Surface-passivated GaAsP single-nanowire solar cells exceeding 10% efficiency grown on silicon

Abstract

Continued development of high-efficiency multi-junction solar cells requires growth of lattice-mismatched materials. Today, the need for lattice matching both restricts the bandgap combinations available for multi-junctions solar cells and prohibits monolithic integration of high-efficiency III-V materials with low-cost silicon solar cells. The use of III-V nanowires is the only known method for circumventing this lattice-matching constraint, and therefore it is necessary to develop growth of nanowires with bandgaps >1.4 eV. Here we present the first gold-free gallium arsenide phosphide nanowires grown on silicon by means of direct epitaxial growth. We demonstrate that their bandgap can be controlled during growth and fabricate core-shell nanowire solar cells. We further demonstrate that surface passivation is of crucial importance to reach high efficiencies, and present a record efficiency of 10.2% for a core-shell single-nanowire solar cell.

ARTICLE

Received 29 Nov 2012 | Accepted 17 Jan 2013 | Published 19 Feb 2013

Continued development of high-efciency multi-junction solar cells requires growth of lattice-mismatched materials. Today, the need for lattice matching both restricts the bandgap combinations available for multi-junctions solar cells and prohibits monolithic integration of high-efciency III-V materials with low-cost silicon solar cells. The use of III-V nanowires is the only known method for circumventing this lattice-matching constraint, and therefore it is necessary to develop growth of nanowires with bandgaps 41.4 eV. Here we present the rst gold-free gallium arsenide phosphide nanowires grown on silicon by means of direct epitaxial growth. We demonstrate that their bandgap can be controlled during growth and fabricate core-shell nanowire solar cells. We further demonstrate that surface passivation is of crucial importance to reach high efciencies, and present a record efciency of 10.2% for a core-shell single-nanowire solar cell.

DOI: 10.1038/ncomms2510

Surface-passivated GaAsP single-nanowire solar cells exceeding 10% efciency grown on silicon

Jeppe V. Holm1,*, Henrik I. Jrgensen1,*, Peter Krogstrup2, Jesper Nygrd2,3, Huiyun Liu4 & Martin Aagesen1,*

1 SunFlake A/S, Universitetsparken 5, Copenhagen DK-2100, Denmark. 2 Nano-Science Center, Niels Bohr Institute, University of Copenhagen, Universitetsparken 5, Copenhagen, DK-2100, Denmark. 3 Center for Quantum Devices, Niels Bohr Institute, University of Copenhagen, Universitetsparken 5, Copenhagen DK-2100, Denmark. 4 Department of Electronic and Electrical Engineering, University College London, London WC1E 7JE, UK. * These authors contributed equally to this work. Correspondence and requests for materials should be addressed to M.A. mailto:(email: [email protected])

Web End =(email: [email protected]).

NATURE COMMUNICATIONS | 4:1498 | DOI: 10.1038/ncomms2510 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications 1

& 2013 Macmillan Publishers Limited. All rights reserved.

ARTICLE NATURE COMMUNICATIONS | DOI: 10.1038/ncomms2510

Improving the cost/efciency ratio of III-V-based multi-junction cells can be done through efciency enhancements, by adding additional junctions to the cell stack1 or through the

lowering of cost by replacing the expensive germanium substrate with silicon. Integrating III-V semiconductors and silicon requires overcoming their differences in lattice parameters and thermal expansion coefcient, as well as their polar/non-polar interfaces2,3. When constrained to a silicon-bottom cell, the optimum dual-junction solar cell, the simplest multi-junction solar cell, has a theoretical 1-sun peak efciency between 33 and 43% (refs 4,5) when combined with a 1.7 eV bandgap top cell; this can be achieved with a III-V semiconductor consisting of GaAs0.8P0.2.

