Full Text

Turn on search term navigation

ARTICLE

Received 11 Jan 2015 | Accepted 14 May 2015 | Published 1 Jul 2015

Dehui Li1, Rui Cheng2, Hailong Zhou1, Chen Wang2, Anxiang Yin1, Yu Chen2, Nathan O. Weiss2, Yu Huang2,3 & Xiangfeng Duan1,3

The layered transition metal dichalcogenides have attracted considerable interest for their unique electronic and optical properties. While the monolayer MoS2 exhibits a direct bandgap, the multilayer MoS2 is an indirect bandgap semiconductor and generally optically inactive. Here we report electric-eld-induced strong electroluminescence in multilayer

MoS2. We show that GaNAl2O3MoS2 and GaNAl2O3MoS2Al2O3-graphene vertical heterojunctions can be created with excellent rectication behaviour. Electroluminescence studies demonstrate prominent direct bandgap excitonic emission in multilayer MoS2 over the entire vertical junction area. Importantly, the electroluminescence efciency observed in multilayer MoS2 is comparable to or higher than that in monolayers. This strong electro-luminescence can be attributed to electric-eld-induced carrier redistribution from the lowest energy points (indirect bandgap) to higher energy points (direct bandgap) in k-space. The electric-eld-induced electroluminescence is general for other layered materials including WSe2 and can open up a new pathway towards transition metal dichalcogenide-based optoelectronic devices.

1 Department of Chemistry and Biochemistry, University of California, Los Angeles, California 90095, USA. 2 Department of Materials Science and Engineering, University of California, Los Angeles, California 90095, USA. 3 California Nanosystems Institute, University of California, Los Angeles, California 90095, USA. Correspondence and requests for materials should be addressed to X.D. (email: mailto:[email protected]

Web End [email protected] ).

NATURE COMMUNICATIONS | 6:7509 | DOI: 10.1038/ncomms8509 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications 1

DOI: 10.1038/ncomms8509 OPEN

Electric-eld-induced strong enhancementof electroluminescence in multilayer molybdenum disulde

ARTICLE NATURE COMMUNICATIONS | DOI: 10.1038/ncomms8509

The layered transition metal dichalcogenides (TMDs) have attracted considerable interest for their unique layer-number-dependent electronic and optical properties115.

The monolayer MoS2 and WSe2 exhibit a direct bandgap with strong photoluminescence and are of particular interest for new types of optoelectronic devices2,9,10,12,1620. However, the multilayer MoS2 is an indirect bandgap semiconductor and is generally believed to be optically inactive, with the photoluminescence typically 43 orders of magnitude weaker than that of the monolayers2,7, which prevents the multilayer MoS2 from being used in the eld of light-emitting devices.

To achieve efcient electroluminescence (EL), a pn junction is usually required to simultaneously inject electrons and holes that recombine to give out photon emission. In case of two-dimensional (2D) TMDs, it is possible to create either a lateral junction with a one-dimensional junction interface or a vertically stacked structure with a 2D junction interface for electron or hole injection, which are necessary for EL emission. The EL emission from the lateral junctions of mono-/few-layer TMDs has been recently reported and is typically limited to the local area across the one-dimensional junction interface2127, because the full depletion of the monolayer prevents efcient carrier injection throughout the entire monolayer. To achieve broad-area EL

emission, the vertically stacked structures with 2D junction interfaces are usually preferred5. However, with atomically thin thickness, the rapid carrier leakage28 across the monolayer TMDs in the vertical junctions could prevent the efcient recombination of the injected carriers and limit the EL efciency in the vertically stacked electrically driven light-emitting devices. To this end, multilayer TMDs may be benecial, which, however, are typically indirect bandgap semiconductors and normally optically inactive. Here we report strong EL emission from the entire 2D junction interface in a unique design of vertical heterostructure devices with multilayer MoS2 and WSe2 (up to B130 layers), and demonstrate a strong electric-eld-induced enhancement of the EL in indirect bandgap multilayer MoS2 and WSe2 to achieve comparable or better efciency than that of direct bandgap monolayer counterparts.

ResultsFabrication of GaNAl2O3Q3MoS2 structures. To create vertically stacked light-emitting devices based on n-type MoS2, a p-doped GaN is used to inject holes into MoS2 akes (Fig. 1a,b). A thin layer of 4-nm-thick Al2O3 was deposited on the p-type GaN (B3.8 mm p-GaN on sapphire) before transferring the

a b

Ni/Au

MoS2

Ni/Au

MoS2

Al2O3

Pd/Au

GaN

d h

Current (A)

Pd/Au

Ni/Au

MoS2

0.65 nm

Al2O3

Al2O3 GaN

GaN

0.51 nm 2 nm

8 4 0 4 8

Voltage (V)

e f

V=0 V<0

V>0

GaN

Al2O3

MoS2

Al2O3

GaN MoS2

GaN

Al2O3 MoS2

Figure 1 | Schematic illustration, structural and electrical characteristics and band diagrams of GaNAl2O3MoS2 vertical devices. (a) A schematic of the three-dimensional view of the vertically stacked device. (b) A schematic of the cross-sectional view of the device. (c) An optical image of a GaNAl2O3

MoS2 vertical device. The dashed line highlights the area with Al2O3 layer and bare GaN surface. Scale bar, 4 mm. (d) A cross-sectional high-resolution transmission electron microscope (TEM) image of the interfaces across the GaN substrate, Al2O3 and MoS2 ake vertical stack. The layer number of the MoS2 ake is 14. (e) The ideal band diagram of the vertical heterostructure at zero bias. The dashed lines indicate the position of Fermi levels. At zero bias, the bottom of the conduction band and the top of the valence band of MoS2 fall within the forbidden bandgap of GaN. (f) The ideal band diagram of the vertical heterostructure under forward bias. (g) The ideal band diagram of the heterostructure under reverse bias. (h) Current versus bias voltage characteristic of a vertically stacked device.

