1. Introduction
The use of plastics has increased exponentially in different sectors that affect our daily lives, such as packaging, building, automotive, medical devices, etc. This trend is the result of the good properties of this material, such as its flexibility, lightness, or strength in addition to its simple and productive manufacturing process [1]. However, different characteristics are required for each application and can be changed by switching the component materials. Therefore, the characteristics of plastic can be adjusted for the intended application. The main problem is that plastics are used only for a short period or even just one time, and after that are discarded. If not properly collected, this waste is deposited and accumulates in the environment, contaminating the different ecosystems of all living beings. According to the report data, global plastic production reached 367 million tons in 2020, of which 55 million tons were produced in Europe [2]. On the other hand, only 29 million tons of plastic residue were recovered, corresponding to recycling of only 34.6%. The remainder was used to recover energy (42%) or disposed of in landfill (23.4%) [2]. Consequently, a wide variety of studies are centered on the search for renewable materials with properties similar to plastic but that can be degraded easily after use, thus helping to reduce environmental contamination.
Bioplastics represent an environmentally friendly alternative to plastic. They have the advantage of being biobased, biodegradable or both, which means that they are a product obtained from biomass (biobased) and/or they can be degraded by microorganisms into water and CO2 (biodegradable) [3]. Thus, bioplastics are classified according to these properties (Figure 1): biobased and non-biodegradable, biobased and biodegradable or fossil-based and biodegradable.
The most studied examples are polylactic acid (PLA) and PHAs, as they are biobased and biodegradable bioplastics. PLA is a polymer composed of lactic acid (LA) monomers and qualifies as a linear aliphatic thermoplastic polyester [5]. LA molecules contain chiral carbon, for which there are two isomeric forms: L (+) lactic acid and D (−) lactic acid. The properties of PLA can change according to the proportion of L-LA to D-LA. PLA can be used in different areas of our lives such as in medical devices, 3D printers or food packaging [6,7,8,9]. LA can be obtained by chemical synthesis or through fermentation. However, fermentation is usually preferred, as it can produce optical pure isomers of LA instead of a racemic mixture of L-LA and D-LA [5]. Through the fermentation pathway, LA is produced from sugars, mainly glucose, by lactic acid bacteria (LAB) through three different metabolic pathways, which influence the required carbon source and the obtained LA yield.
On the other hand, PHAs are a polymer classified as polyesters consisting of units of (R)-hydroxy fatty acid linked by ester bonds [10]. PHAs are generated by some microorganisms, in which they accumulate when the microorganism is under stress due to a lack of nutrients [11]. Various strategies have been studied to induce the accumulation of PHAs inside cells, for instance via limitation of the nitrogen source or oxygen concentration in fermentation using pure cultures. On the other hand, continuous cycles of fest and famine can be used in mixed cultures to select microorganisms able to accumulate PHAs. To date, more than 150 different monomers have been identified, and they can be combined to modify or improve the properties of the bioplastic. In general, they provide excellent benefits, including 100% biodegradability, biocompatibility, non-toxicity and antioxidant and immunotolerant properties [12]. As in the case of PLA, the bioplastic PHA has multiple uses, such as in packaging, coatings, and pharmaceutical and medical applications [13].
These bioplastics have many benefits over petroleum-based plastics. However, the biggest drawback is their production cost, which is 3 to 4 times higher. Different ways of reducing this cost are currently being studied, one of which is through using cheaper raw materials as alternatives [14]. Bioplastics are usually produced from pure sugars or fatty acids and, in some cases, also from first-generation raw materials such as corn or sugarcane [15]. Although high yields are obtained, the use of edible raw materials for bioplastic production raises concerns about food prices and quantity. As an alternative, second-generation feedstocks, such as agriculture or food industry residues, can also be used. These materials do not compete with human food, are found in abundance and are inexpensive. An additional advantage of these materials is they help to reduce the problems associated with the treatment of these wastes.
The majority of second-generation feedstocks are classified as lignocellulosic biomass (LCB) because they are mainly composed of cellulose, hemicellulose and lignin [16,17]. LCB is considered the largest renewable source on Earth [18]. The composition of this biomass depends on its source, but they are generally composed of 35–50% cellulose, 20–35% hemicellulose and 10–25% lignin [19]. As seen in Figure 2, the typical lignocellulose structure is composed of a matrix of crystalline cellulose surrounded by hemicellulose, pectin and lignin polymers [19]. This structure prevents the degradation of cellulose and confers rigidity to cell wall plants and, thus, resistance against insects and pathogens [20].
Sugar beet pulp (SBP) is a lignocellulosic by-product of the sugar industry that has traditionally been used for animal feed [22]. However, it has also been used as raw material to produce a wide range of value-added products, such as LA or PHAs, through biotechnological processes. In this review, each of the main stages involved in the production of bioplastics from this by-product are studied in detail (Figure 3). In this way, an evaluation of the different pretreatments applied to SBP to facilitate the subsequent enzymatic hydrolysis has been made. In addition, the influence of the enzymatic cocktail used for the hydrolysis of the biomass is analyzed. Regarding this, and with the aim of reducing the cost of processing the sugar beet pulp, enzymes are sometimes produced directly on the biomass via solid-state fermentation. This novel aspect is also described in detail in the review. Finally, the different strategies used to increase the yield of lactic acid and polyhydroxyalkanoates from SBP hydrolysates will be compared.
2. Exhausted Sugar Beet Pulp as a Renewable Feedstock
Sugar beet (Beta vulgaris L.) is one of the main sugar crops, along with sugarcane, used to produce sucrose for human consumption. As one of the main sugar crops, sugar beet accounts for about 20% of global sugar production, with sugarcane making up the remaining 80% [22]. This crop thrives in moderate-temperature regions in the northern hemisphere, where the climate is suited to its growth and development. The top sugar beet producers in the world in 2021 were the European Union (112,847.63 tons), the Russian Federation (47,500 tons), and the United States (32,364.15 tons) [23].
The sugar content of sugar beet can vary from 12% to 20%, making it a valuable raw material. The sugar industry can also achieve a financial gain of up to 10% through the use of by-products generated during production. The three main by-products are beet pulp, lime sludge and molasses, which can be used as renewable materials to produce energy or other value-added products [22]. For instance, one ton of sugar beet yields 160 kg of sugar, 500 kg of wet exhausted pulp and 38 kg of molasses [24] (see Figure 4A).
2.1. Processing of Sugar Beet
The diagram in Figure 5 shows the steps for producing white sugar from sugar beets. Sugar beetroots, or taproots, are harvested mechanically, separating the leaves from the bulbs. The bulbs are washed, and the washing sludge is decanted to reuse the water [25]. The roots are then cut into thin strips, called cossettes, which are moved to stainless steel tanks, called diffusers, where they are mixed with hot water (55–75 °C) at a solid/liquid ratio (SLR) of 1:2 w/w with residence times from 1 to 2 h [22]. The juice obtained, called raw juice, contains mainly sucrose, but other compounds also that have been extracted from the root can hinder the crystallization of sugar. For this reason, the raw juice is purified before crystallization, with calco-carbonic treatment being the most commonly used approach [26,27]. The clean juice obtained after this step, the thin juice, is concentrated with multi-effect evaporators to obtain the final juice (thick juice) [28]. Finally, the thick juice is introduced into the crystallizers, where sugar is produced through crystallization [29,30]. Crystals are later separated from the liquid by centrifugation, dried in continuous rotary dryers and sieved [22]. The residual liquid stream, called molasses, contains 50% w/w sugars and other substances, such as oligosaccharides and organic acid salts.
The remaining pulp obtained after the diffusion step, named exhausted SBP, is pressed, and the retained juice is recovered. The pulp then contains a humidity of 70% and can be conformed into pellets of approximately 5 cm in length and 0.5 cm in diameter by extrusion [31]. These pellets are preserved by drying to reach a final humidity lower than 10%.
SBP is commonly used as animal feed. However, it has been also used as a raw material for the extraction of pectin and phenolic compounds and for producing several value-added products (VAPs), such as biogas by anaerobic digestion, hydrogen by acidogenic fermentation, or hydrolysates rich in sugars that can be fermented into several bioproducts such as ethanol, lactic acid, succinic acid or polyhydroxyalkanoates, among others. The digestate from the anaerobic digestion of SBB has also been used as an organic fertilizer in agriculture [32,33,34].
2.2. Chemical Composition of SBP
SBP contains between 87 and 92% of dried matter [35] and is mainly composed of 24–32% of hemicelluloses, 22–30% cellulose, 15–32% pectin, 1–2% lignin, 7–8% protein, 7.5–12% minerals and 1–2% fats [36,37,38] (see Figure 4B). The pulp composition can vary depending on the process of sugar extraction, the degree of maturation of the root and the sugar beetroot’s geographical origin.
