriJet"^TM liquid injector system [12], utilizing the single-source precursor [NdAl(OPr ⁱ )₆ (Pr ⁱ OH)]₂ . Selected films were subjected to high-temperature (750-950°C) postdeposition annealing (PDA) in pure nitrogen (N₂ ) ambient for 60 seconds. Subsequently, a postmetallization forming gas anneal (FGA) was carried out at 400°C for 30 minutes using H₂ : N₂ in the ratio 1 : 9, together with a control as-deposited sample.

X-ray diffraction (XRD) was performed on the studied films using nickel-filtered Cu Kα radiation ( λ = 1.5405 Å) with a 2θ increment of 0.2° per second. The samples were scanned over a θ /2θ range of 20° to 40°. Medium energy ion scattering (MEIS) experiments were carried out using a nominal 200 keV He⁺ ion beam and a 70.5° scattering angle. Cross-section transmission electron microscopy (TEM) was carried out using a JEOL 2000 FX operated at 500 kV. Capacitance-voltage (C-V ) measurements were conducted on the MOS capacitors of the structure (Au/NdAlO _x /SiO₂ /n-Si) using a HP4192 impedance analyzer, with 30 mV RMS probe signal, at various frequencies (1 kHz-1 MHz). Leakage current (I-V ) measurements were obtained using a Keithley K230 programmable voltage source and a 617 type electrometer.

3. Results and Discussion

Phase transitions of the gate dielectric, as a function of PDA temperatures, were accessed by X-ray diffraction (XRD). The X-ray diffraction traces of the as-deposited and PDA samples (regardless of PDA temperature) exhibited a diffraction peak consistent with the (200) peak from the silicon substrate. No other diffraction features were observed (Figure 1(a)), suggesting that they were essentially amorphous. In addition, MEIS results indicated that no significant level of crystallinity or movement of metal ions was in evidence in the 950°C PDA film as demonstrated in Figure 1(b).

(a) X-ray diffraction traces for NdAlO _x /SiO₂ stacks as a function of RTA temperatures. (b) A comparison of MEIS data of a NdAlO _x /SiO₂ stack prior to and after RTA in pure N₂ ambient for 1 min.

(a) [figure omitted; refer to PDF]

(b) [figure omitted; refer to PDF]

Figure 2 shows TEM micrographs in which the thicknesses of the high-κ stack, including the interfacial layer, were evaluated. The high-κ thickness and a thin native oxide interlayer, adjacent to the silicon substrate, changed from 11 nm and 1.5 nm, respectively, and to 10.4 nm and 2.5 nm respectively, after 950°C PDA. This could be due to inter-diffusion of oxygen between SiO₂ and NdAlO _x . The growth of the SiO₂ layer, following annealing, is also visible in the MEIS energy spectrum (Figure 1(b)). The amorphous nature of the thin films is also observed in the TEM analysis (Figure 2) confirming the XRD findings.

Figure 2: TEM image of the as-deposited and 950°C PDA NdAlO _x /SiO₂ stacks shows the thicknesses of oxide layers change from 1.5 nm/11 nm to 2.5 nm/10.4 nm, respectively.

[figure omitted; refer to PDF]

The high-frequency C-V characteristics of as-deposited and PDA samples are shown in Figure 3. Both as-deposited and PDA samples exhibited small counter-clockwise hysteresis (<0.1 V). A positive shift of flatband voltage ( _VFB ) (the shift of _VFB is 0.97 V) in the as-deposited sample was observed and contributed to fixed negative oxide charges. However, a near-ideal flatband voltage ( _VFB =0.65 V ) was obtained in the 950°C PDA sample. This may indicate that negative fixed oxide charges could be compensated by nitrogen-induced positive fixed oxide charges generated during annealing at the NdAlO _x /SiO₂ interface. Terman analysis [13] yields an interface density of states, _Dit , of 4.94×¹⁰¹¹ cm^-2 eV^-1 and 4.01×¹⁰¹¹ cm^-2 eV^-1 at midgap for as-deposited and 950°C PDA samples, respectively. This is lower than _Dit of other recent high-κ candidates, _Dit of 2.5×¹⁰¹² cm^-2 eV^-1 found in La_1.3 Hf_1.0 O_4.1 [14], but higher than the interface state density of 5×¹⁰¹⁰ cm^-2 eV^-1 shown by Y _x Hf_1-x O_y (x = 0.065) [15].

