Enhanced Conversion Efficiencies in Dye-Sensitized Solar Cells Achieved through Self-Assembled Platinum(II) Metallacages

Abstract

Two-component self-assembly supramolecular coordination complexes with particular photo-physical property, wherein unique donors are combined with a single metal acceptor, can be utilized for many applications including in photo-devices. In this communication, we described the synthesis and characterization of two-component self-assembly supramolecular coordination complexes (SCCs) bearing triazine and porphyrin faces with promising light-harvesting properties. These complexes were obtained from the self-assembly of a 90° Pt(II) acceptor with 2,4,6-tris(4-pyridyl)-1,3,5-triazine (TPyT) or 5,10,15,20-Tetra(4-pyridyl)-21H,23H-porphine (TPyP). The greatly improved conversion efficiencies of the dye-sensitized TiO₂ solar cells were 6.79 and 6.08 respectively, while these SCCs were introduced into the TiO₂ nanoparticle film photoanodes. In addition, the open circuit voltage (Voc) of dye-sensitized solar cells was also increased to 0.769 and 0.768 V, which could be ascribed to the inhibited interfacial charge recombination due to the addition of SCCs.

in Dye-Sensitized Solar Cells Achieved through Self-Assembled Platinum(II) Metallacages

OPEN

R

Zuoli He,, Zhiqiang Hou, Yonglei Xing, Xiaobin Liu, XingtianYin, Meidan Que, Jinyou Shao, Wenxiu Que & Peter J. Stang

Two-component self-assembly supramolecular coordination complexes with particular photo-physical property, wherein unique donors are combined with a single metal acceptor, can be utilized for many applications including in photo-devices. In this communication, we described the synthesis and characterization of two-component self-assembly supramolecular coordination complexes (SCCs) bearing triazine and porphyrin faces with promising light-harvesting properties. These complexes were of the dye-sensitized TiO

into the TiO

charge recombination due to the addition of SCCs.

Due to low cost and highly efficient conversion of photovoltaic energy, numerous research has been studied to improve photovoltaic characteristics as well as inquiry understand the underlying electron-transfer processes in dye-sensitized solar cells (DSSCs) recently15. Usually, the conventional DSSCs consist of the photoanode, the counter electrode, and the liquid electrolyte which oen contains i.e. iodide(I)/tri-iodide(I3) redox couples6,7. The photoanode is usually composed of nanocrystalline semiconductor oxide particle lms, and the counter electrode is usually composed of Pt-coated or other noble-metal coated conducting substrates. In DSSCs, the dye molecules will capture photons from the incident light, and subsequently the photo-generated electrons excited from the dye molecules (such as N719, which is an efficient dye in DSSCs as reported) will be rapidly injected into the conduction band of the semiconductor oxide particle lms photoanode6,7. The electrons are then extracted in the electrolyte and migrated to the counter electrode. During this process, the holes will be captured by iodide ions and transferred to the counter electrode in the oxidized state, i.e., tri-iodide ions. Finally, recombination of the electron and hole will occur together with regeneration of tri-iodide to iodide ions at the counter electrode, thus, resulting in photo-generated current in the closed loop. Base above, the conversion efficiency of a DSSC is determined by three factors, including light-harvesting efficiency, electron injection and collection efficiency8. In recent years, synthetic approaches such as structural modication, surface treatment of mesoscopic oxide lms, and use of sensitizers have been taken to improve the performances of DSSCs912. It can be indicated that the possibilities to increase the surface area of the semiconductor oxide photoanode (so that more dye molecular could be adsorbed directly on the surface of semiconductor oxide nanoparticles lm and simultaneously be reacted with a redox electrolyte directly and eectively) have been successfully attempted. For example, anatase TiO2 NP lm photoanode to enhance interconnection by using a post-treatment with TiCl4 solution or addition a scattering layer were typically used to increase the roughness of the surface and enhance the charge transformation1219.

Electronic Materials Research Laboratory, International Centre for Dielectric Research, Key Laboratory of the Ministry of Education, School of Electronic and Information Engineering, State Key Laboratory for Manufacturing

SCIENTIFIC REPORTS

1

www.nature.com/scientificreports/

Figure 1. (a) Schematic representation of TiO2 NP lm photoanodes with the addition of SCCs (the blue drop is SCCs solution); (b) Design scheme of such SCCs and N719 co-sensitized solar cells.