Among the sugar industry effluents, beet pulp stands out as a material rich in carbon sources [39]. Hence, component sugars from chemically or enzymatically hydrolyzed polysaccharides from SBP are appropriate raw materials for fermentation. There are several papers reporting on the total sugar composition of SBP after complete hydrolysis as being D-glucose (21–26%), D-galacturonic acid (14–21%) and L-arabinose (21–23%) the majority. The next highest sugar contents were D-galactose (5–6%), L-rhamnose (2.5%), D-xylose (about 2%) and mannose (1%) [40].
In a recent study comparing different agri-food wastes for biopolymer production, the feedstock quality was determined based on having high cellulose and low moisture and lignin content. Low moisture and lignin contents mean lower energy requirements for drying and easier processing, respectively. The residues generated in the harvest and processing stages of the food supply chain of wheat, barley, oats, rapeseed, sugar beet, carrots and onions were analyzed, and the percentage of moisture, cellulose, and lignin ranged from 7–87%, 10–42%, and 2–39%, respectively. Although sugar beet pulp has medium-high cellulose content (around 32%), it showed the lowest lignin (less than 5%). Regarding moisture content, vegetable wastes had a much higher percentage, between 77 and 87%, compared to the cereal residues (less than 20%). However, other factors such as the annual production, seasonality and feedstock cost should be taken into account [41].
3. Production of Bioplastic Precursors from Sugar Beet Pulp
The production of bioplastics, such as PLA and PHAs from SBP, can be performed through a biotechnological process such as the one proposed in Figure 3, which is most applied in the valorization of lignocellulosic biomass. Usually, the biomass is pretreated to enable access to the enzymes used in the saccharification step, where the biomass is hydrolyzed to produce a medium rich in sugars. This medium can be fermented to produce LA or PHAs, which are the precursor molecules to produce PLA and PHAs, respectively.
3.1. Pretreatments Applied to Sugar Beet Pulp
Pretreatment is an important step in the valorization of biomass because it helps to separate lignin and hemicellulose structures from cellulose. In this way, enzymes have easier access to cellulose [42,43]. Depending on the working principle, the pretreatments can be classified as physical, chemical, physicochemical and biological pretreatments [44].
The aim of physical pretreatment is to increase the surface area of the biomass particles. This can be achieved by reducing the particle size with mechanical comminution. Thus, the crystallinity of the cellulose structure is also damaged, which facilitates enzyme accessibility [44,45].
The results achieved with chemical pretreatments will depend on the reagent added, its concentration and the pretreatment duration. Thus, alkalis, such as sodium or potassium hydroxides, are used with the intention to solubilize lignin and hemicellulose [46]. On the other hand, acids, such as sulfuric or hydrochloric acids, are more efficient in degrading only hemicellulose [45]. Moreover, oxidant agents such as alkaline hydrogen peroxide or organic acids are chosen to degrade lignin [42].
Physicochemical pretreatments attempt to solubilize hemicellulose and lignin by changing the temperature, pH and moisture of the biomass [42]. In this way, pretreatments such as steam explosion, ammonia fiber explosion (AFEX), wet oxidation, CO2 explosion and thermal (liquid hot water) treatment can be performed, where high-temperature exposure is usually combined with high pressure [47].
Biological pretreatments degrade part of the biomass structure by the action of microorganisms [42]. Usually, this is performed using fungi because they can more easily penetrate solids. In this pretreatment, not only might hemicellulose and lignin be degraded but part of the cellulose may also be consumed by the microorganism [45].
Most pretreatments applied to SBP are diluted acid and thermal pretreatment, which produce the highest hydrolysis yields. Other studied SBP pretreatments include size reduction (milling), ultrasound, steam explosion, ensiling and solid-state fermentation, which are all summarized in Table 1. For example, ultrasound pretreatment was applied on SBP using SONOPULS HD 2200 homogenizer in continuous mode with 400 W for 20 min [24]. However, the hydrolysis yield did not increase. On the other hand, for thermal pretreatment of SBP, the hydrolysis yield was increased from 0.70 to 0.85 g of reducing sugars per gram of SBP (gRS/gSBP) [24]. This pretreatment was carried out in an autoclave at 120 °C for 30 or 60 min [24]. Another study performed by Rezic et al. also focused on the effect of these pretreatments on SBP, and similar results were obtained [24,48]. In this case, thermal pretreatment was performed in the autoclave for 20 min, and ultrasound pretreatment was carried out at 200 W for 5 to 45 min [48].
Several authors have studied the effect of diluted acid pretreatment on SBP, resulting in the solubilization of pectin and hemicellulose fractions [50]. For instance, SBP was pretreated with sulfuric acid (1.1% w/w) at 150 °C for 10 min and solid loading of 10% w/w, and the hydrolysis yield reached 0.82 gRS/gSBP [49]. However, this yield can be improved to 0.86 gRS/gSBP by performing the pretreatment at the optimal conditions found by El-gendy et al. of 120 °C, 0.1 N HCl, 14% w/w of solid loading and 6 min [50]. Nonetheless, a higher hydrolysis yield (0.92 gRS/gSBP) was achieved when SBP was pretreated with sulfuric acid (0.66%) with a solid loading of 6% at 120 °C [51]. More recently, Marzo et al. performed diluted acid pretreatment on SBP, studying the effect of sulfuric acid concentrations of 0.25, 0.5, or 1% w/v [52]. The pretreatment was performed by soaking the solid at a solid/liquid ratio of 1:20 (w/v) with a solution of sulfuric acid and autoclaving the mixture at 120 °C for 20 min. The results showed an increase in the production of glucose as the concentration of acid was increased, reaching a hydrolysis yield of 0.45 gRS/gSBP.
Another lesser-studied pretreatment is the steam explosion. The optimum conditions of pressure and pretreatment time found by Cárdenas–Fernández et al. were 5.3 bar and 24.4 min [54]. With this pretreatment, solubilization of both pectin and the insoluble cellulose fraction was achieved, thereby increasing the ethanol yield due to the increased solubilization of cellulose.
Biological pretreatments such as ensiling or solid-state fermentation have been also studied for SBP. For instance, SBP was pretreated using the ensiling methodology, where several Lactobacillus species were involved [53]. This increased the enzymatic digestibility of SBP by 35% [53]. In this case, the microorganism degraded some fraction of the biomass. As this technique is usually employed for long-term storage of biomass, it seems an interesting option to stabilize SBP and pretreat it at the same time. Additionally, SBP was also pretreated via solid-state fermentation [52]. Fermentation was carried out with the fungus Aspergillus awamori at 70% moisture content and incubation at 30 °C for 5 days. The results obtained after the enzymatic hydrolysis of the pretreated SBP showed a decrease in the concentration of total reducing sugars produced compared with the non-pretreated solid. However, the same glucose concentration was obtained, showing that only the hemicellulose and pectin content has been removed by the fungus.
3.2. Enzymatic Hydrolysis of SBP
The production of sugars from SBP can be performed through acid or enzymatic hydrolysis. Acid hydrolysis is carried out with concentrated or diluted acids such as hydrochloric acid or sulfuric acid, which degrade the lignocellulose structure [19]. Although a pretreatment step before acid hydrolysis is not necessary, this step has numerous disadvantages compared to enzymatic hydrolysis. For example, a special material is required for the equipment used in this type of hydrolysis to ensure it can resist the corrosion resulting from the acids [19]. However, one of the main issues of this process is the production of compounds that are inhibitory for the microorganisms, such as furfural or its derivates, which are generated after the degradation of sugars due to acidic conditions. On the other hand, enzymatic hydrolysis is a more environmentally friendly process.
Enzymatic hydrolysis is based on the use of hydrolytic enzymes that hydrolyze the lignocellulose structure into simple sugars. There is a wide variety of enzymes that are necessary to hydrolyze the whole biomass, with the most important being cellulases, hemicellulases and pectinases [55]. The proportion of each will depend on the composition of the biomass that is hydrolyzed. One of the main advantages of enzymatic hydrolysis is the use of mild conditions for temperature (45–50 °C) and pH (4.8–5.0) [56]. Moreover, inhibitory compounds are not generated, and the equipment is not damaged by corrosion. On the other hand, the main problem of enzymatic hydrolysis is the high cost of enzymes and the occasional need for prior pretreatment.
Several authors have studied the enzymatic hydrolysis of SBP with the aim of maximizing sugar production from SBP (Table 2). Some of them studied the influence of the enzymatic cocktail. In this sense, the main enzymes used are commercial cocktails composed of a mixture of cellulase, xylanase and pectinase. The optimum conditions of these cocktails are very similar; thus, the hydrolysis of SBP is generally performed at 50 °C, pH 4.8, 150 rpm and 2% w/w of solid loading (Table 2). One of the main cocktails used is called “Celluclast® 1.5 L”, and it is added to correspond to enzyme activity in the range of 4–30 filter paper units per gram of dry matter (FPU/g). Depending on the added enzyme activity, the hydrolysis yield can be improved from 0.27 to 0.49 gRS/gSBP when the cellulase activity is increased from 5 to 30 FPU/g [57]. However, other cellulase cocktails richer in cellobiase, xylanase or pectinase, such as Novozyme 188, Novozyme 431, Viscozyme L, Pectinex®, Celustar XL or Agropect pomace, can be also used. For example, the hydrolysis yield was increased from 0.15 to 0.70 gRS/gSBP when a cocktail combining cellulase and cellobiase was supplemented with hemicellulases and pectinases [58]. Due to the composition of SBP, the addition of these enzymes solubilizes the fraction of hemicellulose and pectin, making cellulose more accessible to enzymes.