2 NATURE COMMUNICATIONS | 6:7509 | DOI: 10.1038/ncomms8509 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications

NATURE COMMUNICATIONS | DOI: 10.1038/ncomms8509 ARTICLE

mechanically exfoliated MoS2 akes (see Methods). The insulating Al2O3 layer can partly block the electrons to inject from n-MoS2 to p-GaN while allowing holes to be effectively injected from p-GaN to n-MoS2 due to the unique band alignment (see band diagram in Fig. 1f,g and further discussion below), where the desired EL occurs29. In addition, the insulating layer can also suppress the direct tunnelling of electrons or holes from the top electrode to GaN substrate (through the thin MoS2 akes) to improve the EL efciency. A Ni/Au metal thin lm was used as the top-contact electrodes at the edge of the MoS2 and the p-GaN substrate was contacted with a Pd/Au metal thin lm (Supplementary Fig. 1). Figure 1c displays an optical image of the top view of a typical device on the GaN substrate, where the MoS2 ake and electrodes are indicated. A high-resolution cross-sectional transmission electron microscope image clearly shows the interfaces of the GaNAl2O3MoS2 vertical stack (Fig. 1d).

Output characteristics of GaNAl2O3MoS2 structures. Figure 1eg shows the ideal band diagrams of the vertical heterostructures. At or near the zero bias, the insulating layer blocks both electrons and holes from passing through the heterojunction with a zero current (Fig. 1e). It should be noted that the valence band energy difference between GaN and Al2O3 (DEv 1 eV) is

much smaller than that of the conduction bands (DEc 2.2 eV).

As a consequence, it is much easier for holes to be injected from GaN to MoS2 akes due to a relatively lower potential barrier.

Applying a positive voltage to p-type GaN will drive the holes to tunnel from GaN to MoS2, resulting in a forward current (Fig. 1e). Further increasing the applied positive voltage on the GaN, the holes in GaN can even thermally emit into MoS2, with the injection current rapidly increasing with the bias voltage. Under sufcient high voltage, electrons in MoS2 are able to tunnel to the conduction band of the GaN, which can also contribute to the forward current and lead to the emission from the GaN substrate. Under a negative bias, the top of the valence band of GaN falls within the bandgap of MoS2, while the bottom of the conduction band of MoS2 falls within the bandgap of GaN (Fig. 1g). Therefore, there is no available state for both electrons and holes to tunnel through the insulating layer, resulting in zero current. The currentvoltage output characteristic (Fig. 1h) shows clear current rectication behaviour, demonstrating excellent diode characteristics in the GaNAl2O3MoS2 vertical devices to satisfy the basic requirement for high-efciency EL devices.

EL in GaNAl2O3MoS2 structures. Importantly, both the monolayer and multilayer MoS2 can exhibit clear EL emission under a forward bias. The EL spectra of a monolayer and a 50-layer MoS2 device are shown in Fig. 2a,b. To identify and assign the origin of the EL peaks, the photoluminescence (PL) spectra of GaN and MoS2 are displayed as well. With close comparison of the EL spectra with the PL spectra, we can unambiguously assign the EL emission peak around 530 nm to the defect emission of the GaN substrate, the peak at 667 nm to the exciton A emission in the monolayer MoS2 and the peaks at 691 and 635 nm to the exciton A and B emission, respectively, in the 50-layer MoS2 device30. The small periodic oscillations can be attributed to the interference patterns formed due to the GaN substrate. For both monolayer and multilayer MoS2 devices, the

EL peaks show a small redshift compared with the corresponding PL peaks due to a self-heating effect, which is commonly seen in EL spectra of traditional semiconductor heterostructures31. It is also noted that the full width at half maximum of EL peaks of MoS2 is much broader than that of corresponding PL peaks, which may be attributed to the electric-eld-induced peak broadening32.

To focus on the EL only from MoS2, we insert a longpass lter with a cutoff wavelength of 650 nm to eliminate the emission from the GaN substrate. Figure 2c,d shows the optical image and EL mapping for the monolayer and the 50-layer MoS2 akes, respectively. The prole of MoS2 akes and the contact electrodes are outlined by dashed lines to identify the position of the EL. Importantly, bright EL are clearly seen from entire overlapping area of the vertical heterostructures for both the monolayer and multilayer MoS2 akes. The non-uniform distribution of the EL may be attributed to the imperfect interfaces (or impurities) due to the wet transfer process, the surface roughness of the p-GaN substrate and/or non-uniform eld distribution.

Next, we have investigated the thickness dependence to probe the inuence of thickness on the EL efciency and understand the mechanism for the enhanced EL in the multilayer indirect bandgap MoS2. To properly compare the EL efciency among different devices, we have normalized the EL spectra by injecting current density, which is proportional to the EL efciency. Interestingly, the overall normalized intensity for all devices with different MoS2 thickness (including the monolayer and thicker one up to 50 layers) is highly comparable to each other (Fig. 2e; Supplementary Fig. 2). Both the exciton A and B can be identied in the EL spectra of MoS2 akes thicker than 6 nm, whereas only exciton A emission can be clearly seen from EL spectra of the thinner akes, which may be ascribed to the stronger electric-eld-induced peak broadening in the thin layers. In the thinner akes, the electric eld is much stronger and the eld-induced peak broadening is so severe that the exciton A and B emission merge into one broad peak32.