The small contact interface between the nanowire and the silicon substrate ensures that strain from lattice mismatch is relaxed within the rst few monolayers6. Using the method of gallium (Ga)-assisted growth, gold-free perfect single crystal, gallium arsenide (GaAs) nanowires have been grown directly on silicon7. Higher bandgap gallium phosphide (GaP)8 and gallium arsenide phosphide (GaAsP)9,10 nanowires have also been grown, but only using gold as growth catalyst. Gold is incompatible with silicon11, and has been shown to incorporate into the III-V crystal12 and degrade the optoelectronic properties of the nanowires13. In addition, a sparse array of nanowires can absorb almost all incoming light14, meaning that only minute amounts of the expensive III-V material is needed for making a nanowire top cell. Devices consisting of a contacted ensemble of free-standing nano-wires have been exposed to temperature changes of up to 200 K, demonstrating that their strain-relieving ability is able to overcome the difference in thermal expansion15. To fully utilize their advantage with regards to non-lattice-matched growth, the nanowires themselves must also be able to function well as solar cells.

ResultsGa-assisted GaAs0.8P0.2 nanowire growth. High-quality GaAsP nanowires were grown without the use of a buffer layer on epi-ready Si(111) substrates having a native oxide surface layer. Solid-source molecular beam epitaxy (MBE) was used for the growths. The Ga-assisted vapourliquidsolid growth method demonstrated

with GaAs nanowires7,16 was adapted to allow for the difference in nucleation energy caused by the addition of P to the growth environment. Direct substitution of an As beam ux with a similar P beam equivalent pressure, resulted in a high nucleation rate that caused the Ga droplet to disappear. By lowering the V/III ux ratio, the nucleation rate was decreased and the Ga droplet maintained throughout the nanowire growth (Fig. 1a,b). The growth parameters: V/III ux ratio, P/As ux ratio and temperature, yielding the highest crystal quality, were determined by inspecting the wires using transmission electron microscopy (Fig. 1b and Supplementary Figs S1S3). The different diffusion lengths and incorporation rates of P and As, in combination with the changing growth landscape, mean that the P/As ux ratio needs to be adjusted throughout the growth (Fig. 1c). We were able to grow nanowires with constant P content as well as graded nanowires with P content varied from x 0.15 to x 0.70 (GaAs1

xPx) along

the wire axis (Supplementary Fig. S4). With a systematic focus on the growth parameters, Ga-assisted GaAs0.8P0.2 nanowires with a1.7 eV bandgap consisting of a close to perfect zinc-blende crystal were successfully produced. The bandgap of nanowire ensembles was determined using room temperature photoluminescence (PL) and further veried on individual nanowires by energy-dispersive X-ray spectroscopy (Supplementary Figs S4 and S5).

Core-shell nanowire solar-cell fabrication. Solar-cell structures were made by fabricating pin core-shell GaAsP nanowires. The core-shell pin-junction growth method allows for the design of optimal doping densities and layer thicknesses. Further, the radial pin junction ensures a sufcient optical absorption length while minimizing the carrier-extraction distance. First, a p-type core nanowire was grown by introducing beryllium during the axial vapourliquidsolid growth. A Ga-free step was added to let the group V material consume the Ga droplets and halt further axial growth. Then, two GaAsP shells were grown around the As-grown nanowires, using vapoursolid (VS) epitaxial growth, the rst one intrinsic and the second one n-type by doping with silicon. Before the radial shell growth, the substrate temperature was lowered to avoid beryllium diffusion and to enhance n-type

30

Phosphorus

content (x)

25

20

15

10

5

0 0 1 2 3 4 5 6 7

Distance from bottom of wire (m)

Figure 1 | Ga-assisted GaAs1 xPx nanowires grown directly on silicon. (a) Scanning electron microscope image of GaAsP nanowires, each having

a Ga droplet on top. The nanowires are seen from above at an angle of 25. Scale bar, 1 mm. (b) Transmission electron microscope image showing the upper part of a GaAsP nanowire with only a few twinnings visible just below the Ga droplet and further down the nanowire. Scale bar, 200 nm. Inset: diffraction image showing the nanowires zinc-blende crystal structure, expanded in Supplementary Fig. S3. (c) Energy-dispersive X-ray spectroscopy characterization of P content (x-value) in two nanowires from the same growth. The variation in P during the rst 1 mm of the growth is due to a deliberate ux change, whereas the downward slope is under a constant ux.