Other authors focused their studies on the pretreatment of SBP to improve the enzymatic hydrolysis yield. For example, the hydrolysis yield was increased from 0.15 to 0.5 gRS/gSBP when SBP was pretreated with ammonia (0.5 mL/g of ammonia, 80 °C, 5 min) and the enzymatic hydrolysis was performed with cellulase and cellobiase [58]. However, the hydrolysis yield decreased from 0.7 to 0.61 gRS/gSBP when SBP was pretreated in the same conditions but the hydrolysis was carried out with cellulase, cellobiase, hemicellulase and pectinase [58]. The hydrolysis yield was also increased from 0.2 gRS/gSBP for non-pretreated SBP to 0.48 and 0.38 gRS/gSBP when SBP was pretreated with thermal and chemical pretreatment with hydrochloric acid, respectively [59]. The same effect was observed in other papers, where the hydrolysis yield was increased from 0.18 gRS/gSBP for non-pretreated SBP to 0.38, 0.49, 0.23 and 0.25 gRS/gSBP, when hydrochloric acid, ammonia, pectinase or ammonium oxalate was added to pretreat SBP [60].
3.3. Enzyme Production by Solid-State Fermentation
Enzymatic hydrolysis is the stage of the process that most influences the overall cost of the process, due to the high cost of the enzymes. To render the process more profitable, various approaches have been explored, such as looking for new sources of enzymes or alternative techniques to submerged fermentation [61]. One such technique is the production of hydrolytic enzymes by solid-state fermentation (SSF) [62,63]. The advantage of this fermentation is that different types of biomass, such as agri-food industry wastes or bioproducts, can be used as raw material, acting as a source of carbon and nutrients and as solid support for fungal growth and enzyme production [64].
SSF is a heterogeneous fermentation that takes place in the absence or near absence of visible water between particles [65]. It is usually carried out by filamentous fungi that grow on the surface of the solid due to their ability to colonize the interparticle spaces of porous materials [66], although bacteria and yeasts can also be used. Most fungal species employed for this technique belong to the genera Aspergillus, Pleurotus and Trichoderma [67].
SSF is a complex process where parameters such as temperature, aeration rate, pH, initial moisture, particle size, agitation, water activity or inoculum concentration should be optimized, and most will depend on the microorganism selected to produce the enzymes [68]. Depending on the fungal species, the optimum temperature for growth can vary from 20 to 55 °C, while the optimum moisture content can change in the range of 40 and 70% [69]. However, the pH is usually adjusted to 5 [70], and aeration is mainly used in pilot-scale reactors [71].
Table 2Conditions for enzymatic hydrolysis of SBP. T: temperature; SL: solid loading; EA: enzyme activity; YH: hydrolysis yield (gRS/gSBP).
| Reference | T | pH | Agitation | SL | Enzyme Type 1 | EA 2 | Pretreatment | YH |
|---|---|---|---|---|---|---|---|---|
| [58] | 40 °C | 4.8 | - | 5% w/w | Celluclast® 1.5 L |
4.2 FPU/g d.m. |
Ammonia |
0.50 g/g |
| 40 °C | 4.8 | - | 5% w/w | Celluclast® 1.5 L |
4.2 FPU/g d.m. |
Ammonia |
0.61 g/g | |
| 40 °C | 4.8 | - | 5% w/w | Celluclast® 1.5 L |
4.2 FPU/g d.m. |
Untreated | 0.15 g/g | |
| 40 °C | 4.8 | - | 5% w/w | Celluclast® 1.5 L |
4.2 FPU/g d.m. |
Untreated | 0.70 g/g | |
| [53] | 50 °C | 4.8 | 150 rpm | 2% w/w | Celluclast® 1.5 L |
15 FPU/g d.m.15 CBU/g d.m. | Ensilage |
0.19 g/g |
| [57] | 40 °C | 4.8 | 150 rpm | 2.5% w/w | Celluclast® 1.5 L | 5 FPU/g d.m. | HCl pH 1.5, 85 °C, 4 h | 0.27 g/g |
| 40 °C | 4.8 | 150 rpm | 2.5% w/w | Celluclast® 1.5 L | 30 FPU/g d.m. | HCl pH 1.5, 85 °C, 4 h | 0.49 g/g | |
| [72] | 50 °C | 5 | - | 10% w/w | Celustar XL |
0.75 FPU/g d.m. | Untreated | 0.3 g/g |
| [51] | 50 °C | 4.8 | 150 rpm | 2% w/w | Celluclast® 1.5 L |
15 FPU/g d.m. |
Diluted acid H2SO4, 0.66%, |
0.63 g/g |
| [59] | 45 °C | 4.8 | - | 2% w/w | Celluclast® 1.5 L | 20 FPU/g d.m. | Untreated | 0.20 g/g |
| 45 °C | 4.8 | - | 2% w/w | Celluclast® 1.5 L | 20 FPU/g d.m. | HCl pH 1.5, 85 °C, 4 h | 0.38 g/g | |
| 45 °C | 4.8 | - | 2% w/w | Celluclast® 1.5 L | 20 FPU/g d.m. | Autoclave |
0.44 g/g | |
| [60] | 50 °C | 4.8 | - | 5% w/w | Cellulase | 20 FPU/g d.m. | Untreated | 0.18 g/g |
| 50 °C | 4.8 | - | 5% w/w | Cellulase | 20 FPU/g d.m. | HCl 1% w/w, 80 °C, 6 h | 0.38 g/g | |
| 50 °C | 4.8 | - | 5% w/w | Cellulase | 20 FPU/g d.m. | Ammonia |
0.49 g/g | |
| 50 °C | 4.8 | - | 5% w/w | Cellulase | 20 FPU/g d.m. | Pectinase 30 U/g, 50 °C, 6 h | 0.23 g/g | |
| 50 °C | 4.8 | - | 5% w/w | Cellulase | 20 FPU/g d.m. | Ammonium oxalate |
0.25 g/g | |
| [73] | 50 °C | 5.0 | 150 rpm | 10% w/w | Celluclast® 1.5 L |
2200 FPU/g d.m. |
Autoclave 120 °C, 20 min | 0.71 g/g |
1 Novozyme 188: Cellobiase; Novozyme 431: Cellobiase; Pectinex®: Pectinase; Agropect pomace: Pectinase; Celluclast® 1.5L: Cellulase, xylanase, pectinase, mannanase; Viscozyme L: arabinase, cellulase, β-glucanase, hemicellulase and xylanase; Cellustar XL: xylanase, cellulase, β-glucanase. 2 FPU: filter paper cellulase unit; CBU: cellobiase activity units; PGU: polygalacturonase activity units; HU: hemicellulase activity units; d.m: dry matter.
A noteworthy substrate for this process is lignocellulosic biomass due to its rich composition of cellulose, hemicellulose and pectin. This type of substrate can induce the production of different enzymes by fungi [65,74]. In this sense, SBP seems to be a suitable substrate to produce hydrolytic enzymes. For instance, hydrolytic enzymes, such as xylanase, exo-polygalacturonase and cellulase, were produced via SSF of SBP, reaching 35 U/g of xylanase and 28 U/g of exo-polygalacturonase after 8 days of fermentation with Aspergillus awamori [75]. These values were higher than those for production from orange peel waste under the same conditions [75]. Dextranase was also produced by SSF of SBP, reaching peak activity (1057 U/g) after three days of growth of A. awamori F-234 [76]. This result was obtained in a study where various residues, such as olive mill solid waste, jojoba mill solid waste and sugar cane bagasse, and different fungi strains, such as Aspergillus niger F-93, Aspergillus fumigatus F-993, Penicillium funiculosum NRC289, Trichoderma koningii F-25 and Aspergillus awamori F-234, were tested. However, SBP was also studied in combination with other residues such as wheat bran [77]. The results showed that the enzyme production depended on the medium and the fermentation conditions and that polygalacturonase production was induced when wheat bran was mixed with 30% of SBP, reaching 909 U/g with A. sojae ATCC 20235 after 8 days at 30 °C [77].