The observation of nearly comparable EL intensity in monolayer and multilayer MoS2 is quite striking when considering the PL intensity is strongly dependent on the number of layers in these TMD materials. With a direct bandgap, monolayer can typically exhibit rather strong PL, which deceases rapidly with the increasing number of atomic layers due to the crossover from a direct bandgap semiconductor to an indirect one with increasing layer number2,7. For the PL process, the photogenerated carriers undergo rapid thermalization and reach thermal equilibrium in a timescale much shorter than that of radiative recombination33, with the majority of carriers occupying their immediate band extremum, that is, electrons at L valley and holes at G hill of k-space in multilayer MoS2. As a result, the direct bandgap recombination at the K point is rather weak due to the lack of carrier occupation at the K point in multilayer MoS2 under thermal equilibrium. As the thickness increases, less and less carriers occupy the K point due to the increasing energy difference between the K valley and L valley for electrons (DEL K) and between the K hill and G hill for holes (DEG K),

resulting in an exponential decrease of the PL intensity with the increase of MoS2 thickness7.

Electric-eld-induced carrier redistribution. This distinct contrast between EL and PL is particularly evident in the plot of EL and PL versus layer thickness, in which both EL and PL intensity observed in different layered samples are normalized by the EL and PL intensity of the monolayer MoS2 (Fig. 2e). If we dene the ratio of the EL intensity to PL intensity as a relative electric-eld-induced EL enhancement factor, the enhancement factor increases with the increasing MoS2 layer number and reaches as large as B2,000 for a 50-layer sample (right axis of the Fig. 2f). It should be noted that the EL in all multilayer MoS2 originates from the direct bandgap (KK) transition rather than the near-band-edge (LG) transition. This can occur due to the fact that the electric eld could induce carrier redistribution from low energy points to high energy points of the k-space (Fig. 3a,b), leading to a non-equilibrium distribution of the injected carriers

NATURE COMMUNICATIONS | 6:7509 | DOI: 10.1038/ncomms8509 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications 3

ARTICLE NATURE COMMUNICATIONS | DOI: 10.1038/ncomms8509

a b

1 L

2 L

4 L

6 L

24 L

50 L

900

1 L

A 50 L

1,200

1,500

Normalized intensity (a.u.)

600

EL (a.u.)

800

300

400

1,000

400

GaN

MoS2

400

GaN

MoS2

300

500

PL (a.u.)

200

PL (a.u.)

/300

200

100

0 500 600 700 800

0 500

600 700 800

Wavelength (nm)

18 k

EL (counts)

2,500

100

2,000

101

Integrated intensity (a.u.)

Enhancement factor

1,500

18 k

EL (counts)

1,000

102

500

103

1 10 100

Layer number

Figure 2 | Electroluminescence (EL) from GaNAl2O3MoS2 vertical devices. (a) The EL spectrum of a monolayer device under an injection current of 30 mA. The PL spectra of the GaN substrate and the same monolayer MoS2 ake (divided by 300) are given as well to assign the EL peaks. (b) The EL spectrum of a 50-layer MoS2 device under an injection current of 88 mA. The PL spectra of the GaN substrate and the same 50-layer MoS2 ake (multiplied by 6) are shown as well. The PL intensity of monolayer MoS2 is around 2,000 times larger than that of 50-layer MoS2. (c) The optical image and the corresponding EL mapping for the same monolayer device. The monolayer MoS2 ake and electrode are outlined by dashed lines. A 650-nm longpass lter was used for mapping the emission from MoS2 only. Scale bar, 3 mm. (d) The optical image and the corresponding EL mapping for the same 50-layer MoS2 device. The 50-layer MoS2 ake and electrode are outlined by dashed lines. Scale bar, 3 mm. A 650-nm longpass lter was used for mapping the emission from MoS2 only. (e) The EL spectra from MoS2 akes with various number of layers. The spectra have been normalized by the injection current density to compare with each other, and the GaN emission has been subtracted based on a Gaussian tting. (f) The normalized integrated EL and PL intensity (left axis) and the relative enhancement factor dened as the ratio of EL intensity to the PL intensity (right axis) as a function of the layer number.

in the multilayer indirect bandgap MoS2. Under the applied electric eld, the injected electrons and holes are accelerated to gain signicant kinetic energy. Thus, the electron and hole temperature are signicantly higher than that of the environment, causing electrons to transfer from L valley to K valley while holes to transfer from G hill to K hill24,34. In this way, electrons and holes can recombine at the K point, leading to greatly enhanced direct bandgap EL in multilayer MoS2.

It should be noted that the indirect bandgap exciton binding energy is rather large for bilayer and trilayer MoS2 (around 400 meV for bilayer and around 100 meV for trilayer)35, which can greatly suppress the electric-eld-induced carrier redistribution. Consequently, EL in bilayer and trilayer MoS2 is rather weak.