2 NATURE COMMUNICATIONS | 4:1498 | DOI: 10.1038/ncomms2510 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications

& 2013 Macmillan Publishers Limited. All rights reserved.

NATURE COMMUNICATIONS | DOI: 10.1038/ncomms2510 ARTICLE

R19 R20

R22

R21

Si(111)

Intensity

107

106

105

104

103

102 27.5

28.0

28.5

2 (o)

Si(111)

107

106

105

104

103

102

R29 no passivation

R30 passivated

Intensity

27.5 28.5

28.0

2 (o)

Figure 2 | Lattice matching of the GaAs1-xPx shell using X-ray diffraction. (a) A GaAsP core-shell growth series consisting of four growths with identical core growth parameters. The series was aligned using the sharp Si(111) peak from the substrate. The peaks to the left are from the nanowire crystal, and any shift or broadening of the peaks towards the right represents a shift in lattice size towards a higher P content. (b) Two GaAsP core-shell growths with the only difference being the addition of an InGaP passivation layer to R30. The unpassivated and passivated SNWSCs were fabricated using nanowires from these two growths. (c) Scanning electron microscope image of a core-shell GaAsP nanowire from the same growth as the best device. Scale bar, 1 mm.

doping of the silicon. As and P have different incorporation rates during planer (VS) lm growth, and these rates further depend on beam uxes and growth temperature. To grow a lattice-matched shell around the core nanowire, a series of core-shell growths were carried out to optimize the growth parameters. The growths were characterized using X-ray diffraction, which shows mismatched lattice sizes as multiple peaks in the data plot. For the ideal core-shell nanowire growth, only two peaks should be visible, one from the silicon crystal lattice in the substrate and one from the GaAsP core-shell nanowire. The rst growth (R19) in the series had a too high P content in the shell (Fig. 2a). The nal growth (R22) in the series showed only one III-V peak, indicating a lattice-matched core and shell. The GaAs0.8P0.2 (111) peak should yield a 2YE27.5, which correlates well with the R22 growth.

Single-nanowire solar cell (SNWSC) characterization. To produce SNWSCs, the nanowires were removed from the growth substrate, placed on an oxide covered silicon substrate and contacted at both ends (see Fig. 3c and Methods for details on the fabrication scheme). The SNWSCs were characterized individually by measuring current-voltage curves in the dark and under

AM1.5G illumination. The best unpassivated SNWSC had an efciency of 6.8%, short circuit current ISC 13.2 mA cm 2,

open circuit voltage VOC 0.76 V and ll factor (FF) 0.68

(Fig. 3a). This efciency is higher than what has previously been reported1719, but still considerably lower than the theoretical ShockleyQueisser limit, which for a 1.7 eV bandgap is 29%, ISCB23 mA cm 2, VOCB1.4 V and FFB0.9 (ref. 20). For a device geometry similar to ours, it is predicted that roughly half of the projected sunlight is absorbed21, which accounts well for the discrepancy between measured and ShockleyQueisser ISC. The

measured VOC is also about half of the ShockleyQueisser limit, but this cannot be accounted for by the low absorption in this solar-cell geometry. A low VOC is often attributed to non-optimal doping of the n- and p-region or inadequate surface passivation.