Other studies were performed to increase enzyme production by adding extra nitrogen sources to the raw material. For example, wastewater from monosodium glutamate production was added as a nitrogen and water source to improve pectinase production from the fermentation of SBP with Aspergillus niger (CGMCC0455) [78]. Thus, the enzyme activities were increased achieving 15.6 × 10−3 U/g of endopectinase, 3.6 × 10−3 U/g of polygalacturonase and 16 × 10−3 U/g of pectin-lyase [78]. Ammonium sulfate was also tested as a nitrogen source on the production of α-L-arabinofuranosidase by SSF of SBP with Trichoderma reesei, reaching 433 U/g of α-L-arabinofuranosidase [79].
To conclude, SSF is a flexible process that can be adapted to produce a wide range of hydrolytic enzymes. However, enzymes are usually extracted and purified to be used in enzymatic hydrolysis, which also raises the overall cost of the process. As an alternative process, some authors have studied the addition of fermented solid directly to the medium to be hydrolyzed, avoiding the enzyme extraction step. Leung et al. were one of the first to propose this process in the SSF of waste bread [80]. They produced protease and glucoamylase by SSF of waste bread and, subsequently, the fermented solid was added to fresh waste bread to produce a hydrolysate, which then was fermented to succinic acid. The same strategy was followed by other authors, such as Pleissner et al., Kwan et al. or Dessie et al., for different wastes, such as food waste, bakery waste, and fruit and vegetable waste [81,82,83]. More recently, Marzo et al. used the same strategy on SBP, where the enzymes were produced through the SSF of SBP and then added to fresh SBP to produce a hydrolysate rich in sugars [84]. The hydrolysis yield was increased from 0.45 to 0.55 gRS/gSBP when a fed-batch strategy was applied. Thus, 15 g of fermented solid and 13.75 g of fresh solid were mixed at the beginning of the hydrolysis, and then the same amount of fresh solid was added 3 times every 2.5 h [84].
3.4. Lactic Acid Fermentation
The medium obtained after enzymatic hydrolysis has a high content of sugars, such as glucose. Therefore, it can be a raw material to produce a wide variety of VAPs through submerged fermentation. LA is a common product obtained through the fermentation of sugars and is commonly used in cosmetic formulations and in the food and pharmaceutical industries. For example, in the food industry, it is used as a flavor-enhancing agent and acidifier [85,86,87]; in cosmetics formulations, it is added for its emulsifying properties and the moisturizing effects produced on the skin; and in the pharmaceutical industry, it is used for the synthesis of dermatologic products and drugs against osteoporosis [88]. Additionally, LA has recently received special attention for being the precursor of PLA, a bio-degradable and bio-based bioplastic [89]. It is also considered a platform chemical to produce different products, such as acrylic acid, pyruvic acid, ethyl-lactate, 2,3-pentanedione, acetaldehyde and propylene glycol [90].
3.4.1. Metabolic Pathways to Produce LA via Fermentation
LA can be produced by a wide variety of microorganisms such as bacteria, fungi, yeast, cyanobacteria or algae [14]. However, the most studied are LAB, which includes genera such as Carnobacterium, Enterococcus, Lactobacillus, Lactococcus, Leuconostoc, Oenococcus, Pediococcus, Streptococcus, Tetragenococcus, Vagococcus and Weissellla [91]. These LAB require the optimum conditions of temperature (30–45 °C) and pH (6–7) to grow and produce LA [92]. They also require the proper amount of nitrogen, vitamins and minerals for optimal growth. These nutrients may be contained in the hydrolysate obtained from agri-food waste, but they are usually supplemented in the medium. For instance, yeast extract is one of the most used nitrogen sources, however, its supplementation in the hydrolysates increases the total cost of the LA production process [93].
LAB are classified as homofermentative, heterofermentative or facultative heterofermentative, according to the metabolic pathways used to produce LA. Thus, the conversion of sugars to LA by LAB is produced through three different pathways (Figure 5): the Embden–Meyerhof–Parnas (EMP) pathway, the pentose phosphate (PP) pathway and the phosphoketolase (PK) pathway [88].
Homofermentative LAB ferment hexoses via the EMP pathway, producing theoretically 2 mol of LA per mol of glucose. In addition, some strains also convert glucose via the PP pathway instead of the EMP pathway, producing 1.67 mol of LA per mol of glucose [88]. On the other hand, heterofermentative LAB can ferment hexoses and pentoses exclusively via the PK pathway, producing LA, acetic acid or ethanol, and CO2. Thus, the theoretical yield obtained is 1 mol of LA per mol of glucose or pentose [88]. By contrast, facultative heterofermentative LAB can metabolize hexoses via the EMP pathway and pentoses via the PK pathway, obtaining 2 mol of LA per mol of glucose and 1 mol of LA per mol of pentose [88].
3.4.2. Production of LA from SBP Hydrolysates
Different studies have been performed to produce LA from SBP (Table 3). To increase the LA yield, several authors have varied the pH regulation mode, nutrient supplementation and the type of processing, such as separate hydrolysis and fermentation, simultaneous saccharification and fermentation, fed-batch fermentation or continuous fermentation. For instance, Marzo et al. studied the effect of supplementing the SBP hydrolysate with different nitrogen sources, finding that it is necessary to supplement it with yeast extract to increase the production of LA [94]. Additionally, they also studied pH regulation during the lactic fermentation of SBP hydrolysate with Lactobacillus plantarum, reaching 30 g/L of LA with a yield of 0.12 gLA/gSBP by adding 27 g/L of CaCO3 [94]. In another report, the same authors evaluated the pretreatment of SBP, testing acid, alkaline and biological pretreatment. They increased the production of LA to 50 g/L with a yield of 0.5 gLA/gSBP when the SBP was pretreated with 1% H2SO4 [52]. Díaz et al. studied different simultaneous saccharification and fermentation strategies to produce LA from SBP with Lactobacillus casei [95]. They achieved the maximum concentration of 27 g/L of LA with a yield of 0.13 gLA/gSBP using a fed-batch SSF process with pH control (by adding 30 g/L CaCO3) and nutrient supplementation (by adding MRS medium 0.2 mL/mL).
Due to the composition of SBP, the hydrolysis of SBP produces a medium rich in glucose, but other sugars such as fructose, mannose, arabinose galactose, raffinose, rhamnose, xylose and galacturonic acid are also included [24]. It is difficult for a single microbial species to completely assimilate such a medium. Lactic acid production from arabinose, galactose and xylose derived from SBP is not as efficient as from glucose [98]. For example, Bacillus coagulans was used to produce lactic acid from sugar beet pulp hydrolysates [97]. This strain was able to consume glucose and xylose; however, arabinose was not totally consumed at the end of fermentation. Most homofermentative LAB, such as Lactobacillus delbrueckii and Lactobacillus acidophilus, can produce lactic acid from glucose but not from sugars derived from hemicellulose, such as arabinose and xylose [99]. For better utilization of the substrate, it is necessary to use LAB able to utilize pentoses. However, pentoses are only utilized by some lactobacilli. This is the case of the facultative heterofermentative microorganism Lactobacillus casei 2246, which degrades hexoses, mainly glucose, through the EMP pathway, and pentoses by the PK pathway [95]. This strain has been demonstrated to produce lactic acid from glucose and arabinose from simultaneous saccharification and fermentation of SBP. Moreover, lactic acid fermentation can be improved by using a mixed population of LAB with different assimilation profiles [100]. In fact, the effectiveness of LA production can be improved by 10–30% by using mixed cultures. Hence, Berlowska et al. studied the effect of mixed cultures of LAB species through simultaneous saccharification and lactic fermentation [24]. They performed the fermentation in two steps: the first one with a monoculture able to ferment mainly glucose and the second one with another strain able to consume unfermented sugars (arabinose and xylose). Using this procedure, most sugars were consumed by the mixed culture, reaching a LA concentration of 60 g/L with a yield of 0.55 gLA/gSBP with the strain Lactobacillus plantarum HII in the first step and Lactobacillus plantarum HII and Lactobacillus brevis PCM 488 in the second. The same strategy was followed by Alexandri et al. after observing the non-complete consumption of the hydrolyzed sugars from SBP [96]. They produced 22 g/L of LA with a yield of 0.78 gLA/gSBP with the strains L. coryniformis subsp. torquens DSM 20005 and isolate A250 (most likely L. preudomesenteroides), adding the second strain when half of the glucose was consumed [96]. Additionally, a similar procedure was performed by Diaz et al., where SBP hydrolysate was fermented first to ethanol and then to LA with the strain Lactobacillus plantarum [73]. In that study, the complete use of sugars was achieved by producing ethanol and LA sequentially.
An interesting biorefinery process was presented by Oliveira et al. [97]. This process can be implemented inside the processing of sugar beet to produce sugar. They produce LA from SBP via continuous fermentation with Bacillus coagulans, reaching 2781.01 g of LA from 3916.91 g of sugars with a maximum productivity of 18.06 g/L/h.