Figure 3: A comparison of high-frequency C-V curves with and without N₂ PDA treatment. MOSCs with [Au/NdAlO _x /SiO₂ /n-Si/Al] structure were fabricated with an effective area of 4.9 × 10^-4 cm^-2 . The inset is a plot of capacitance equivalent thickness (CET) versus NdAlO _x physical thickness, which shows an increase in the dielectric permittivity (7 to 12) and changes of the interfacial layer (1.5 to 2.5 nm) after PDA treatment.

[figure omitted; refer to PDF]

Despite an increase of the interfacial layer in the PDA samples, the measured capacitance in strong accumulation was found to be higher than that of the as-deposited samples. The inset of Figure 3 shows a plot of the high-κ dielectric thickness against capacitance equivalent thickness (CET). The slope revealed the NdAlO _x dielectric permittivity (κ ) to be 7 and 12 in the as-deposited and 950°C PDA films, respectively. The increase of dielectric permittivity (κ ), observed after receiving thermal treatment, could be due to a small change of the crystal symmetry, with the formation of some small nanometer scale crystallites with higher permittivity phases of NdAlO _x [16, 17].

The leakage current densities ( J ) at 2 MV cm^-1 in all samples, even after 950°C PDA, were below 1×^10-7 A cm^-2 (Figure 4), which is comparable with other leading edge high-κ dielectrics [18]. The average breakdown, regardless the annealing treatment, also occurs at the equivalent field strength of 7 MV cm^-1 .

Figure 4: Leakage current density ( J ) versus electric field (Eox) applied across the NdAlO _x /SiO₂ stacks as a function of PDA temperatures. The NdAlO _x films thickness was _thigh-κ ~ 10.4 to 11 nm.

[figure omitted; refer to PDF]

4. Conclusions

The NdAlO _x thin films deposited by liquid injection MOCVD have been shown to remain amorphous up to 950°C as shown by XRD analysis. No significant level of crystallinity or movements of metal ions was also in evidence after annealing at 950°C as indicated in MEIS energy spectra. Electrical properties of NdAlO _x samples, after high-temperature annealing, were presented. Good electrical integrity was maintained even after 950°C PDA as shown by C-V and I-V results, showing the extracted dielectric permittivity of 12, a low leakage density of 7×^10-7 A cm^-2 at 2 MV cm^-1 , and a density of interface states at flatband _Dit of 4.01×¹⁰¹¹ cm^-2 eV^-1 . These features make the neodymium aluminate a potential candidate for the dielectric replacement.

Acknowledgments

This research was funded in part by the Engineering and Physical Science Research Council of UK under Grants nos. EP/D068606/1 and GR/S76632/01, from the National Natural and Science Foundation of China under the Grant no. 60976075, and from the Suzhou Science and Technology Bureau of China under the Grant no. SYG201007. Special appreciation is extended to Mr. Kevin Molloy for technical assistance with sample metallization, Dr. N. Pham for XRD measurements, and Mr. R. T. Murray for TEM measurements.

References

[1] M. Leskelä, M. Ritala, "Rare-earth oxide thin films as gate oxides in MOSFET transistors," Journal of Solid State Chemistry , vol. 171, no. 1-2, pp. 170-174, 2003.

[2] G. Bonnet, M. Lachkar, J. C. Colson, J. P. Larpin, "Characterization of thin solid films of rare earth oxides formed by the metallo-organic chemical vapour deposition technique, for high temperature corrosion applications," Thin Solid Films , vol. 261, no. 1-2, pp. 31-36, 1995.

[3] S. Chevalier, G. Bonnet, J. P. Larpin, "Metal-Organic Chemical Vapor Deposition of Cr2O3 and Nd2O3 coatings. Oxide growth kinetics and characterization," Applied Surface Science , vol. 167, no. 3, pp. 125-133, 2000.

[4] A. Kosola, J. Päiväsaari, M. Putkonen, L. Niinistö, "Neodymium oxide and neodymium aluminate thin films by atomic layer deposition," Thin Solid Films , vol. 479, no. 1-2, pp. 152-159, 2005.