Surface passivation. Because nanowire solar cells have a high surface to volume ratio compared with planar solar cells, it is critical to passivate the surface of the wires, that is, stopping charge carriers from reaching the surface and recombining at surface states. Simulations on InP core-shell nanowires predicted a 32% improvement in efciency when reducing the surface recombination22. By growing an additional shell of B10 nm highly n-doped InGaP, we have for the rst time applied surface passivation to III-V nanowire solar cells (Fig. 2b,c). The clear faceting in Fig. 2c is a signature of a highly crystalline core-shell growth. Using the passivated nanowires, SNWSCs similar to the unpassivated ones were fabricated. Because the rate of surface recombination typically increases rapidly with bias, introducing a surface-passivation layer should give a large increase in VOC and

only a small increase in ISC, which is precisely what we observe (Fig. 3b). Another typical sign of a high recombination rate is a low FF and a high ideality factor. The passivation layer increased the ll-factor from 0.68 to 0.77 and decreased the ideality factor from 2.2 to 2.0, indicating that we indeed have lowered the rate of surface recombination (Table 1). With the introduction of a passivation layer, we have been able to signicantly increase the peak efciency to 410% and the average efciency by 72%

(Fig. 3d,e). Characterization as a function of laser wavelength further conrms a 1.7-eV bandgap, because the external quantum efciency is zero below the bandgap of the nanowire and increases sharply around 1.7 eV (Fig. 3f).

DiscussionOur realization of GaAsP semiconductor structures directly on silicon, and the excellent performance of the SNWSCs, demonstrates essential steps towards a robust high-efciency and low-cost dual-junction solar cell. Furthermore, this record SNWSC efciency has been achieved despite the less than optimal bandgap of GaAsP as a single-junction cell. We still need to optimize the individual nanowires to reach efciencies close to the ShockleyQueisser limit. We have here demonstrated the rst attempt on optimizing the open circuit voltage and FF by means of surface passivation, but have yet to focus on doping concentrations and layer thicknesses in the pin junction. There are additional challenges towards a dual-junction nanowire/ planar solar cell. For homogeneous growth and light management, the nanowires should be grown in a positioned array23and contacted24. The nanowire array must furthermore be produced without any parasitic bulk growth between the nanowires, which will function as Shockley Read Hall recombination centres. The array must be grown on a (111) silicon solar cell, and a tunnel junction must be implemented between the two junctions. The GaAsP/Si dual-junction solar cell is only one example of how nanowires can be used to produce more cost-efcient multi-junction solar cells in the future. The inherent ability of

NATURE COMMUNICATIONS | 4:1498 | DOI: 10.1038/ncomms2510 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications 3

& 2013 Macmillan Publishers Limited. All rights reserved.

ARTICLE NATURE COMMUNICATIONS | DOI: 10.1038/ncomms2510

15

15

60

150

10

40

10

100

Current (mA cm2)

Current (pA)

Current (mA cm2)

5

20

5

50

0

0

Current (pA)

0 0.0 0.2 0.4 0.6 0.8 1.0

15

0.2

0.2 0.0

0 0.2 0.4 0.6 0.8 1.0

5

Voltage (V)

20

5

Voltage (V)

50

10

40

10

100

60

150

Wavelength (nm)

Photon energy (eV)

16

50 700 750 800

10

Power (mW cm2)

Number of solar cells

14

12

40

1 mW cm2

10

30

2 mW cm2

0.5 mW cm20.25 mW cm20.1 mW cm2

5

8

EQE (%)

6

20

4

2

10

0 0.0 0.2 0.4 0.6 0.8 1.0

0 0 1 2 3 4 5 6 7 8 9 10 11 12

0

Voltage (V)

Efficiency (%) 1.8 1.7 1.6 1.5

Figure 3 | Characterization of SNWSCs with and without passivation. (a,b) I-V characteristics under dark (blue dots) and AM1.5G illuminated conditions (red dots) of (a) the unpassivated and (b) passivated SNWSCs with the highest efciency. The black line is a t to the data. Passivation increased the efciency by 50%. (c) A scanning electron microscope image of the best passivated device. Scale bar, 1 mm. (d) PV comparison between the best passivated (Pmax 10.2 mWcm 2) (red) and unpassivated (Pmax 6.8 mWcm 2) (blue) SNWSC. (e) Histogram of the 1-sun efciency of 28

unpassivated (blue) and 43 passivated (red) SNWSCs. The Lorentzian t shows that the passivation has increased the average efciency by 72% (5.0% for the passivated versus 2.9% for the unpassivated). (f) External quantum efciency (EQE) versus photon energy of the SNWSC in b,c.