3.5. Polyhydroxyalkanoates Fermentation
The first identification of poly-3-hydroxybutyrate (P(3HB)) was performed in the strain Bacillus megaterium by Lemoigne in 1926 [101]. Afterward, more than 300 bacterial strains have been identified as PHA producers. Some examples include Cupriavidus necator (also named Ralstonia eutropha), Pseudomonas aeruginosa, Pseudomonas oleovarans and Pseudomonas stutzeri [102]. These bacteria are able to accumulate PHA inside the cell cytoplasm as a reserve of carbon and energy. Therefore, they are produced when the microorganisms cannot grow normally due to a deficiency of nutrients and an excess of carbon.
3.5.1. Metabolic Pathway to Produce PHAs via Fermentation
The production of PHAs is induced by the limitation of nutrients in the medium used for microorganism growth. This limitation activates the pathways of metabolism that bacteria use to produce PHAs [11]. The metabolic pathways involved in the production of PHA depend on the carbon source and the microorganism used. These bacteria can use different carbon sources to produce PHAs, such as carbohydrates or volatile fatty acids (VFAs) [103].
In pure culture fermentation, carbohydrates are metabolized to pyruvate via the Enter–Doudoroff pathway. Afterward, pyruvate is converted to acetyl-CoA and, under growth-limiting conditions, acetyl-CoA is transformed into P(3HB) by the action of three enzymes: 3-ketothiolase (PhaA), acetoacetyl-CoA reductase (PhaB) and PHA synthase (PhaC) [103]. Through this pathway, the obtained yield will depend on the carbon source. Thus, glucose produces the highest yield (0.40 g PHA/g); however, other sugars such as xylose or arabinose can also be used to produce PHAs, although at lower yields (0.17–0.19 g PHA/g) [104].
The production of PHAs from VFAs follows the same route for metabolism once they are converted to the corresponding acyl-CoA, being the precursors for different hydroxyalkanoate monomers. In this way, P(3HB) is produced from acetate, and 3HV, 3-hydroxy-2-methylvalerate (3H2MV) or 3-hydroxy-2-methylbutyrate (3H2MB) are produced from propionate [11].
PHAs can be produced from pure cultures following a two-step process: growth phase and accumulation phase [11]. Firstly, the strain is cultivated in a medium with a proper ratio of carbon, nitrogen and nutrients. Secondly, one of the essential nutrients (nitrogen, phosphorus or oxygen) is restricted to induce the accumulation of PHA inside the cell. PHAs can also be produced by mixed cultures through the fermentation of VFAs and the process requires two stages [11]. First of all, microorganisms with high PHA storage capacity are selected by imposing cycles where an essential nutrient is restricted. Afterward, the selected microorganisms are cultured to produce PHAs by restricting the same essential nutrient restricted in the previous step. The advantage of using mixed culture is the reduction in production cost due to sterilization is not required and the culture can adapt to various complex feedstocks [105,106].
3.5.2. Production of PHAs from SBP
As previously mentioned, SBP hydrolysate is a complete medium with a great variety of sugars, including glucose, rhamnose, arabinose, galactose, xylose and galacturonic acid. However, there are no published papers on the production of PHA from SBP-derived sugars different from glucose.
Kurt-Kızıldoğan et al. produced poly(3-hydroxybutyrate) (PHB), one of the main PHAs, with Haloarcula sp. TG1 from glucose derived from different agricultural wastes [107]. Among them, the highest PHA content (45.6% of the biomass) was achieved using SBP treated with rCKT3eng, a recombinant endoglucanase of Haloarcula sp. CKT3 expressed in E. coli BL21 (DE3) cells (pH 7.35, 72 h, 37 °C).
The most common pathway in bacteria, yeast and fungi to convert glucose to PHAs is the EMP [108,109]. However, the model organism for PHA production, C. necator, lacks the gene for the key enzyme of this pathway, utilizing the Entner–Doudoroff (ED) pathway instead [110]. There are only a few strains able to convert C5 sugars and produce PHAs, but when they do, the conversion efficiencies are very low [111]. It has been demonstrated that some microorganisms are able to perform this conversion from hemicellulose hydrolysates derived from rice straw, sugarcane bagasse, sugar maple wood chips, etc., such as Bacillus firmus, Cupriavidus necator, Burkholderia cepacia, etc. [109]. However, no papers have been found describing PHA production from C5 sugars derived from SBP. Numerous metabolic engineering strategies have been explored for metabolizing pentose sugars available in lignocellulosic hydrolysates. For example, a strain of C. necator has been modified to metabolize arabinose through heterologous expression of a set of E. coli genes for L-arabinose uptake and metabolism [112].
As stated above, VFAs are another carbon source to produce PHAs. SBP has also been studied as raw material to produce VFAs, with acetic, lactic, caproic and butyric being the main acids produced [113]. These acids are commonly produced through acidogenic fermentation by mixed microbial cultures. This fermentation involves two steps of the anaerobic digestion process, hydrolysis and acidogenesis, and the inhibition of methanogenesis [114]. In this process, the organic matter is hydrolyzed into sugars, amino acids and fatty acids. Afterward, these compounds are converted into VFAs by acidogenic bacteria.
4. Conclusions and Future Directions
Bioplastic production from renewable sources is a topic that has gained interest in recent years. In this direction, SBP is a versatile by-product from the food industry that can be used as raw material to produce value-added products, such as LA and PHAs, through biotechnological processes. Although several studies have been performed on pretreatments and enzymatic hydrolysis of SBP, only a few focused on the production of LA or PHAs, which can be used as precursors of bioplastics. Only one study was found where PHAs are obtained from SBP through a sequential process of hydrolysis and fermentation.
Focusing on another alternative process to produce PHAs, that is from VFAs, there is also a lack of studies where VFAs produced from SBP are used to obtain PHAs. However, there are several studies based on the production of hydrogen and VFAs through the anaerobic digestion of SBP. Hence, it seems that it is a feasible process that has not yet been studied in depth.
Additionally, SBP is composed of similar percentages of cellulose, hemicellulose and pectin. This characteristic makes it an interesting raw material to use in the framework of a biorefinery. Only a few authors have proposed a biorefinery process applied to this material, where pectin, phenolic compounds and sugar-rich hydrolysates can be fermented to ethanol, LA or succinic acid, among others, facilitating the preparation of valuable products. Further research should be carried out in this direction to implement a cost-effective process in the sugar industry.
Conceptualization, C.M.-G., A.B. and A.B.D.; methodology, C.M.-G.; investigation, C.M.-G.; writing—original draft preparation, C.M.-G.; writing—review and editing, A.B. and A.B.D.; visualization, C.M.-G.; project administration, A.B.; funding acquisition, A.B. All authors have read and agreed to the published version of the manuscript.
Not applicable.
Not applicable.
Not applicable.
The authors thank “Ministerio de Economía, Industria y Competitividad”, “Agencia Estatal de Investigación (AEI) and “Fondo Europeo de Desarrollo Regional (FEDER)” for the financial support of this study. C.M.-G thanks “Ministerio de Universidades del Gobierno de España” for the allocated Budget from the NextGenerationEU program to public universities for the requalification of the Spanish university system, which funds her postdoctoral position at the University of Cádiz in the form of a Margarita Salas fellowship (ref. 2021-067/PN/MS-RECUAL/CD).
The authors declare no conflict of interest.
| CBU | Cellobiase activity units |
| PGU | Polygalacturonase activity units |
| COD | Chemical oxygen demand |
| d.m. | Dry matter |
| FPU | Filter paper unit |
| HU | Hemicellulase activity units |
| LA | Lactic acid |
| LAB | Lactic acid bacteria |
| LCB | Lignocellulosic biomass |
| MRS | Man, Rogosa and Sharpe broth |
| PA | Polyamide |
| PBAT | Polybutylene adipate terephthalate |
| PBS | Polybutylene succinate |
| PCL | Polycaprolactone |
| PE | Polyethene |
| PET | Polyethene terephthalate |
| PGU | Polygalacturonase activity units |
| PHA | Polyhydroxyalkanoate |
| PLA | Poly-lactic acid |
| POS | Pectin-derived oligosaccharides |
| PP | Polypropylene |
| PTT | Polytrimethylene terephthalate |
| RS | Reducing sugars |
| SBP | Sugar beet pulp |
| SLR | Solid-liquid ratio |
| SSF | Solid-state fermentation |
| TS | Total solids |
| U | Unit of enzyme |
| VAP | Value-added product |
| VFAs | Volatile fatty acids |
| VS | Volatile solid |
| YH | Hydrolysis yield |
Footnotes
Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to people or property resulting from any ideas, methods, instructions or products referred to in the content.