Several attempts to develop alternative organicinorganic hybrid materials for DSSCs have been made. Such as, Metalorganic frameworks (MOFs) are organicinorganic hybrid materials consisting of an innite exchange, network of metal centers (or inorganic clusters) bridged by organic linkers through metalligand coordination bonds. Sometimes, MOFs have excellent applications in adsorbent, ion conduction, separation, bio-activity and photo-related areas, which may give a chance to introduce into DSSCs2023. Furthermore, for the 3-dimensional network structures of MOFs, their design ability enabling accurate material design based on the diversity of combinations could provide the opportunities to develop new functional structured MOFs. Also, some researchers have introduced unique visible-light-responsive MOFs whose organic linkers act as light-harvesting units into the DSSCs. Kundu et al.24 reported rod-shaped and hexagonal column shaped ZnO microparticles obtained from one-step thermolysis of porous homochiral MOFs. These ZnO microparticles show permanent porosity and visible light emission centered at 605 or 510nm, when used as photoanodes, the conversion efficiency of DSSCs were 0.15% and 0.14%, respectively. Bella et al.25 described the preparation of a polymer composite containing an Mg-MOF through a rapid and environmentally friendly UV-induced free-radical process. Notable solar energy conversion efficiencies were obtained (4.8%), when the composite was used as an electrolyte for DSSCs. Li et al.26

investigated the inuence of coating a TiO2 electrode with MOFs on the performance of DSSCs for the rst time. In this case, its conversion efficiency was improved by 4.5% (from 5.11 to 5.34%), and the enhancement of the open circuit voltage (Voc) of DSSCs was ascribed to retarded interfacial charge recombination. Furthermore, Li et al.27 also reported that a MOF was screen printed on a ZnO electrode thus hierarchical ZnO parallelepipeds were obtained aer calcination, which acts as an eective light scattering layer in dye-sensitized solar cells, leading to signicantly improved solar energy conversion efficiencies (3.67%). Hus et al.28 also fabricated a highly efficient Pt-free dye-sensitized solar cell (DSSC), which its counter electrode was made of cobalt sulde (CoS) nanoparticles synthesized via surfactant-assisted preparation of a MOF, the small size nanoparticles they obtained increased roughness factor and surface area, hence, enhancing interaction with dye molecules. The enhanced Voc

value of the CoS-based DSSCs had greater ll factor value, thus leading to an improved efficiency of 8.1%.

As one knows, the spontaneous formation of metalligand bonds is the basis of a well-established methodology for the construction of supramolecular coordination complexes (SCCs) via coordination-driven self-assembly process. SCCs as another kind of metalorganic complexes encompass discrete systems in which meticulously selected metal centers through self-assembly with ligands containing multiple binding sites oriented with specic angularity to generate a nite supramolecular complex21,29. SCCs can employ rigid organic ligands as structural linkers, and these organic linkers can be usually modied with functional groups that can be meticulously chosen not to interfere with self-assembly process. Once the structures are formed, these functional groups can provide opportunities to impact unique properties that are relative to the functionalized materials21,2935.

That is to say, SCCs with promising light-harvesting or electronic properties will have possibilities to improve the performance of DSSCs36.

Herein, we created a simple model for the application of SCCs in the eld of DSSCs. For the rst time, two SCCs with unique optical properties, which were obtained from the self-assembly of a 90 Pt(II) acceptor with 2,4,6-tris(4-pyridyl)-1,3,5-triazine (TPyT) or 5,10,15,20-Tetra(4-pyridyl)-21H,23H-porphine (TPyP) as reported in our previous research37,38, was dropped on an TiO2 nanoparticle (NP) lm during fabrication of DSSCs as shown in Fig.1a. Therefore, enhanced light-harvesting and unique optical properties of these SCCs from their triazine and porphyrin faces were introduced into the TiO2 nanoparticle (NP) lm photoanodes, thus, resulting in the greatly improved performance in dye-sensitized TiO2 solar cells.

The SCCs with particular photo-physical properties can be utilized for the DSSCs applications in photo-devices. First, we described the synthesis and characterization of cage-like SCCs with promising light-harvesting and unique optical properties. These cages were obtained from the self-assembly of a 90 Pt(II) acceptor with 2,4,6-tris(4-pyridyl)-1,3,5-triazine (TPyT) or 5,10,15,20-Tetra(4-pyridyl)-21H,23H-porphine (TPyP) as shown in Fig.2. All SCCs were characterized by 1H and 31P multinuclear NMR spectroscopy and ESI mass spectrometry (ESI-MS), conrming the structure of each self-assembly and the stoichiometry of the formation. The two-component SCCs 4 were obtained from the self-assembly of the cis-90 Pt(II) acceptor 3 with TPyT donor 1 in a 3:2 ratio in acetone. In the 31P{1H} NMR spectrum of the self-assembly SCCs 4 solution, there is only one intense single peak located at 0.33 ppm with concomitant 195Ptsatellites as shown in Fig.3a. Likewise, the 1H NMR spectrum (Figure S3 in supporting information) shows sharp signals assigned to the coordinated

SCIENTIFIC REPORTS

2

www.nature.com/scientificreports/

Figure 2. Schematic illustration of self-assembly of supra-molecular coordination complexes 4 and 5.