Table 1 | Key performance parameters of the three best passivated and unpassivated SNWSCs

Passivated Unpassivated1 2 3 1 2 3 Efciency (%) 10.2 8.2 7.6 6.8 6.4 5.0

ISC (mA cm 2) 14.7 14.2 11.9 13.2 13.8 14.3 VOC (V) 0.9 0.8 0.88 0.76 0.74 0.64 FF 0.77 0.72 0.72 0.68 0.62 0.55 Ideality factor 2.0 2.2 2.2 2.2 2.6 2.7

nanowires to relieve strain while conserving crystal quality means that lattice matching between two or more of the solar-cell junctions can be relaxed, thereby allowing for new and better bandgap combinations to be used. Our growth method should enable growth of nanowires in the full 1.422.26 eV GaAsP bandgap range, which could facilitate their use as both the top junction in a III-V on Si dual-junction solar cell and a fourth junction in a four-junction solar cell.

In conclusion, we have demonstrated high-quality gold-free GaAsP nanowires, grown directly on silicon, with an optimum bandgap for use in a dual-junction silicon-based solar cell. The nanowires have intrinsic properties that overcome the requirements for lattice matching, as well as the difference in thermal expansion coefcient and polar/non-polar interface, which until now have hampered III-V on silicon growth. A surface-passivated GaAsP SNWSC has achieved a 1-sun record efciency of 10.2%, which effectively doubles the previous SNWSC record1719.

Methods

Crystal growth. The GaAsP core-shell nanowires were fabricated using solid-source III-V MBE. Substrates of 380-mm thick B-doped Si(111) with a thin layer of native oxide were used in the experiments. To enhance the reproducibility between growths, the substrates were rst heated to 1100 C in the MBE system to remove the existing layer of surface oxide, and afterwards kept for 24 h in the clean room before being re-loaded into the MBE system. Using the method of Ga-assisted growth, the core nanowires were grown by means of a Ga droplet that formed on the silicon surface during the rst few seconds of the growth procedure.

The core-nanowire growths were carried out at a substrate temperature ranging between 620 and 650 C measured using a pyrometer. For the core growth series, the Ga ux was varied between the growths but kept within the range of 4 10 8

9 10 8 torr. The group V ux was also varied between growths but was within

the range of 2.8 10 67.0 10 6 torr. Core-nanowire growth times were up to

1 h. Following core-nanowire growth, the Ga shutter was closed to interrupt axial growth. During the 1020 min growth interrupt, the Ga droplets were consumed by the group V uxes, and the temperature was lowered to 460470 C where shell growth was carried out. For p-type doping of the core, a Be doping density corresponding to 8 1017 cm 3 for planar growth of GaAs at 1 ML s 1 was used,

and for the n-type shell growth, a silicon doping density corresponding to0.8 10181.3 1018 cm 3 for planar growth at 1 ML s 1 was used.

Device fabrication. The wires were removed from the growth substrate by sonication in isopropanol and drip dried onto strongly p-doped Si(100) substrates covered with 500 nm thermal SiO2 and pre-fabricated alignment marks. The contact to the p-doped core was dening using e-beam lithography followed bya 4560 s etch at 30 C in H3PO4:H2O2:H2O (1:1:15) to expose the core and subsequent thermal evaporation of 5 nm Au/30 nm Zn/150 nm Au. The p-contact was annealed for 2 min at 420 C in a N2 atmosphere. Contact to the n-doped wire surface was dened using e-beam lithography followed by a 20 s B-HF etch to remove oxide and a quick load into the evaporation chamber. Several n-contacts have been tested. The results in this article have been achieved with unannealed 40 nm Ge/60 nm Au/27 nm Ni/200 nm Au, annealed 100 nm Ge/100 nm Au for2 min at 300 C in a N2 atmosphere and annealed 6 nm In/240 nm Au-Ge eutectic for 2 min at 300 C in a N2 atmosphere. Contact pads were dened using ultraviolet lithography and consist of e-beam evaporated 10 nm Ti/150 nm Au.