When the thickness is larger than three layers, the indirect bandgap exciton binding energy decreases to about 25 meV35. As a result, the indirect bandgap excitons are mostly ionized at room temperature and can be efciently redistributed to direct bandgap K points under high electrical eld for EL emission. We have calculated the K-point population fraction for electrons n2/(n1 n2) and holes p2/(p1 p2) as a function of the applied

electric eld for MoS2 thicker than 3 layers (Fig. 3c,d; Supplemen-

tary Note 1). The K-point population fraction for both electrons and holes starts to increase around 40 kV cm 1 and saturates at 1 MV cm 1 with a saturation value of B0.8. Such a large fraction of population at a higher-energy direct bandgap K point is quite striking and largely responsible for the enhanced EL emission in multilayer MoS2, which is usually difcult to achieve in other indirect bandgap semiconductors (for example, Si), but has been observed in a number of direct bandgap semiconductors (for example, GaAs, InP)34,36. This unique electric-eld-enhanced EL can be attributed to the unique band structure of MoS2: the density of states at the K point is much larger than that at the L(G) point due to the larger effective mass at the K valley(hill) and the larger number of equivalent hill numbers at K points (6) compared with that at G points (1)37. Indeed, the density-of-state ratio is evaluated to be 6.4 for holes between the K hill and G hill and 10.6 for electrons between K valley and L valley (Supplementary Note 1 and Supplementary Table 1). With much higher density of states at the K point in MoS2, it is not totally surprising to expect that the majority of the injected carriers can redistribute to the higher-energy K valleys or hills, which is responsible for the enhanced EL in our devices.

4 NATURE COMMUNICATIONS | 6:7509 | DOI: 10.1038/ncomms8509 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications

NATURE COMMUNICATIONS | DOI: 10.1038/ncomms8509 ARTICLE

0.8

n 2/(n 1+n 2)

0.4

4 L

5 L

6 L

Bulk

p 2/(p 1+p 2)

0.4

4 L

5 L

6 L

Bulk

0.0

0.0 0.5 1.0 0.0 0.5 1.0

Field (MV cm1)

Figure 3 | The schematic of the carrier transfer processes and the calculated valley/hill population fraction. (a) The schematic illustration of the conduction band and valence band. (b) The electric-eld-induced carrier transfer between different energy valleys and hills. The equivalent valley number and hill number are 6 at K and L points and 1 at the G point.

(c) The calculated electron population fraction at the K valley as a function of the applied electric eld for different thickness MoS2 akes. (d) The calculated hole population fraction at the K hill as a function of the applied electric eld for different thickness MoS2 akes.

GaNAl2O3MoS2Al2O3-graphene structures. With the GaN Al2O3MoS2 structures, a metal electrode is deposited on the edge of the MoS2 ake for electron injection. Due to the resistivity and depletion of MoS2 along both the lateral and vertical direction, there are both vertical and lateral components of electric eld. It is therefore difcult to precisely determine the exact electrical eld and quantitatively correlate the experimental results with the theoretical ones. To further verify the proposed mechanism, we have created vertically stacked GaNAl2O3MoS2Al2O3-graphene heterostructures (Fig. 4a), in which graphene is used as the top electrode. In this case, the applied electric eld is largely dominated by the vertical component. We have also included a 4-nm-thick Al2O3 layer between the MoS2 and graphene in the new heterostructures to prevent electrons and holes from directly transferring to graphene, which would quench the EL in MoS2.

The currentvoltage characteristic of this new structure also shows excellent diode behaviour (Fig. 4b). However, the injection current is typically several times smaller than that of previous GaNAl2O3MoS2 structures at the same bias voltage due to the additional tunnelling layer between MoS2 and graphene.

EL in GaNAl2O3MoS2Al2O3-graphene structures. Figure 4c displays the optical image, EL mapping and PL mapping of a typical device with the MoS2 ake composed of two parts with different thicknesses (lower part with a thickness of 36 nm and upper part with a thickness of 92 nm). The EL mapping shows several important features: rstly, EL is observed from the entire heterojunction area, conrming the formation of a broad-area vertical junction; secondly the thicker part of the ake exhibits a

stronger EL signal than the thinner area, which is in striking contrast to the PL mapping of the same sample in which the thinner part clearly shows a stronger PL emission. EL spectra further conrm that the EL intensity of the thicker part is around1.5 times stronger than that of the thinner part under the same injection condition (Fig. 4d), while the corresponding PL intensity in the thicker part is o40% of that in the thinner area (Fig. 4e).

We have also investigated the EL characteristics as a function of injection current or vertical electric eld. The EL intensity increases monotonously with the injection current and saturates around the injection current of 174 mA (Fig. 4f,g; Supplementary

Fig. 3). It is also noted that the EL emission from GaN continues to increase with the increasing injection current after the MoS2 emission reaches saturation (Supplementary Fig. 3), suggesting the EL saturation in MoS2 under high injection current (eld) is a unique feature of MoS2. Overall, the EL efciency in MoS2 increases rapidly rst and then decreases with the increasing injection current (Fig. 4g) or the increasing electric eld (Fig. 4h). The vertical electric eld is determined by the current density and carrier mobility (Supplementary Figure 4 and Supplementary Note 2) using a space-charge-limited current model (Supplementary Figure 5 and Supplementary Note 3).

The trend of EL efciency with increasing electric eld may be attributed to two competing factors under high electric eld that may affect the emission efciency in the opposite way: the increase of the electron and hole population fraction at direct bandgap K point and increase of carrier temperature. To account for this trend, we calculated the relative EL efciency under various electric elds by taking into account both the electric-eld-induced carrier redistribution and carrier temperature38 (blue curve in Fig. 4h; Supplementary Figure 6 and Supplementary Note 1). In general, the electron, hole temperature and their population in the higher-energy K points all increase with the increasing electric eld. The increase of the electron and hole population faction at the direct bandgap K point would result in a higher EL efciency, while the increasing average carrier temperature could reduce the EL efciency. Together, these two competing factors could lead to an increase of EL efciency with the electric eld at lower-eld regime (where the rapid increase of carrier population at the K point dominates the EL efciency, see Fig. 3c,d and Fig. 4h), followed by a decrease of EL efciency at higher electric eld (where the carrier population at the K point saturates, and the effect of the carrier temperature dominates the EL efciency, see Fig. 3c,d and Fig. 4h). Importantly, the observed EL efciency rst increases and then decreases with the increasing electric eld (red dots in Fig. 4h), which is consistent with the trend predicted by the theoretical calculations (blue line in Fig. 4h), except at low-eld (small injection current) regime where the space-charge-limited current model used to calculate the electric eld underestimates the eld in MoS2 (Supplementary

Figure 6 and Supplementary Note 3). The decrease in EL efciency may also be partly attributed to the increased electron injection from MoS2 to GaN substrate under high electric eld28, which is supported by the continued increase of GaN emission after the saturation of emission in MoS2 under high electric eld (Supplementary Fig. 3). In addition, other factors such as eld-induced exciton ionization and excitonexciton annihilation may also contribute to the decrease in EL efciency under high injection current (eld).