Figure 3. 31P NMR spectra of the discrete [6+4] SCCs 4 and [6+3] SCCs 5.

pyridyl moieties from triazine ( =9.64 ppm, H-Py; =8.94 ppm, H-Py). These 1H NMR spectral results are in accord with the highly symmetric structures of octahedron SCCs 4 bearing triazine faces. ESI mass spectrometry was used here to further conrm the [6+4] self-assembly of 4: concomitant signals are located at m/z =1725.9 ([43OTf]3+), 1257.1 ([44OTf]4+), and 975.9 ([45OTf]5+). By the way, these signal peaks agree well with their theoretical distributions (shown in Figure S4 in supporting information). NMR results indicate that an acetone solution of the self-assembly SCCs 4 has a diusion coefficient of (5.370.13)106cm2/s at room temperature. Both NMR and ESI-MS support the formation of 4 as the dominant product with a yield of 95% in solution is obtained by precipitation using ethyl ether.

The two-component SCCs 5 were also prepared from the self-assembly of the cis-90o Pt(II) acceptor 3 with TPyP donor 2 in a 6:3 ratio in CD2Cl2/CD3NO2 solution. The CD2Cl2 suspension of tetratopic pyridyl ligand 2 was added a CD3NO2 solution of the cis-Pt(PEt3)2(OTf)2 acceptor 3 by dropwise with strong stirring. The reaction solution was stirred at room temperature for 1h and then increased to 70C keeping for overnight. Followed that the solution was evaporated to dryness and the SCCs 5 was collected by precipitation using ethyl ether, in the Yield of 95%. The as-obtained SCCs 5 were also characterized by 31P and 1H multinuclear NMR spectroscopy and ESI mass spectrometry measurements to conrm the formation. In the 31P NMR spectra (Fig.3b), only one intense singlet (0.90ppm) with concomitant 195Ptsatellites could be found. And, the 1H NMR spectra (See Figure S5 in supporting information) show sharp signals assigned to the coordinated pyridyl moieties from porphine (e.g., = 9.75 H-Py, = 8.98 H-Py and HPyrrole, = 8.51 HPyrrole, = 2.32 PCH2CH3). These 1H NMR spectral results

are in accord with the highly symmetric structures of trigonal prism SCCs 5 bearing porphyrin faces. ESI mass spectrometry further conrms the [6+3] self-assembly of 5 (see Figure S6 in supporting information): Signals

SCIENTIFIC REPORTS

3

www.nature.com/scientificreports/

Figure 4. Computational models (MMFF) of (a) the discrete [6+4] SCCs 4 and (b) [6+3] SCCs 5.

Figure 5. Absorption spectra of the as-obtained ligands and SCCs (5105M in DCM).

at m/z = 2966.57 [52OTf]2+, m/z = 1408.99 [54OTf]4+, and m/z) 1097.48 [55OTf]5+. All of these peaks are isotopically resolved and agree well with their theoretical distributions. By the way, a molecular dynamics simulation using Maestro and Macromodel with a MMFF or MM2* force eld at 300K in the gas phase was applied to equilibrate each SCCs, and the output of the simulation was then minimized to full convergence. As shown in Fig.4, models of SCCs 4 and 5 have the shapes of octahedron and tetragonal prisms, respectively.

The UVvis spectra of TPyT, TPyP, cis-Pt(PEt3)2(OTf)2 and SCCs were also measured using a Hitachi U-4100 Spectrophotometer. As shown in Fig.5, The primary characteristic bands of cis-Pt(PEt3)2(OTf)2 were located at 240, 262 and 320nm; the primary characteristic bands of TPyT and TPyP was located at 248 and 415nm, respectively. Aer coordination-driven self-assembly with cis-Pt(PEt3)2(OTf)2, the primary characteristic bands of TPyT show a red shi from 248 to 350 nm in its corresponding SCCs 4, and that of show a little red shi from 415 to 425nm in its corresponding SCCs 5. But it also should be noted, in these two-component SCCs I, the absorbance of main primary characteristic band of cis-Pt(PEt3)2(OTf)2 at 240nm decreased as shown in Fig.5.

The SCCs 4 and 5 solutions were dropped on a TiO2 nanoparticle (NP) lms (The XRD pattern and SEM images of TiO2 nanoparticle NP lms was present in Figures S7 and S8) photoanodes aer being immersed in a 5 104 M N719 dye solution in a mixture of acetonitrile and tert-butanol (1:1, volume ratio of acetonitrile and tert-butanol) for 24h, and the as-obtained photoanodes were then assembled with Pt/FTO used as counter electrodes by using heat-sealing lm, and a liquid electrolyte was injected into interelectrode gap from the holes in counter electrode as shown in Fig.1. The current-voltage (J-V) characteristics of the ligands or SCCs and dye co-sensitized DSSCs were measured under an illumination of AM 1.5 solar simulator of 100mWcm2. The current-voltage (J-V) curves for the as-fabricated DSSCs are shown in Fig.6, also the details of J-V parameters extracted from the J-V curves, such as the open circuit voltage (Voc), Isc, Jsc, Imax, Vmax, Pmax, FF and the conversion efficiency (, calculated according to JscVocFF/(100mWcm2) are presented in Table1. It indicates that the conversion efficiency of N719-sensitized TiO2 solar cells without ligands or SCCs is 4.83%. While co-sensitized with the TPyT and TpyP, the conversion efficiencies of the DSSCs increase to 6.07% and 5.05%, respectively. This enhancement is attributed to the increased Jsc resulting from the enhanced light-harvesting properties of TPyT and TPyP. During the measurement, the open circuit voltage (Voc) will arrive the max aer 20min (Figures S9 and S10 and Table S1 in supporting information, Figure S9 and Table S1 present the details photovoltaic performances of the TPyT/N719 co-sensitized solar cells), which main because inhibited interfacial charge recombination and