![View Image - Figure 1. Classification and examples of each type of plastic. PA: polyamide, PTT: polytrimethylene terephthalate; PE: polyethylene; PET: polyethylene terephthalate; PP: polypropylene; PLA: poly-lactic acid; PHA: polyhydroxyalkanoates; PBS: polybutylene succinate; PBAT: polybutylene adipate terephthalate; PCL: polycaprolactone. Adapted from [4].](https://media.proquest.com/media/hms/THUM/2/vAtXT?_a=ChgyMDI2MDQyOTE1MjM1ODUzNTo5NzM4NDQSBzEzODMzMjMaCk9ORV9TRUFSQ0giDTIxNi43My4yMTcuMjMqBzIwNTU0MTQyCjI4NDMwNTA4NDk6C0lubGluZUltYWdlQgEwUgZPbmxpbmVaA0lMSWIEVEhVTWoKMjAyMy8wMS8wMXIKMjAyMy8xMi8zMXoAggEgUC0xMDAwMDg0LTIwMTM5NS1TVEFGRi1udWxsLW51bGySAQZPbmxpbmXKAWdNb3ppbGxhLzUuMCBBcHBsZVdlYktpdC81MzcuMzYgKEtIVE1MLCBsaWtlIEdlY2tvOyBjb21wYXRpYmxlOyBDbGF1ZGVCb3QvMS4wOyArY2xhdWRlYm90QGFudGhyb3BpYy5jb20p0gESU2Nob2xhcmx5IEpvdXJuYWxzmgIHUHJlUGFpZKoCG09TOkVNUy1GdWxsVGV4dC1nZXRGdWxsVGV4dMoCD0FydGljbGV8RmVhdHVyZeICAU7yAgD6AgFZggMDV2ViigMcQ0lEOjIwMjYwNDI5MTUyMzU4NTM1OjQxMTY2OQ%3D%3D&_s=ie41299dylyKcFd0BwbT4bFY1fM%3D "View Image - Figure 1. Classification and examples of each type of plastic. PA: polyamide, PTT: polytrimethylene terephthalate; PE: polyethylene; PET: polyethylene terephthalate; PP: polypropylene; PLA: poly-lactic acid; PHA: polyhydroxyalkanoates; PBS: polybutylene succinate; PBAT: polybutylene adipate terephthalate; PCL: polycaprolactone. Adapted from [4].")
Enlarge this image.Figure 1. Classification and examples of each type of plastic. PA: polyamide, PTT: polytrimethylene terephthalate; PE: polyethylene; PET: polyethylene terephthalate; PP: polypropylene; PLA: poly-lactic acid; PHA: polyhydroxyalkanoates; PBS: polybutylene succinate; PBAT: polybutylene adipate terephthalate; PCL: polycaprolactone. Adapted from [4].
![View Image - Figure 2. Structure of lignocellulosic biomass. Adapted from [21].](https://media.proquest.com/media/hms/THUM/4/vAtXT?_a=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%3D%3D&_s=znMPiZPIgT8e8qIhWTdxumolCU4%3D "View Image - Figure 2. Structure of lignocellulosic biomass. Adapted from [21].")
Enlarge this image.Figure 2. Structure of lignocellulosic biomass. Adapted from [21].
Enlarge this image.Figure 3. Flowchart showing the main steps in the production of bioplastics from sugar beet pulp, for which the associated issues are addressed in this review.
Enlarge this image.Figure 4. (A) Products obtained from 1 ton of sugar beet and (B) chemical composition of sugar beet pulp.
![View Image - Figure 5. Flowchart of sugar beet processing. Adapted from [22].](https://media.proquest.com/media/hms/THUM/10/vAtXT?_a=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%3D%3D&_s=Ocenfm3RXQ5w1hyUjmRSiXxsLxc%3D "View Image - Figure 5. Flowchart of sugar beet processing. Adapted from [22].")
Enlarge this image.Figure 5. Flowchart of sugar beet processing. Adapted from [22].
Pretreatments applied to SBP. YH: hydrolysis yield (gRS/gSBP).
| Pretreatment Type | Conditions | YH | Reference | |
|---|---|---|---|---|
| Physical | Milling | 0.8–1.0 mm | 0.71 g/g | [ |
| Milling + Ultrasound | 0.8–1.0 mm |
0.70–0.76 g/g | [ |
|
| Chemical | Dilute acid | Autoclave, 150 °C, 10 min, 1.1% w/w H2SO4 | 0.82 g/g | [ |
| Dilute acid | 120 °C, 6 min, 0.1 N HCl | 0.86 g/g | [ |
|
| Dilute acid | 120 °C, 0.66% H2SO4 | 0.63 g/g | [ |
|
| Dilute acid | 1% H2SO4 | 0.49 g/g | [ |
|
| Physicochemical | Milling + Thermal | Autoclave, 121 °C, 30 or 60 min, 2% w/w H2SO4 | 0.85 g/g | [ |
| Milling + Thermal | Autoclave, 120 °C, 30 or 60 min, water | 0.75 g/g | [ |
|
| Thermal | Autoclave, 121 °C, 20 min | 0.60 g/g | [ |
|
| Biological | Ensiling | Lactobacillus species | 0.95 g/g | [ |
| Solid-state |
Aspergillus awamori, |
0.34 g/g | [ |
|
Lactic acid production from SBP. YLA: lactic acid yield (gLA/gSBP).
| Reference | Strain | Conditions | Concentration | YLA |
|---|---|---|---|---|
| [ |
Lactobacillus plantarum HII & |
SSF with co-culture | 60 g/L | 0.55 g/g |
| [ |
L. coryniformis subsp. torquens DSM 20005 & L. preudomesenteroides | SHF with co-culture | 22 g/L | 0.78 g/g |
| [ |
Lactobacillus plantarum | SHF | 30 g/L | 0.12 g/g |
| [ |
Lactobacillus plantarum | SHF with pretreated SBP | 50 g/L | 0.5 g/g |
| [ |
Lactobacillus casei | Fed-fach SSF | 27 g/L | 0.13 g/g |
| [ |
Bacillus coagulans | Continuous fermentation | 35 g/L | 0.71 g/g |
References
1. Narancic, T.; O’Connor, K.E. Plastic Waste as a Global Challenge: Are Biodegradable Plastics the Answer to the Plastic Waste Problem?. Microbiology; 2019; 165, pp. 129-137. [DOI: https://dx.doi.org/10.1099/mic.0.000749]
2. Plasctics Europe Plastics-the Facts 2021 An Analysis of European Plastics Production, Demand and Waste Data. Available online: https://plasticseurope.org/knowledge-hub/plastics-the-facts-2021/ (accessed on 24 March 2022).
3. Rivero, C.P.; Hu, Y.; Kwan, T.H.; Webb, C.; Theodoropoulos, C.; Daoud, W.; Lin, C.S.K. Bioplastics From Solid Waste. Current Developments in Biotechnology and Bioengineering: Solid Waste Management; Elsevier: Amsterdam, The Netherlands, 2016; pp. 1-26. ISBN 9780444636751
4. European Bioplastic European Bioplastic. Available online: http://www.european-bioplastics.org (accessed on 3 February 2023).