Thickness dependence of the EL efciency. We have further probed the thickness dependence of the EL efciency based on GaNAl2O3MoS2Al2O3-graphene heterostructures. The EL intensity normalized by the injection current density indicates

NATURE COMMUNICATIONS | 6:7509 | DOI: 10.1038/ncomms8509 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications 5

ARTICLE NATURE COMMUNICATIONS | DOI: 10.1038/ncomms8509

a c

Ti/Au

Graphene

Al2O3

MoS2

Pd/Au

0 600 700 800

GaN

0 3 k 0 3 k EL (counts) PL (counts)

0 300 k 600 k

b d e

20 k

Thin

Thick

150 Thin

Thick

EL intensity (a.u.)

Current (A)

PL intensity (a.u.)

100

10 k

8 4 0 4 8

630 660 690

Voltage (V)

Wavelength (nm)

f g h

20 k

A 3 A

73 A

174 A

208 A

0.9

Efficiency (a.u.)

EL intensity (a.u.)

Integrated intensity (a.u.)

10 k

0.6

Efficiency (a.u.)

0.6

0.3

The

Exp

0.0

600 700 800

0 100 200

Field (V cm1)

Figure 4 | EL from vertically stacked GaNAl2O3MoS2Al2O3-graphene heterostructures. (a) A schematic illustration of the cross-sectional view of the GaNAl2O3MoS2Al2O3-graphene vertical heterostructure. (b) Current versus bias voltage characteristic of the GaNAl2O3MoS2Al2O3-graphene vertical device. (c) The optical image, EL mapping (under an injection current of 8 mA) and PL mapping ( excited by a 514-nm Ar ion laser) of a multilayer device. The MoS2 ake is composed of two parts with different thicknesses: the 36-nm-thick lower part and the 92-nm-thick upper part. Scale bar, 3 mm.

(d) EL spectra from the thick part and thin part of the MoS2 ake under an injection current of 174 mA. The GaN emission has been subtracted based on a Gaussian tting. (e) PL spectra from the thick part and thin part of the same MoS2 ake. (f) EL spectra of the thick part at different injection currents. The GaN emission has been subtracted based on the Gaussian tting. The corresponding applied voltages are 6, 13, 17 and 18 V. (g) The integrated EL intensity and EL efciency as a function of the injection current for the thick part. (h) The EL efciency as a function of the electric eld. The discrete points are experimental results and the solid line is the theoretical calculation.

Wavelength (nm)

Current (A)

0.0

that both exciton A and B peaks are present for all akes with various thicknesses (692 nm) (Fig. 5a; Supplementary Fig. 7). The EL efciency for the current structures is about three times higher than that in the previous GaNAl2O3MoS2 structures, likely due to the carrier leakage through the metal electrode in previous structures (Supplementary Fig. 8). Importantly, a clear trend is observed that the normalized integrated EL intensity increases with the increasing ake thickness (Fig. 5b), which might be attributed to at least two factors. First, the applied electric eld would be smaller in the thicker akes for a xed applied bias voltage, leading to a larger EL efciency under the same injection current (see Fig. 4g, in the high-eld regime where the EL efciency decreases with increasing electric eld). The second factor is the injected carrier leakage28. The thicker the ake is, the smaller the percentage of the injected carrier can leak away from the active emitters, resulting in a higher EL efciency. The theoretical calculation based on the above discussion agrees well with the experimental results (Fig. 5b; Supplementary Note4). The relatively large discrepancy for the thinner akes may arise from the inaccurate energy difference DEL K and DEG K

and effective mass that can be different from the bulk values used in the calculation39.

4 k 6 nm 36 nm 60 nm 92 nm

0.9 Exp

Normalized intensity (a.u.)

The

3 k

0.6

2 k

Intensity(a.u.)

0.3

1 k

0.0

0 600 700 800

0 40 80

Wavelength (nm)

Thickness (nm)

Figure 5 | Thickness-dependent EL for vertically stacked GaNAl2O3

MoS2Al2O3-graphene heterostructures. (a) The normalized EL spectra for vertical devices with MoS2 akes of varying thickness. The spectra are normalized by the injection of current density to compare with each other. The GaN emission has been subtracted based on a Gaussian tting. (b) The integrated EL intensity as a function of the thickness of the MoS2 akes. The red points are experimental results and the blue hollow squares are obtained from theoretical calculation.