SCIENTIFIC REPORTS

4

www.nature.com/scientificreports/

Figure 6. J-V characteristics of the solar cells recorded under AM 1.5G illumination (100mW/cm2) by using ligands or SCCs and dye co-sensitized TiO2 NP lms as photoanodes.

Samples Voc/V Isc/A Jsc/mAcm2 Imax/A Vmax/V Pmax/mW Fill Factor Efficiency

N719 0.732 0.00262 10.5 0.00238 0.507 1.206 63.0 4.83 TPyT/N719 0.733 0.00320 12.8 0.00288 0.527 1.518 64.6 6.09 TPyP/N719 0.716 0.00260 10.4 0.00236 0.534 1.264 67.8 5.05 Pt(II)/N719 0.710 0.00130 5.2 0.00136 0.538 0.733 79.5 2.93 SCCs 4/N719 0.769 0.00330 13.2 0.00297 0.572 1.699 73.5 6.79 SCCs 5/N719 0.768 0.00301 12.0 0.00270 0.563 1.520 65.7 6.08

Table 1. Photovoltaic Performances f Solar Cell with ligands or SCCs and Dye as Photosensitizers.

enhanced electrons transport, which caused by TPyT and TPyP react with I. However, when added the cis-90 Pt(PEt3)2(OTf)2 will react with tert-butylpyridine and break the N719 dye molecular, thus result in the conversion efficiency decreases to 2.93% together with a decrease of Jsc from 10.5 to 5.2mA/cm2. The greatly improved conversion efficiencies of the dye-sensitized TiO2 solar cells are 6.79% and 6.08%, respectively, while the SCCs 4 and 5 are introduced as co-sensitizer with N719 sensitized TiO2 nanoparticle lm photoanodes. Some enhancements could be attributed to enhanced light- harvesting and unique optical properties of these SCCs from their triazine and porphyrin faces as mentioned before. Also the enhanced electrons transport behavior caused by TPyT and TPyP reacted with I, will take an important part. In addition, the open circuit voltage (Voc) of the dye-sensitized solar cells is also increased to 0.769 and 0.768V, which is related to the inhibited interfacial charge recombination due to the introduction of the SCCs9. By the way, it should be mentioned here that the SCCs 4 and SCCs 5 co-sensitized with N719 show a slow reduction rate due to the coordination-driven self-assembly process (Figure S11 in supporting information). When irradiated with the solar light, the temperature will be increased and thus the coordination bond will be broken; the SCCs will be formed again by the coordination-driven self-assembly process when cooling down to room temperature.

Incident photon-to-current conversion efficiency (IPCE) measurements were conducted to analyze the details of the enhanced performance of these ligands or SCCs and dye co-sensitized DSSCs. The IPCE, which corresponds to the external quantum efficiency, is given by

=

IPCE eV nm J

(%) 1240( ) 100

where Jsc (mAcm2) is the short-circuit photocurrent density obtained under monochromatic irradiation and (nm) and (mWcm2) are the wavelength and intensity of the monochromatic light, respectively39. Figure7 shows action spectra of IPCE for DSSCs based on the TiO2 NP lm electrodes (ca. about 10m thickness) sensitized with N719, TPyT/N719, TPyP/N719, Pt(II)/N719, SCCs 4/N719 and SCCs 5/N719, respectively. The IPCE is determined by quantum yield of the electron injection, light absorption efficiency of the dye molecules, and efficiency of collecting the injected electrons at the conducting glass substrate, which is strongly aected by the structure and phys-chemical property of the photoelectrodes14,40. The improved Jsc of the TPyT/N719 and TPyP/

N719 co-sensitized solar cell is due to the enhanced light-harvesting properties of the TPyT and TPyP, which can be seen in the related IPCE spectra between 400700 nm. Contrary to this, an improved IPCE value of the cis-90 Pt(II)/N719, SCCs 4/N719 and SCCs 5/N719 co-sensitized solar cell at short wavelength region as shown in Fig.7b is attributed to the cis-90 Pt(II) accepter, which also indicates that some of SCCs will break down and the cis-90 Pt(II) accepter will exist in the DSSCs aer compared with their absorption spectra. Among these DSSCs, the SCCs 4/N719 and SCCs 5/N719 co-sensitized solar cells show higher IPCE value (reached 55% at 526 nm

sc

SCIENTIFIC REPORTS

5

www.nature.com/scientificreports/

Figure 7. IPCE spectra recorded by using ligands or SCCs and dye co-sensitized TiO2 photoanodes.

and 53% at 515nm, respectively) than that of the TPyT/N719 and TPyP/N719 co-sensitized ones, which results from the enhanced light-harvesting properties of these SCCs from their triazine and porphyrin faces29,36,41,42.