5. Martin, O.; Avérous, L. Poly(Lactic Acid): Plasticization and Properties of Biodegradable Multiphase Systems. Polymer; 2001; 42, pp. 6209-6219. [DOI: https://dx.doi.org/10.1016/S0032-3861(01)00086-6]
6. Bonartsev, A.P.; Bonartseva, G.A.; Reshetov, I.V.; Kirpichnikov, M.P.; Shaitan, K.V. Application of Polyhydroxyalkanoates in Medicine and the Biological Activity of Natural Poly(3-Hydroxybutyrate). Acta Nat.; 2019; 11, pp. 4-16. [DOI: https://dx.doi.org/10.32607/20758251-2019-11-2-4-16]
7. Lasprilla, A.J.R.; Martinez, G.A.R.; Lunelli, B.H.; Jardini, A.L.; Filho, R.M. Poly-Lactic Acid Synthesis for Application in Biomedical Devices—A Review. Biotechnol. Adv.; 2012; 30, pp. 321-328. [DOI: https://dx.doi.org/10.1016/j.biotechadv.2011.06.019]
8. Saniei, H.; Mousavi, S. Surface Modification of PLA 3D-Printed Implants by Electrospinning with Enhanced Bioactivity and Cell Affinity. Polymer; 2020; 196, 122467. [DOI: https://dx.doi.org/10.1016/j.polymer.2020.122467]
9. Samrot, A.V.; Sean, T.C.; Kudaiyappan, T.; Bisyarah, U.; Mirarmandi, A.; Faradjeva, E.; Abubakar, A.; Ali, H.; Lavanya, J.; Angalene, A. et al. Production, Characterization and Application of Nanocarriers Made of Polysaccharides, Proteins, Bio-Polyesters and Other Biopolymers: A Review. Int. J. Biol. Macromol.; 2020; 165, pp. 3088-3105. [DOI: https://dx.doi.org/10.1016/j.ijbiomac.2020.10.104]
10. Sharma, V.; Sehgal, R.; Gupta, R. Polyhydroxyalkanoate ( PHA ): Properties and Modifications. Polymer; 2020; 212, 123161. [DOI: https://dx.doi.org/10.1016/j.polymer.2020.123161]
11. Reis, M.; Albuquerque, M.; Villano, M.; Majone, M. Mixed Culture Processes for Polyhydroxyalkanoate Production from Agro-Industrial Surplus/Wastes as Feedstocks. Comprehensive Biotechnology; 2nd ed. Elsevier: Amsterdam, The Netherlands, 2011; Volume 6, pp. 669-683. ISBN 9780080885049
12. Sen, K.Y.; Baidurah, S. Renewable Biomass Feedstocks for Production of Sustainable Biodegradable Polymer. Curr. Opin. Green Sustain. Chem.; 2021; 27, 100412. [DOI: https://dx.doi.org/10.1016/j.cogsc.2020.100412]
13. Tarrahi, R.; Fathi, Z.; Seydibeyoğlu, M.Ö.; Doustkhah, E.; Khataee, A. Polyhydroxyalkanoates (PHA): From Production to Nanoarchitecture. Int. J. Biol. Macromol.; 2020; 146, pp. 596-619. [DOI: https://dx.doi.org/10.1016/j.ijbiomac.2019.12.181] [PubMed: https://www.ncbi.nlm.nih.gov/pubmed/31899240]
14. Abdel-Rahman, M.A.; Tashiro, Y.; Sonomoto, K. Recent Advances in Lactic Acid Production by Microbial Fermentation Processes. Biotechnol. Adv.; 2013; 31, pp. 877-902. [DOI: https://dx.doi.org/10.1016/j.biotechadv.2013.04.002] [PubMed: https://www.ncbi.nlm.nih.gov/pubmed/23624242]
15. Wellenreuther, C.; Wolf, A.; Zander, N. Cost Competitiveness of Sustainable Bioplastic Feedstocks – A Monte Carlo Analysis for Polylactic Acid. Clean. Eng. Technol.; 2022; 6, 100411. [DOI: https://dx.doi.org/10.1016/j.clet.2022.100411]
16. Yousuf, A.; Pirozzi, D.; Sannino, F. Fundamentals of Lignocellulosic Biomass. Lignocellulosic Biomass to Liquid Biofuels; Elsevier: Amsterdam, The Netherlands, 2019; pp. 1-15. ISBN 9780128159361
17. Sani, R.K. Biorefining of Biomass to Biofuels: Opportunities and Perception; Springer: Berlin/Heidelberg, Germany, 2018; Volume 4, ISBN 978-3-319-67678-4
18. Obruca, S.; Benesova, P.; Marsalek, L.; Marova, I. Use of Lignocellulosic Materials for PHA Production. Chem. Biochem. Eng. Q.; 2015; 29, pp. 135-144. [DOI: https://dx.doi.org/10.15255/CABEQ.2014.2253]
19. Al-Battashi, H.S.; Annamalai, N.; Sivakumar, N.; Al-Bahry, S.; Tripathi, B.N.; Nguyen, Q.D.; Gupta, V.K. Lignocellulosic Biomass (LCB): A Potential Alternative Biorefinery Feedstock for Polyhydroxyalkanoates Production. Rev. Environ. Sci. Biotechnol.; 2019; 18, pp. 183-205. [DOI: https://dx.doi.org/10.1007/s11157-018-09488-4]
20. Isikgor, F.H.; Becer, C.R. Lignocellulosic Biomass: A Sustainable Platform for the Production of Bio-Based Chemicals and Polymers. Polym. Chem.; 2015; 6, pp. 4497-4559. [DOI: https://dx.doi.org/10.1039/C5PY00263J]
21. Streffer, F. Lignocellulose to Biogas and Other Products. JSM Biotechnol. Biomed. Eng.; 2014; 2, 1023.
22. Marzo, C.; Díaz, A.B.; Caro, I.; Blandino, A. Status and Perspectives in Bioethanol Production From Sugar Beet. Bioethanol Production from Food Crops; Elsevier: Amsterdam, The Netherlands, 2019; pp. 61-79.
23. OECDFAO. OECD-FAO Agricultural Outlook 2022-2031; OECD: Paris, France, 2022.
24. Berlowska, J.; Pielech-przybylska, K.; Balcerek, M.; Dziekonska-kubczak, U.; Patelski, P.; Dziugan, P.; Kregiel, D. Simultaneous Saccharification and Fermentation of Sugar Beet Pulp for Efficient Bioethanol Production. Biomed Res. Int.; 2016; 2016, 10. [DOI: https://dx.doi.org/10.1155/2016/3154929] [PubMed: https://www.ncbi.nlm.nih.gov/pubmed/27722169]
25. Panella, L. Sugar Beet as an Energy Crop. Sugar Tech.; 2010; 12, pp. 288-293. [DOI: https://dx.doi.org/10.1007/s12355-010-0041-5]
26. Schonhoff, A.; Ihling, N.; Schreiber, A.; Zapp, P. Environmental Impacts of Biosurfactant Production Based on Substrates from the Sugar Industry. Sustain. Chem. Eng.; 2022; 10, pp. 9345-9358. [DOI: https://dx.doi.org/10.1021/acssuschemeng.2c01256]
27. Pezzi, G. Considerations of the Technological Quality Assessment of Sugarbeet. Sugar Ind.; 2011; 136, pp. 85-89. [DOI: https://dx.doi.org/10.36961/si11041]
28. Cubero, M.T.G.; Sanz, M.C.; Benito, G.G.; Puerta, M.G.D. Distribution of Colorants in the Evaporation and First Crystallization Stages. Sugar Ind.; 2004; 129, pp. 660-666.
29. Vaccari, G.; Wawro, P.; Tamburini, E.; Sgualdino, G.; Bernardi, T. Cooling Crystallization of Raw Juice: Laboratory Investigations of Sucrose Crystal Growth Kinetics. Sugar Ind.; 1996; 121, pp. 111-117.
30. Vaccari, G.; Wawro, P.; Tamburini, E.; Sgualdino, G.; Bernardi, T. Cooling Crystallization of Microfiltered Raw Juice and of Traditional Thick Juice: A Comparison. Sugar Ind.; 2002; 127, pp. 22-28.
31. Merkes, R.; Kröhl, M.; Mugele, H.; Sauer, M. Sugarbeet Production Technology in the Year 2000: Cost Reduction, Environmental Protection, Sustainability. Sugar Ind.; 2001; 126, pp. 804-811.
32. Baryga, A.; Połeć, B.; Klasa, A.; Olejnik, T.P. Application of Sugar Beet Pulp Digestate as a Soil Amendment in the Production of Energy Maize. Processes; 2021; 9, 765. [DOI: https://dx.doi.org/10.3390/pr9050765]
33. Baryga, A.; Połeć, B.; Klasa, A. Quality of Sugar Beets under the Effects of Digestate Application to the Soil. Processes; 2020; 8, 1402. [DOI: https://dx.doi.org/10.3390/pr8111402]
34. Baryga, A.; Polec, B.; Skibniewska, K.A.; Seciu, E.; Grabara, J. Utilisation of Residual Waste From Sugar Beet Pulp Fermentation As Fertiliser in Sustainable Agriculture. J. Environ. Prot. Ecol.; 2016; 17, pp. 1048-1057.