6 NATURE COMMUNICATIONS | 6:7509 | DOI: 10.1038/ncomms8509 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications

NATURE COMMUNICATIONS | DOI: 10.1038/ncomms8509 ARTICLE

DiscussionAfter calibrating the collection efciency of our EL measurement system, we have estimated the EL external quantum efciency of our vertical heterostructure devices to be around 10 4, which is about one order of magnitude larger than the EL efciency in monolayer MoS2 transistors26 and on the same order as the reported value in monolayer WSe2 planar structures23. We believed this enhanced EL in multilayer indirect bandgap MoS2 akes can be attributed to the unique energy band structure of MoS2 and the vertical heterostructure design used in the current devices. The larger effective mass and the larger number of equivalent valleys and hills at K points give rise to a larger density of state at the K point compared with that at the L point and G point of k-space (Supplementary Note 1). Furthermore, the energy differences among these different valleys or hills (DEL K

and DEG K) are relatively small. The design of vertical

heterostructure junction can create a strong vertical electric eld inside the MoS2 akes, which induces efcient carrier redistribution from low energy points (L, G) to the high energy points (K) with a larger density of state, resulting in greatly enhanced EL in the multilayer MoS2 akes. The EL efciency may be further improved by using other TMDs with smaller energy difference DEL K and DEG K, less bulk trapping states23 or

optimizing the device fabrication process to reduce interface impurities, defects and traps.

It should also be noted that the injected hot carriers through the tunnelling barriers in the vertical stack are also energetic enough to occupy the K valleys and hills and might be a possible contributing factor for the enhanced EL from the K point. However, without eld-induced carrier redistribution in the MoS2, such hot carriers cannot normally sustain high-energy states (K valleys and K hills) and would quickly relax to the lowest-energy states (L point for electrons and G point for holes)

before radiative recombination, because the hot-carrier relaxation or cooling time in MoS2 is typically on the order of sub-picosecond level while the radiative recombination time is on the order of nanosecond40,41. In addition, if the enhanced EL were a direct result of hot-carrier injection, the shape of EL spectra should strongly depend on the electric eld/injection current, and the emission peaks should be very broad and not associated with distinct energy bands. In contrast, our experimental results show that the overall shape of the EL spectra in multilayer MoS2 remains nearly the same with the increasing electric eld/ injection current (Fig. 4f) and displays two distinct peaks located at the same positions as PL emission peaks. Finally, our eld-induced carrier redistribution model can well explain the overall trend of EL efciency with electric eld (Fig. 4h), which cannot be consistently interpreted using the hot-carrier injection model. Together, although the injected hot carriers may be energetic enough to occupy K valleys and hills, such hot carriers cannot sustain high-energy states for radiative recombination, and the electric-eld-induced carrier redistribution is the key factor for ensuring sufcient carrier population in K valleys and hills for radiative recombination and thus enhanced EL emission.

In summary, our studies for the rst time report the broad-area EL emission from the entire junction area of the vertically stacked heterostructures of MoS2, and demonstrate unusually strong EL emission in the indirect bandgap multilayer MoS2. This unique EL characteristics cannot be easily achieved in other traditional indirect semiconductors (for example, Si), and is fundamentally originated from the unique electronic band structures of multilayer MoS2, and general for other TMD materials. Indeed, our preliminary studies indicate the electric-eld-enhanced EL can also be observed in other multilayer TMDs (for example, WSe2,

see Supplementary Note 5 and Supplementary Fig. 9). Our studies can thus not only offer a fundamental platform to probe the

carrier injection, population and recombination in multilayer TMDs under high electric eld, but also open up a pathway towards new types of light-emitting devices with spin- and valley polarization25 based on multilayer TMDs.

Methods

Device fabrication. MoS2 samples are mechanically exfoliated from a bulk MoS2 crystal onto a 285-nm Si/SiO2 substrate with alignment markers and then transferred onto the p-GaN substrate with a doping level of 2 1017 cm 3 grown by

metalorganic chemical vapour deposition. A layer of 4-nm-thick Al2O3 was

deposited on the GaN substrate using atomic layer deposition before MoS2 akes were transferred. Then a layer of 60-nm-thick Al2O3 was deposited to insulate the substrate and top electrodes. Windows were dened by electron beam lithography followed by 6:1 buffered oxide etch to remove the Al2O3 on the top of MoS2 samples and on GaN for depositing the contact electrodes. Finally, an electron beam evaporation process was employed to deposit 5-nm Ni/50-nm Au metal thin lms as top-contact electrodes at the edge of the MoS2 and 5-nm Pd/50-nm Au as the bottom electrode on the GaN substrate to form Ohmic contact (Supplementary Fig. 1). For vertically stacked GaNAl2O3MoS2Al2O3-graphene devices, a 4-nm-thick Al2O3 was deposited after opening the windows. The graphene grown by the chemical vapour deposition method was transferred onto the top of the windows. Then the transferred graphene was patterned by electron-beam lithography followed by oxygen plasma etching so that the graphene only covers the MoS2 akes. Finally, 20-nm Ti/50-nm Au electrodes were dened on the edge of the graphene and 5-nm Pd/50-nm Au electrodes were deposited on the GaN substrate.

Microscopic, electrical and optical characterizations. The thickness of the MoS2 akes was determined by tapping-mode atomic force microscopy (Vecco 5,000 system). The cross-section image of the vertical devices was acquired in an FEI Titan high-resolution transmission microscopy. The electrical measurement was carried out in a probe station (Lakeshore, TTP4) coupled with a precision source/ measurement unit (Agilent B2902A). The PL measurement was conducted under a confocal mirco-Raman system (Horiba LABHR) equipped with a 600-mm 1 grating in a backscattering conguration excited by an Ar ion laser (514 nm) with an excitation power of 500 mW. The PL measurement of the GaN substrate was excited by a 257-nm laser with a power of 200 mW.

EL measurement. The EL measurement was carried out under a home-built micro-PL system (Acton 2300i spectrometer equipped with a 150-mm 1 grating)

combining with a precision source/measurement unit (Agilent B2902A) to force voltage or current. The EL signal was collected using a 50 objective (numerical

aperture 0.5) and acquired by liquid nitrogen-cooled CCD (Princeton instru

ments PyLoN 400F).