Optical characterization. Solar illumination was done with a standard solar simulator (LOTOriel 150 W Xe lamp) with a 10 beam diameter and an AM1.5G lter. The 1-sun intensity was veried using a mono-crystalline silicon solar cell calibrated at Radboud University Nijmegen against a National Renewable Energy Laboratory (NREL) secondary cell standard.

For the quantum efciency measurements, a continuous wave titanium sapphire laser, tuneable from 700 to 1000 nm, was used.

References

1. King, R. R. et al. Solar cell generations over 40% efciency. Prog. Photovoltaics Res. Appl. 20, 801815 (2012).

2. Fang, S. F. et al. Gallium arsenide and other compound semiconductors on silicon. J. Appl. Phys. 68, R31 (1990).

3. Moutanabbir, O. & Gsele, U. Heterogeneous integration of compound semiconductors. Ann. Rev. Mater. Res. 40, 469500 (2010).

4 NATURE COMMUNICATIONS | 4:1498 | DOI: 10.1038/ncomms2510 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications

& 2013 Macmillan Publishers Limited. All rights reserved.

NATURE COMMUNICATIONS | DOI: 10.1038/ncomms2510 ARTICLE

4. Meillaud, F., Shah, A., Droz, C., Vallat-Sauvain, E. & Miazza, C. Efciency limits for single-junction and tandem solar cells. Solar Energ. Mater. Solar Cells 90, 29522959 (2006).

5. LaPierre, R. R. Theoretical conversion efciency of a two-junction III-V nanowire on Si solar cell. J. Appl. Phys. 110, 014310 (2011).

6. Davydok, A., Breuer, S., Biermanns, A., Geelhaar, L. & Pietsch, U. Lattice parameter accommodation between GaAs (111) nanowires and Si (111) substrate after growth via Au-assisted molecular beam epitaxy. Nanoscale Res. Lett. 7, 109 (2012).

7. Krogstrup, P. et al. Structural phase control in self-catalyzed growth of gaas nanowires on silicon (111). Nano. Lett. 10, 44754482 (2010).

8. Mrtensson, T. et al. Epitaxial III V nanowires on silicon. Nano. Lett. 4,

19871990 (2004).9. Mohseni, P. K., Rodrigues, A. D., Galzerani, J. C., Pusep, Y. A. & LaPierre, R. R. Structural and optical analysis of GaAsP/GaP core-shell nanowires. J. Appl. Phys. 106, 124306 (2009).

10. Tchernycheva, M. et al. Photovoltaic properties of GaAsP coreshell nanowires on Si(001) substrate. Nanotechnology 23, 265402 (2012).

11. Dubois, S., Palais, O., Pasquinelli, M., Martinuzzi, S. & Jaussaud, C. Inuence of substitutional metallic impurities on the performances of p-type crystalline silicon solar cells: The case of gold. J. Appl. Phys. 100, 123502 (2006).

12. Bar-Sadan, M., Barthel, J., Shtrikman, H. & Houben, L. Direct Imaging of single Au atoms within GaAs nanowires. Nano. Lett. 12, 23522356 (2012).

13. Breuer, S. et al. Suitability of Au-and self-assisted GaAs nanowires for optoelectronic applications. Nano. Lett. 11, 12761279 (2011).

14. Kelzenberg, M. D. et al. Enhanced absorption and carrier collection in Si wire arrays for photovoltaic applications. Nat. Mater. 9, 239244 (2010).