Furthermore, some more reactions mechanism will be needed to research in future.

In summary, we have successfully synthesized two-component self-assembly supramolecular coordination complexes (SCCs) bearing triazine and porphyrin faces with promising light-harvesting properties. When the as-synthesized SCCs were dropped on the TiO2 nanoparticle lm photoanodes, there is a greatly improved conversion efficiency of the as-obtained dye-sensitized TiO2 solar cells, which can be attributed to the enhanced light-harvesting and unique optical properties of the SCCs from their triazine and porphyrin faces. It is also noted that the open circuit voltages (Voc) of the dye-sensitized solar cells increase to 0.769 and 0.768V, which should be related to the inhibited interfacial charge recombination due to the addition of the SCCs. The preliminary results indicate that the SCCs are promising materials for improving the conversion efficiency of DSSCs. We believe that the presented results here will provide a novel approach for improving the photovoltaic properties of DSSCs. Meanwhile, present study may open up a new application eld for SCCs.

Experimental Section

Materials. cis-Pt(PEt3)2(OTf)2 (3) was prepared according to literature procedures43. All other compounds such as 5,10,15,20-Tetra(4-pyridyl)-21H,23H-porphine (TPyP) were bought from Sigma-Aldrich, whereas the solvents were purchased from Cambridge Isotope Laboratory.

18-crown-6 (500 g, 1.9 mmol) and KOH (112.5 mg, 2.0 mmol) were dissolved in 10 mL ethanol and stirred for 20 min. The solution was concentrated to remove solvent under reduced pressure and got an oil product. To this oil, 5 g of 4-cyanopyridine was added. The mixture was heated at 200C. The color changed to red within a short period of time. Aer stirring at this temperature for 6h, the mixture was cooled to room temperature, and then 60mL pyri-dine was added. Stirring the mixture for 5 min gave the ne crystal compound that was ltrated o and washed with pyridine (25mL twice) and toluene (25mL). The pale-red crystals were dissolved in 2mol L1 HCl (60mL). Aer removing small amount solid by ltration, adJusting the solution to slight alkaline using concentrated NH3 aqueous gave a pale-white powder that was ltrated, washed with water, and dried in air to aord 3.5g TPT (yield: 70%), 1H NMR(CD2Cl2): 8.92 (6H), 8.60 (6H).

SCCs 4 was prepared according to literature procedures37. Cis-Pt(PEt3)2(OTf)2 (3) (6.08 mg, 8.34mol) and tripyridyl ligand 1 (1.67mg, 5.35mol) were placed in a 2-gram vial, followed by addition of 0.8mL of acetone-d6, and the vial was then sealed with Teon tape and immersed in an oil bath at 70C for 3h. The [6+4] self-assembly of starting metal-organic supramolecule 4 was obtained, and the solid product was isolated by addition of ethyl ether. Yield: 95% (7.2mg). 1H NMR (acetone-d6, 300MHz) 9.64 (d, J1= 5.1Hz, 24H, H-Py), 8.94 (d, J1= 6.3Hz, 24H, H-Py), 1.96 (m, 72H, PCH2CH3), 1.23 (m, 108H, PCH2CH3). 31P{1H} NMR (acetone-d6, 121.4MHz) 0.33 (s, 195Pt satellites, 1JPt-P= 3085 Hz). MS (ESI) calcd for [M-3OTf]3+ m/z = 1726.0, found 1725.9; calcd for [M-4OTf]4+ m/z = 976.0, found 975.9. Anal. Calcd for C156H228F36N24O36P12Pt6S12(C3H6O)3: C, 34.16; H, 4.27; N, 5.80. Found: C, 34.44; H, 4.56; N, 5.59.