References

1. Novoselov, K. S. et al. Two-dimensional atomic crystals. Proc. Natl Acad. Sci. USA 102, 1045110453 (2005).

2. Mak, K. F., Lee, C., Hone, J., Shan, J. & Heinz, T. F. Atomically thin MoS2: a new direct-gap semiconductor. Phys. Rev. Lett. 105, 136805 (2010).

3. Geim, A. & Grigorieva, I. Van der Waals heterostructures. Nature 499, 419425 (2013).

4. Yu, W. J. et al. Highly efcient gate-tunable photocurrent generation in vertical heterostructures of layered materials. Nat. Nanotechnol. 8, 952958 (2013).

5. Lopez-Sanchez, O. et al. Light generation and harvesting in a van der Waals heterostructure. ACS Nano 8, 30423048 (2014).

6. Cao, T. et al. Valley-selective circular dichroism of monolayer molybdenum disulphide. Nat. Commun. 3, 887 (2012).

7. Tongay, S. et al. Monolayer behaviour in bulk ReS2 due to electronic and vibrational decoupling. Nat. Commun. 5, 3252 (2014).

8. Yu, W. J. et al. Vertically stacked multi-heterostructures of layered materials for logic transistors and complementary inverters. Nat. Mater. 12, 246252 (2013).

9. Jones, A. M. et al. Spin-layer locking effects in optical orientation of exciton spin in bilayer WSe2. Nat. Phys. 10, 130134 (2014).

10. Wu, S. et al. Electrical tuning of valley magnetic moment through symmetry control in bilayer MoS2. Nat. Phys. 9, 149153 (2013).

11. Chhowalla, M. et al. The chemistry of two-dimensional layered transition metal dichalcogenide nanosheets. Nat. Chem. 5, 263275 (2013).

12. Wang, Q. H., Kalantar-Zadeh, K., Kis, A., Coleman, J. N. & Strano, M. S. Electronics and optoelectronics of two-dimensional transition metal dichalcogenides. Nat. Nanotechnol. 7, 699712 (2012).

13. Radisavljevic, B., Radenovic, A., Brivio, J., Giacometti, V. & Kis, A. Single-layer MoS2 transistors. Nat. Nanotechnol. 6, 147150 (2011).

14. Lopez-Sanchez, O., Lembke, D., Kayci, M., Radenovic, A. & Kis, A. Ultrasensitive photodetectors based on monolayer MoS2. Nat. Nanotechnol. 8, 497501 (2013).

NATURE COMMUNICATIONS | 6:7509 | DOI: 10.1038/ncomms8509 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications 7

ARTICLE NATURE COMMUNICATIONS | DOI: 10.1038/ncomms8509

15. Roy, K. et al. Graphene-MoS2 hybrid structures for multifunctional photoresponsive memory devices. Nat. Nanotechnol. 8, 826830 (2013).

16. Xiao, D., Liu, G., Feng, W., Xu, X. & Yao, W. Coupled spin and valley physics in monolayers of MoS2 and other group-VI dichalcogenides. Phys. Rev. Lett. 108, 196802 (2012).

17. Mak, K. F. et al. Tightly bound trions in monolayer MoS2. Nat. Mater. 12,

207211 (2013).

18. Britnell, L. et al. Strong light-matter interactions in heterostructures of atomically thin lms. Science 340, 13111314 (2013).

19. Britnell, L. et al. Field-effect tunneling transistor based on vertical graphene heterostructures. Science 335, 947950 (2012).

20. Withers, F. et al. Light-emitting diodes by band-structure engineering in van der Waals heterostructures. Nat. Mater. 14, 301306 (2015).

21. Baugher, B. W. H., Churchill, H. O. H., Yang, Y. & Jarillo-Herrero, P. Optoelectronic devices based on electrically tunable p-n diodes in a monolayer dichalcogenide. Nat. Nanotechnol. 9, 262267 (2014).

22. Pospischil, A., Furchi, M. M. & Mueller, T. Solar-energy conversion and light emission in an atomic monolayer p-n diode. Nat. Nanotechnol. 9, 257261 (2014).

23. Ross, J. S. et al. Electrically tunable excitonic light-emitting diodes based on monolayer WSe2 p-n junctions. Nat. Nanotechnol. 9, 268272 (2014).

24. Jo, S., Ubrig, N., Berger, H., Kuzmenko, A. B. & Morpurgo, A. F. Mono- and bilayer WS2 light-emitting transistors. Nano Lett. 14, 20192025 (2014).

25. Zhang, Y., Oka, T., Suzuki, R., Ye, J. & Iwasa, Y. Electrically switchable chiral light-emitting transistor. Science 344, 725728 (2014).

26. Sundaram, R. S. et al. Electroluminescence in single layer MoS2. Nano Lett. 13, 14161421 (2013).

27. Cheng, R. et al. Electroluminescence and photocurrent generation from atomically sharp WSe2/MoS2 heterojunction pn diodes. Nano Lett. 14, 55905597 (2014).

28. Yamakoshi, S., Sanada, T., Wada, O., Umebu, I. & Sakurai, T. Direct observation of electron leakage in InGaAsP/InP double heterostructure. Appl. Phys. Lett. 40, 144146 (1982).

29. Min, K. W. et al. White-light emitting diode array of p -Si/aligned n-SnO2 nanowires heterojunctions. Adv. Funct. Mater. 21, 119124 (2011).