15. Wei, W. et al. Direct heteroepitaxy of vertical InAs nanowires on si substrates for broad band photovoltaics and photodetection. Nano. Lett. 9, 29262934 (2009).

16. Fontcuberta i Morral, A., Colombo, C., Abstreiter, G., Arbiol, J. & Morante, J. R. Nucleation mechanism of gallium-assisted molecular beam epitaxy growth of gallium arsenide nanowires. Appl. Phys. Lett. 92, 063112 (2008).

17. Colombo, C., Heib, M., Gratzel, M. & Fontcuberta i Morral, A. Gallium arsenide p-i-n radial structures for photovoltaic applications.. Appl. Phys. Lett. 94, 173108 (2009).

18. Gutsche, C. et al. n-GaAs/InGaP/p-GaAs core-multishell nanowire diodes for efcient light-to-current conversion. Adv. Funct. Mater. 22, 929936 (2011).

19. Kempa, T. J. et al. Coaxial multishell nanowires with high-quality electronic interfaces and tunable optical cavities for ultrathin photovoltaics. Proc. Natl Acad. Sci. USA 109, 14071412 (2012).

20. Shockley, W. & Queisser, H. J. Detailed balance limit of efciency of p-n junction solar cells. J. Appl. Phys. 32, 510519 (1961).

21. Heiss, M. & Fontcuberta i Morral, A. Fundamental limits in the external quantum efciency of single nanowire solar cells. Appl. Phys. Lett. 99, 263102 (2011).

22. Yu, S., Roemer, F. & Witzigmann, B. Analysis of surface recombinationin nanowire array solar cells. Proc. SPIE 8438, Photonics for Solar Energy Systems IV. (eds Wehrspohn, R. & Gombert, A.) 84380O (International Society of Optics and Photonics, 2012).

23. Plissard, S., Larrieu, G., Wallart, X. & Caroff, P. High yield of self-catalyzed GaAs nanowire arrays grown on silicon via gallium droplet positioning. Nanotechnology 22, 275602 (2011).

24. Goto, H. et al. growth of coreshell InP nanowires for photovoltaic application by selective-area metal organic vapor phase epitaxy. Appl, Phys, Express, 2, 035004 (2009).

Acknowledgements

This work has been supported by the Danish National Advanced Technology Foundation through project 022-2009-1, by the EU through FP7-SME programme support to project PolyGlass, a University of Copenhagen Centre of Excellence and by the UNIK Synthetic Biology project. We thank Dr Ray LaPierre (McMaster University) for fruitful discussions, Dr Erik Johnson (University of Copenhagen) for assistance with transmission electron microscopy characterization and Kevin Lee (University College London) for assisting with MBE growths.

Author contributions

H.L. and M.A. performed material growth. H.I.J., J.V.H., H.L., M.A. and P.K. assisted with growth development and characterization. H.I.J., J.V.H. and M.A. collaborated on device design, fabrication, measurement and assessment. J.N. supervised P.K. and participated in discussions throughout the work. All the authors contributed to preparation of the manuscript.

Additional information

Supplementary Information accompanies this paper on http://www.nature.com/naturecommunications

Web End =http://www.nature.com/ http://www.nature.com/naturecommunications

Web End =naturecommunications

Competing nancial interests: The authors declare no competing nancial interests.

Reprints and permission information is available online at http://npg.nature.com/reprintsandpermissions/

Web End =http://npg.nature.com/ http://npg.nature.com/reprintsandpermissions/

Web End =reprintsandpermissions/

How to cite this article: Holm, J.V. et al. Surface-passivated GaAsP single-nanowire solar cells exceeding 10% efciency grown on silicon. Nat. Commun. 4:1498doi: 10.1038/ncomms2510 (2013).

NATURE COMMUNICATIONS | 4:1498 | DOI: 10.1038/ncomms2510 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications 5

& 2013 Macmillan Publishers Limited. All rights reserved.