SCCs 4 was prepared according to literature procedures38. 1.2 mL CD2Cl2 suspension of tetratopic pyridyl ligand 2 (2.49 mg, 4.02 mol) was added a 0.4 mL CD3NO2 solution of cis-Pt(PEt3)2(OTf)2(3) (5.89 mg, 8.07 mol) dropwise with continuous stirring (6 min). The reaction mixture was stirred at room temperature for 1 h and then heated to 70 C overnight. The solution was evaporated to dryness, and the product was collected. Yield: 95% (7.96 mg). 1H NMR (CD2Cl2/CD3NO2=3/1, 300MHz) 9.75 (dd, J1=4.8Hz and

J2 =36 Hz, 24H, H-Py), 8.98 (m, 36H, H-Py and HPyrrole), 8.51 (s, 12H, HPyrrole), 2.32 (m, 72H, PCH2CH3), 1.60 (m, 108H, PCH2CH3). 31P{1H} NMR (CD2Cl2/CD3NO2=3/1, 121.4MHz) 0.90 (s, 195Pt satellites, 1JPt-P=3070Hz). MS (ESI) calcd for [M - 2OTf]2+ m/z 2966.54, found 2966.57; calcd for [M-4OTf]4+ m/z 1409.04, found 1408.99;

SCIENTIFIC REPORTS

6

www.nature.com/scientificreports/

calcd for [M-5OTf]5+ m/z 1097.44, found 1097.48. Anal. Calcd for C204H258F36N24O36P12Pt6S12: C, 39.31; H, 4.17; N, 5.39. Found: C, 39.83; H, 4.35; N, 5.16.

Preparation of TiO Viscous TiO2 paste, which was prepared by mixing P25, ethanol, terpinol, and ethyl cellulose, was coated on FTO glass by a screen-printing technique. Then, the as-obtained TiO2 nanoparticle (NP) lm photoanode was immersed into 40 mM TiCl4 aqueous solution at 70C for 30min, which is expected to improve the photovoltaic performances of the devices. Aer this treatment, the photoanode was sintered at 500 C for 30 min. Finally, the as-obtained photoanode was immersed into a 5104M solution of the N719 dye in in a mixture of acetonitrile and tert-butanol (1:1, volume ratio of acetonitrile and tert-butanol) for 24h, and washed with ethanol and dried for next step.

Preparation of Pt/FTO glass counter electrode. The standard Pt/FTO counter electrode was prepared by DC sputtering at 6mA for 10min, and a Pt thin lm of about 20nm thicknesses on a uorine-doped SnO2 glass substrate was prepared.

Assembly of the dye-sensitized solar cells. The DSSC device was composed of the N719 sensitized TiO2 photoanode coupled with the Pt/FTO glass counter electrode. In this step, 2 drops of ligands or SCCs (5mM in Acetone) were used to cover surface of N719 sensitized TiO2 photoanode. The distance between these two electrodes was xed and sealed by heating heat-sealing lm with a thick of 40 m. Then the electrolyte, which contains 0.03 M I2, 0.6 M 1-methyl-3- propylimidazolium iodide (PMII), 0.10M guanidinium thiocyanate, and 0.5M tert-butylpyridine in solutions (15:85 volume ratio of valeronitrile and acetonitrile), was injected into the gap between these two electrodes from one small hole in counter electrode by syring.

Photovoltaic parameters measurements. The power conversion efficiencies of the as-fabricated DSSCs were obtained under 100 mW/cm2 light illumination by a Sol3A all-optical spectrum solar simulator (94043A-type) and the J-V data was collected by the PVIV-1A IV measurement. The incident photon-to-current conversion efficiency of these DSSCs were obtained by QTEST STATION 1000ADX solar cell IPCE test system.

References

1. Bach, U. et al. Solid-state dye-sensitized mesoporous TiO2 solar cells with high photon-to-electron conversion efficiencies. Nature 395, 583585 (1998).

2. Gratzel, M. Solar energy conversion by dye-sensitized photovoltaic cells. Inorg. Chem. 44, 68416851 (2005).3. He, Q. et al. The role of mott-Schottky heterojunctions in Ag-Ag8SnS6 as counter electrodes in dye-sensitized solar cells. ChemSusChem 8, 817820 (2015).

4. Law, M., Greene, L. E., Johnson, J. C., Saykally, R. & Yang, P. Nanowire dye-sensitized solar cells. Nat. Mater. 4, 455459 (2005).5. Zhang, Q., Dandeneau, C. S., Zhou, X. & Cao, G. ZnO nanostructures for dye-sensitized solar cells. Adv. Mater. 21, 40874108 (2009).

6. Jeanbourquin, X. A. et al. Rediscovering a key interface in dye-sensitized solar cells: guanidinium and iodine competition for binding sites at the dye/electrolyte surface. J. Am. Chem. Soc. 136, 72867294 (2014).

7. Robertson, N. Optimizing dyes for dye-sensitized solar cells. Angew. Chem. Int. Ed. 45, 23382345 (2006).8. Javed, H. M. A., Que, W. & He, Z. Anatase TiO2 nanotubes as photoanode for dye-sensitized solar cells. J. Nanosci. Nanotechnol. 14, 10851098 (2014).

9. Nguyen, W. H., Bailie, C. D., Unger, E. L. & McGehee, M. D. Enhancing the hole-conductivity of spiro-OMeTAD without oxygen or lithium salts by using spiro (TFSI)2 in perovskite and dye-sensitized solar cells. J. Am. Chem. Soc. 1099611001 (2014).