[5] J. M. Gaskell, A. C. Jones, H. C. Aspinall, S. Przybylak, P. R. Chalker, K. Black, H. O. Davies, P. Taechakumput, S. Taylor, G. W. Critchlow, "Liquid injection ALD and MOCVD of lanthanum aluminate using a bimetallic alkoxide precursor," Journal of Materials Chemistry , vol. 16, no. 39, pp. 3854-3860, 2006.

[6] M. Nieminen, T. Sajavaara, E. Rauhala, M. Putkonen, L. Niinistö, "Surface-controlled growth of LaAlO3 thin films by atomic layer epitaxy," Journal of Materials Chemistry , vol. 11, no. 9, pp. 2340-2345, 2001.

[7] E. A. Nenasheva, L. P. Mudroliubova, N. F. Kartenko, "Microwave dielectric properties of ceramics based on CaTiO3-LnMO3 System (Ln-La, Nd; M-Al, Ga)," Journal of the European Ceramic Society , vol. 23, no. 14, pp. 2443-2448, 2003.

[8] C. Brugnoni, U. Ducati, C. Chemelli, M. Scagliotti, G. Chiodelli, "SOFC cathode/electrolyte interfaces. Part II: study of NdAlO₃ diffusion barriers," Solid State Ionics , vol. 76, no. 3-4, pp. 183-188, 1995.

[9] M. Henini, "High quality YBa₂ Cu₃ O_7-x /NdAlO₃ /YBa₂ Cu3O_7-x trilayers on (100) MgO for microwave applications," Thin Solid Films , vol. 306, no. 1, pp. 141-146, 1997.

[10] S. Mathur, M. Veith, H. Shen, N. Lecerf, S. Hüfner, "Effect of Al2O3 matrix on the optical properties of NdAlO3 in NdAlO3/Al2O3 ceramic-ceramic composite," Scripta Materialia , vol. 44, no. 8-9, pp. 2105-2109, 2001.

[11] M. Veith, S. Mathur, N. Lecerf, K. Bartz, M. Heintz, V. Huch, "Synthesis of a NdAlO3/Al2O3 ceramic-ceramic composite by single-source precursor CVD," Chemistry of Materials , vol. 12, no. 2, pp. 271-274, 2000.

[12] J. M. Gaskell, S. Przybylak, A. C. Jones, H. C. Aspinall, P. R. Chalker, K. Black, R. J. Potter, P. Taechakumput, S. Taylor, "Deposition of Pr- and Nd-aluminate by liquid injection MOCVD and ALD using single-source heterometallic alkoxide precursors," Chemistry of Materials , vol. 19, no. 19, pp. 4796-4803, 2007.

[13] L. M. Terman, "An investigation of surface states at a silicon/silicon oxide interface employing metal-oxide-silicon diodes," Solid State Electronics , vol. 5, no. 5, pp. 285-299, 1962.

[14] Y. F. Loo, S. Taylor, R. T. Murray, A. C. Jones, P. R. Chalker, "Structural and electrical characterization of amorphous lanthanum hafnium oxide thin films," Journal of Applied Physics , vol. 99, no. 10, 2006.

[15] E. Rauwel, C. Dubourdieu, B. Holländer, N. Rochat, F. Ducroquet, M. D. Rossell, G. Van Tendeloo, B. Pelissier, "Stabilization of the cubic phase of HfO2 by y addition in films grown by metal organic chemical vapor deposition," Applied Physics Letters , vol. 89, no. 1, 2006.

[16] S. Govindarajan, T. S. Boscke, P. Sivasubramani, "Higher permittivity rare earth doped HfO₂ for sub-45-nm metal-insulator-semiconductor devices," Applied Physics Letters , vol. 91, no. 6, 2007.

[17] T. S. Boscke, S. Govindarajan, P. D. Kirsch, "Stabilization of higher-κ tetragonal HfO₂ by SiO₂ admixture enabling thermally stable metal-insulator-metal capacitors," Applied Physics Letters , vol. 91, no. 7, 2007.

[18] C. Vahlas, "Cyclic atomic layer deposition of hafnium aluminate thin films using tetrakis(diethylamido)hafnium, trimethyl aluminum, and water," Chemical Vapor Deposition , vol. 12, no. 2-3, pp. 125-129, 2006.