30. Splendiani, A. et al. Emerging photoluminescence in monolayer MoS2. Nano Lett. 10, 12711275 (2010).

31. Fukai, Y. K., Matsuoka, Y. & Furuta, T. Measuring the junction temperature of AlGaAs/GaAs heterojunction bipolar transistors using electroluminescence. Appl. Phys. Lett. 63, 340342 (1993).

32. Li, D., Zhang, J., Zhang, Q. & Xiong, Q. Electric-eld-dependent photoconductivity in CdS nanowires and nanobelts: exciton ionization, FranzKeldysh, and Stark effects. Nano Lett. 12, 29932999 (2012).

33. Pankove, J. I. Optical Processes in Semiconductors (Courier Dover Publications, 2012).

34. Sze, S. M. & Ng, K. K. Physics of Semiconductor Devices (John Wiley & Sons, 2006).

35. Yamada, H.-P. & Krasheninnikov, A. V. Effects of connement and environment on the electronic structure and exciton binding energy of MoS2 from rst principles. Phys. Rev. B 86, 241201 (2012).

36. Yamada, Y. A study on nonstationary electron transport in submicron BP-SAINT GaAs MESFETs using an ensemble Monte Carlo simulation. IEICE Trans. E74-C, 16481655 (1991).

37. Peelaers, H. & Van de Walle, C. G. Effects of strain on band structure and effective masses in MoS2. Phys. Rev. B 86, 241401 (2012).

38. Basu, P. K. Theory of Optical Processes in Semiconductors: Bulk and Microstructures (Oxford Univ. Press, 1997).

39. Yun, W. S., Han, S., Hong, S. C., Kim, I. G. & Lee, J. Thickness and strain effects on electronic structures of transition metal dichalcogenides: 2H-MX2 semiconductors (M Mo, W; X S, Se, Te). Phys. Rev. B 85, 033305 (2012).

40. Nie, Z. et al. Ultrafast carrier thermalization and cooling dynamics in few-layer MoS2. ACS Nano 8, 1093110940 (2014).

41. Shi, H. et al. Exciton dynamics in suspended monoslayer and few-layer MoS2 2D crystals. ACS Nano 7, 10721080 (2013).

Acknowledgements

X.D. acknowledges support by the ONR Young Investigator Award N00014-12-1-0745. Y.H. acknowledges support by the National Science Foundation EFRI-1433541. We acknowledge the Nanoelectronics Research Facility for technical support.

Author contributions

X.D. and Y.H. designed the research. D.L. performed most of the experiments including device fabrication, electric, PL and EL measurement, data analysis and theoretical simulation. R.C. contributed to the device fabrication. H.Z. synthesized the graphene samples and GaN substrates. C.W. contributed to the PL measurement. A.Y. contributed to EL measurement. Y.C. performed TEM studies. N.O.W. contributed to the design of the schematic illustrations. X.D. and D.L. co-wrote the paper. All authors discussed the results and commented on the manuscript.

Additional information

Supplementary Information accompanies this paper at http://www.nature.com/naturecommunications

Web End =http://www.nature.com/ http://www.nature.com/naturecommunications

Web End =naturecommunications

Competing nancial interests: The authors declare no competing nancial interests.

Reprints and permission information is available online at http://npg.nature.com/reprintsandpermissions/

Web End =http://npg.nature.com/ http://npg.nature.com/reprintsandpermissions/

Web End =reprintsandpermissions/

How to cite this article: Li, D. et al. Electric-eld-induced strong enhancement of electroluminescence in multilayer molybdenum disulde. Nat. Commun. 6:7509 doi: 10.1038/ncomms8509 (2015).

This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the articles Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/

Web End =http://creativecommons.org/licenses/by/4.0/

8 NATURE COMMUNICATIONS | 6:7509 | DOI: 10.1038/ncomms8509 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications

Word count: 7083

Show less

Abstract

Translate

The layered transition metal dichalcogenides have attracted considerable interest for their unique electronic and optical properties. While the monolayer MoS₂ exhibits a direct bandgap, the multilayer MoS₂ is an indirect bandgap semiconductor and generally optically inactive. Here we report electric-field-induced strong electroluminescence in multilayer MoS₂ . We show that GaN-Al₂ O₃ -MoS₂ and GaN-Al₂ O₃ -MoS₂ -Al₂ O₃ -graphene vertical heterojunctions can be created with excellent rectification behaviour. Electroluminescence studies demonstrate prominent direct bandgap excitonic emission in multilayer MoS₂ over the entire vertical junction area. Importantly, the electroluminescence efficiency observed in multilayer MoS₂ is comparable to or higher than that in monolayers. This strong electroluminescence can be attributed to electric-field-induced carrier redistribution from the lowest energy points (indirect bandgap) to higher energy points (direct bandgap) in k-space. The electric-field-induced electroluminescence is general for other layered materials including WSe₂ and can open up a new pathway towards transition metal dichalcogenide-based optoelectronic devices.

Details

Title

Electric-field-induced strong enhancement of electroluminescence in multilayer molybdenum disulfide

Author

Li, Dehui; Cheng, Rui; Zhou, Hailong; Wang, Chen; Yin, Anxiang; Chen, Yu; Weiss, Nathan O; Huang, Yu; Duan, Xiangfeng

Pages

7509

Publication year

2015

Publication date

Jul 2015

Publisher

Nature Publishing Group

e-ISSN

20411723

Source type

Scholarly Journal

Language of publication

English

DOI

https://doi.org/10.1038/ncomms8509

ProQuest document ID

1692298556

Electric-field-induced strong enhancement of electroluminescence in multilayer molybdenum disulfide

Jump to:

Full Text

Abstract

Details

Suggested sources