10. Chen, H. W. et al. Highly efficient plastic-based quasi-solid-state dye-sensitized solar cells with light-harvesting mesoporous silica nanoparticles gel-electrolyte. J. Power Sources 245, 411417 (2014).

11. Swierk, J. R., McCool, N. S., Saunders, T. P., Barber, G. D. & Mallouk, T. E. Eects of electron trapping and protonation on the efficiency of water-splitting dye-sensitized solar cells. J. Am. Chem. Soc. 136, 1097410982 (2014).

12. He, Z., Que, W., Xing, Y. & Liu, X. Reporting performance in MoS2TiO2 bilayer and heterojunction lms based dye-sensitized photovoltaic devices. J. Alloy. Compd. 672, 481488 (2016).

13. Roy, P., Kim, D., Paramasivam, I. & Schmuki, P. Improved efficiency of TiO2 nanotubes in dye sensitized solar cells by decoration with TiO2 nanoparticles. Electrochem. Commun. 11, 10011004 (2009).

14. He, Z., Que, W., Sun, P. & Ren, J. Double-layer electrode based on TiO2 nanotubes arrays for enhancing photovoltaic properties in dye-sensitized solar cells. ACS Appl. Mater. Interfaces 5, 1277912783 (2013).

15. Lee, S. W., Ahn, K. S., Zhu, K., Neale, N. R. & Frank, A. J. Eects of TiCl4 treatment of nanoporous TiO2 lms on morphology, light harvesting, and charge-carrier dynamics in dye-sensitized solar cells. J. Phys. Chem. C 116, 2128521290 (2012).

16. Koo, H. J. et al. Nano-embossed hollow spherical TiO2 as bifunctional material for high-efficiency dye-sensitized solar cells. Adv. Mater. 20, 195199 (2008).

17. Dong, Z. et al. Quintupleshelled SnO2 hollow microspheres with superior light scattering for highperformance dyesensitized solar cells. Adv. Mater. 26, 905909 (2014).

18. Wu, W. Q. et al. Hydrothermal fabrication of hierarchically anatase TiO2 nanowire arrays on FTO glass for dye-sensitized solar cells. Sci. Rep. 3, 1352 (2013).

19. Sommeling, P. et al. Inuence of a TiCl4 post-treatment on nanocrystalline TiO2 lms in dye-sensitized solar cells. J. Phys. Chem. B 110, 1919119197 (2006).

20. Cook, T. R., Zheng, Y.-R. & Stang, P. J. Metal-organic frameworks and self-assembled supramolecular coordination complexes: comparing and contrasting the design, synthesis, and functionality of metal-organic materials. Chem. Rev. 113, 734777 (2013).21. Yan, D., Tang, Y., Lin, H. & Wang, D. Tunable two-color luminescence and host-guest energy transfer of uorescent chromophores encapsulated in metal-organic frameworks. Sci. Rep. 4, 4337 (2014).

22. Chi, W. S., Roh, D. K., Lee, C. S. & Kim, J. H. A shape-and morphology-controlled metal organic framework template for high-efficiency solid-state dye-sensitized solar cells. J. Mater. Chem. A 3, 2159921608 (2015).

23. Xu, B. et al. Carbazole based hole transport materials for efficient solid-state dye-sensitized solar cells and perovskite solar cells. Adv. Mater. 26, 66296634 (2014).

24. Kundu, T., Sahoo, S. C. & Banerjee, R. Solid-state thermolysis of anion induced metalorganic frameworks to ZnO microparticles with predened morphologies: facile synthesis and solar cell studies. Cryst. Growth Des. 12, 25722578 (2012).

25. Bella, F., Bongiovanni, R., Kumar, R. S., Kulandainathan, M. A. & Stephan, A. M. Light cured networks containing metal organic frameworks as efficient and durable polymer electrolytes for dye-sensitized solar cells. J. Mater. Chem. A 1, 90339036 (2013).

SCIENTIFIC REPORTS

7

www.nature.com/scientificreports/

26. Li, Y., Pang, A., Wang, C. & Wei, M. Metalorganic frameworks: promising materials for improving the open circuit voltage of dyesensitized solar cells. J. Mater. Chem. 21, 1725917264 (2011).

27. Li, Y., Che, Z., Sun, X., Dou, J. & Wei, M. Metal-organic framework derived hierarchical ZnO parallelepipeds as an efficient scattering layer in dye-sensitized solar cells. Chem. Commun. 50, 97699772 (2014).

28. Hsu, S. H. et al. Platinum-free counter electrode comprised of metal-organic-framework (MOF)-derived cobalt sulde nanoparticles for efficient dye-sensitized solar cells (DSSCs). Sci. Rep. 4, 6983 (2014).

29. Shi, Y., Sanchez-Molina, I., Cook, T. R., Cao, C. & Stang, P. J. Synthesis and photophysical studies of self-assembled multicomponent supramolecular coordination prisms bearing porphyrin faces. Proc. Natl. Acad. Sci. USA 111, 93909395 (2014).

30. Cook, T. R. & Stang, P. J. Recent developments in the preparation and chemistry of metallacycles and metallacages via Coordination. Chem. Rev. 115, 70017045 (2015).

31. Yang, H. B. et al. Coordination-driven self-assembly of metallodendrimers possessing well-dened and controllable cavities as cores. J. Am. Chem. Soc. 129, 21202129 (2007).32. Ghosh, K. et al. Synthesis of a new family of hexakisferrocenyl hexagons and their electrochemical behavior. J. Org. Chem. 73, 85538557 (2008).

33. Yang, H. B. et al. A new family of multiferrocene complexes with enhanced control of structure and stoichiometry via coordination-driven self-assembly and their electrochemistry. J. Am. Chem. Soc. 130, 839841 (2008).

34. Pollock, J. B., Cook, T. R. & Stang, P. J. Photophysical and computational investigations of bis(phosphine) organoplatinum(II) metallacycles. J. Am. Chem. Soc. 134, 1060710620 (2012).

35. Pollock, J. B. et al. Photophysical properties of endohedral amine-functionalized bis(phosphine) Pt(II) complexes as models for emissive metallacycles. Inorg. Chem. 52, 92549265 (2013).

36. Mathew, S. et al. Dye-sensitized solar cells with 13% efficiency achieved through the molecular engineering of porphyrin sensitizers. Nat. Chem. 6, 242247 (2014).

37. Zheng, Y. R., Lan, W. J., Wang, M., Cook, T. R. & Stang, P. J. Designed post-self-assembly structural and functional modications of a truncated tetrahedron. J. Am. Chem. Soc. 133, 1704517055 (2011).

38. Zheng, Y. R. et al. A facile approach toward multicomponent supramolecular structures: selective self-assembly via charge separation. J. Am. Chem. Soc. 132, 1687316882 (2010).

39. Hara, K. et al. Nanocrystalline electrodes based on nanoporous-walled WO3 nanotubes for organic-dye-sensitized solar cells. Langmuir 27, 1273012736 (2011).

40. Hao, Y. et al. Efficient semiconductor-sensitized solar cells based on poly (3-hexylthiophene)@ CdSe@ ZnO core shell nanorod arrays. J. Phys. Chem. C 114, 86228625 (2010).

41. Panda, M. K., Ladomenou, K. & Coutsolelos, A. G. Porphyrins in bio-inspired transformations: Light-harvesting to solar cell. Coord. Chem. Rev. 256, 26012627 (2012).

42. DSouza, F. et al. Spectroscopic, electrochemical, and photochemical studies of self-assembled via axial coordination zinc porphyrinfulleropyrrolidine dyads. J. Phys. Chem. A 106, 32433252 (2002).

43. Stang, P. J., Cao, D. H., Saito, S. & Arif, A. M. Self-assembly of cationic, tetranuclear, Pt (II) and Pd (II) macrocyclic squares. X-ray crystal structure of [Pt2+ (dppp)(4, 4-bipyridyl). cntdot. 2-OSO2CF3]4. J. Am. Chem. Soc. 117, 62736283 (1995).

Acknowledgements

Z.L.H. and W.X.Q. thank PhD Mobility Program of Xian Jiaotong University, the 111 Project of China (B14040) and the Fundamental Research Funds for the Central Universities. W.X.Q. thanks the Research Fund for the Doctoral Program of Higher Education of China (20120201130004), the Science and Technology Developing Project of Shaanxi Province (2015KW-001). W.X.Q. and J.Y.S. also thank the National Natural Science Foundation of China Major Research Plan on Nanomanufacturing (91323303) for nancial support. P.J.S. acknowledges funding by the National Sciences Foundation (1212799).

Author Contributions

Z.L.H., W.X.Q. and P.J.S. designed the experiments; Z.L.H. conducted all field experiments. Z.Q.H. and X.T.Y. participated in part of the measurements of the dye-sensitized solar cells; Y.L.X., X.B.L., M.D.Q. and J.Y.S. participated in part in characterization of TiO2 nanoparticle (NP) lm photoanode and assembly of the dye-sensitized solar cells; W.X.Q., J.Y.S. and P.J.S. supervised the project; Z.L.H., W.X.Q. and P.J.S. analyzed the data and wrote the manuscript. All authors discussed the results and commented on the manuscript.

Additional Information

Supplementary information accompanies this paper at http://www.nature.com/srep

Competing nancial interests: The authors declare no competing nancial interests.

How to cite this article: He, Z. et al. Enhanced Conversion Efficiencies in Dye-Sensitized Solar Cells Achieved through Self-Assembled Platinum(II) Metallacages. Sci. Rep. 6, 29476; doi: 10.1038/srep29476 (2016).

This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the articles Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/

SCIENTIFIC REPORTS

8