35. Rana, A.K.; Kumar Gupta, V.; Newbold, J.; Roberts, D.; Rees, R.M.; Krishnamurthy, S.; Kumar Thakur, V. Sugar Beet Pulp: Resurgence and Trailblazing Journey towards a Circular Bioeconomy. Fuel; 2022; 312, 122953. [DOI: https://dx.doi.org/10.1016/j.fuel.2021.122953]
36. Dinand, E.; Chanzy, H.; Vignon, M.R. Parenchymal Cell Cellulose from Sugar Beet Pulp: Preparation and Properties. Cellulose; 1996; 3, pp. 183-188. [DOI: https://dx.doi.org/10.1007/BF02228800]
37. Dinand, E.; Chanzy, H.; Vignon, R.M. Suspensions of Cellulose Microfibrils from Sugar Beet Pulp. Food Hydrocoll.; 1999; 13, pp. 275-283. [DOI: https://dx.doi.org/10.1016/S0268-005X(98)00084-8]
38. Michel, F.; Thibault, J.-F.; Barry, J.-L.; de Baynast, R. Preparation and Characterisation of Dietary Fibre from Sugar Beet Pulp. J. Sci. Food Agric.; 1988; 42, pp. 77-85. [DOI: https://dx.doi.org/10.1002/jsfa.2740420109]
39. Grahovac, J.; Rončević, Z. Environmental Impacts of the Confectionary Industry. Environmental Impact of Agro-Food Industry and Food Consumption; Elsevier: Amsterdam, The Netherlands, 2021; pp. 189-216. ISBN 9780128213636
40. Ward, D.P.; Cárdenas-Fernández, M.; Hewitson, P.; Ignatova, S.; Lye, G.J. Centrifugal Partition Chromatography in a Biorefinery Context: Separation of Monosaccharides from Hydrolysed Sugar Beet Pulp. J. Chromatogr. A; 2015; 1411, pp. 84-91. [DOI: https://dx.doi.org/10.1016/j.chroma.2015.08.006] [PubMed: https://www.ncbi.nlm.nih.gov/pubmed/26278358]
41. Bolaji, I.; Nejad, B.; Billham, M.; Mehta, N.; Smyth, B.; Cunningham, E. Multi-Criteria Decision Analysis of Agri-Food Waste as a Feedstock for Biopolymer Production. Resour. Conserv. Recycl.; 2021; 172, 105671. [DOI: https://dx.doi.org/10.1016/j.resconrec.2021.105671]
42. Abo, B.O.; Gao, M.; Wang, Y.; Wu, C.; Ma, H.; Wang, Q. Lignocellulosic Biomass for Bioethanol: An Overview on Pretreatment, Hydrolysis and Fermentation Processes. Rev. Environ. Health; 2019; 34, pp. 57-68. [DOI: https://dx.doi.org/10.1515/reveh-2018-0054]
43. Solarte-Toro, J.C.; Romero-García, J.M.; Martínez-Patiño, J.C.; Ruiz-Ramos, E.; Castro-Galiano, E.; Cardona-Alzate, C.A. Acid Pretreatment of Lignocellulosic Biomass for Energy Vectors Production: A Review Focused on Operational Conditions and Techno-Economic Assessment for Bioethanol Production. Renew. Sustain. Energy Rev.; 2019; 107, pp. 587-601. [DOI: https://dx.doi.org/10.1016/j.rser.2019.02.024]
44. Haldar, D.; Purkait, M.K. A Review on the Environment-Friendly Emerging Techniques for Pretreatment of Lignocellulosic Biomass: Mechanistic Insight and Advancements. Chemosphere; 2021; 264, 128523. [DOI: https://dx.doi.org/10.1016/j.chemosphere.2020.128523]
45. Alvira, P.; Tomás-Pejó, E.; Ballesteros, M.; Negro, M.J. Pretreatment Technologies for an Efficient Bioethanol Production Process Based on Enzymatic Hydrolysis: A Review. Bioresour. Technol.; 2010; 101, pp. 4851-4861. [DOI: https://dx.doi.org/10.1016/j.biortech.2009.11.093]
46. Xu, J.K.; Sun, R.C. Recent Advances in Alkaline Pretreatment of Lignocellulosic Biomass. Biomass Fractionation Technologies for a Lignocellulosic Feedstock Based Biorefinery; Elsevier: Amsterdam, The Netherlands, 2016; pp. 431-459. ISBN 9780128025611
47. Rahmati, S.; Doherty, W.; Dubal, D.; Atanda, L.; Moghaddam, L.; Sonar, P.; Hessel, V.; Ostrikov, K.K. Pretreatment and Fermentation of Lignocellulosic Biomass: Reaction Mechanisms and Process Engineering. React. Chem. Eng.; 2020; 5, pp. 2017-2047. [DOI: https://dx.doi.org/10.1039/D0RE00241K]
48. Rezicó, T.; Oros, D.; Markovicó, I.; Kracher, D.; Ludwig, R.; Šantek, B.; Rezic, T.; Oros, D.; Markovicó, I.; Kracher, D. et al. Integrated Hydrolyzation and Fermentation of Sugar Beet Pulp to Bioethanol. J. Microbiol. Biotechnol.; 2013; 23, pp. 1244-1252. [DOI: https://dx.doi.org/10.4014/jmb.1210.10013] [PubMed: https://www.ncbi.nlm.nih.gov/pubmed/23851274]
49. Donkoh, E.; Degenstein, J.; Tucker, M.; Ji, Y. Optimization of Enzymatic Hydrolysis of Dilute Acid Pretreated Sugar Beet Pulp Using Response Surface Design. J. Sugarbeet Res.; 2012; 49, pp. 26-38. [DOI: https://dx.doi.org/10.5274/jsbr.49.1.26]
50. El-gendy, N.S.; Madian, H.R.; Nassar, H.N. Response Surface Optimization of the Thermal Acid Pretreatment of Sugar Beet Pulp for Bioethanol Production Using Trichoderma Viride and Saccharomyces Cerevisiae. Recent Pat. Biotechnol.; 2015; 9, pp. 50-62. [DOI: https://dx.doi.org/10.2174/1872208309666150916092450]
51. Zheng, Y.; Lee, C.; Yu, C.; Cheng, Y.S.; Zhang, R.; Jenkins, B.M.; VanderGheynst, J.S. Dilute Acid Pretreatment and Fermentation of Sugar Beet Pulp to Ethanol. Appl. Energy; 2013; 105, pp. 1-7. [DOI: https://dx.doi.org/10.1016/j.apenergy.2012.11.070]
52. Marzo, C.; Díaz, A.B.; Caro, I.; Blandino, A. Effect of Several Pretreatments on the Lactic Acid Production from Exhausted Sugar Beet Pulp. Foods; 2021; 10, 2414. [DOI: https://dx.doi.org/10.3390/foods10102414] [PubMed: https://www.ncbi.nlm.nih.gov/pubmed/34681463]
53. Zheng, Y.; Yu, C.; Cheng, Y.S.; Zhang, R.; Jenkins, B.; VanderGheynst, J.S. Effects of Ensilage on Storage and Enzymatic Degradability of Sugar Beet Pulp. Bioresour. Technol.; 2011; 102, pp. 1489-1495. [DOI: https://dx.doi.org/10.1016/j.biortech.2010.09.105] [PubMed: https://www.ncbi.nlm.nih.gov/pubmed/21036038]
54. Cárdenas-Fernández, M.; Bawn, M.; Hamley-Bennett, C.; Bharat, P.K.V.; Subrizi, F.; Suhaili, N.; Ward, D.P.; Bourdin, S.; Dalby, P.A.; Hailes, H.C. et al. An Integrated Biorefinery Concept for Conversion of Sugar Beet Pulp into Value-Added Chemicals and Pharmaceutical Intermediates. Faraday Discuss.; 2017; 202, pp. 415-431. [DOI: https://dx.doi.org/10.1039/C7FD00094D]
55. Valdés, G.; Mendonça, R.T.; Aggelis, G. Lignocellulosic Biomass as a Substrate for Oleaginous Microorganisms: A Review. Appl. Sci.; 2020; 10, 7698. [DOI: https://dx.doi.org/10.3390/app10217698]
56. Canilha, L.; Chandel, A.K.; dos Santos Milessi, T.S.; Fernandes Antunes, F.A.; Luiz Da Costa Freitas, W.; Almeida Felipe, M.D.G.; Silva, S.S. Bioconversion of Sugarcane Biomass into Ethanol: An Overview about Composition, Pretreatment Methods, Detoxification of Hydrolysates, Enzymatic Saccharification, and Ethanol Fermentation. J. Biomed. Biotechnol.; 2012; 2012, 15. [DOI: https://dx.doi.org/10.1155/2012/989572]
57. Ivetic, D.Z.; Marina, B.S.; Antov, M.G.; Ivetić, D.Ž.; Šćiban, M.B.; Antov, M.G. Enzymatic Hydrolysis of Pretreated Sugar Beet Shreds: Statistical Modeling of the Experimental Results. Biomass Bioenergy; 2012; 7, pp. 387-394. [DOI: https://dx.doi.org/10.1016/j.biombioe.2012.09.020]
58. Foster, B.L.; Dale, B.E.; Doran-Peterson, J.B. Enzymatic Hydrolysis of Ammonia-Treated Sugar Beet Pulp. Appl. Biochem. Biotechnol.; 2001; 91, pp. 91-93. [DOI: https://dx.doi.org/10.1385/ABAB:91-93:1-9:269]
59. Ivetic, D.T.; Antov, M.G. The Impact of Pretreatments on Cellulose from Sugar Beet Shreds and Its Susceptibility to Enzymatic Hydrolysis. Cellul. Chem. Technol.; 2016; 50, pp. 139-146.
60. Li, G.; Sun, Y.; Guo, W.; Yuan, L. Comparison of Various Pretreatment Strategies and Their Effect on Chemistry and Structure of Sugar Beet Pulp. J. Clean. Prod.; 2018; 181, pp. 217-223. [DOI: https://dx.doi.org/10.1016/j.jclepro.2018.01.259]
61. Maitan-Alfenas, G.P.; Visser, E.M.; Guimarães, V.M. Enzymatic Hydrolysis of Lignocellulosic Biomass: Converting Food Waste in Valuable Products. Curr. Opin. Food Sci.; 2015; 1, pp. 44-49. [DOI: https://dx.doi.org/10.1016/j.cofs.2014.10.001]
62. Anand, G.; Yadav, S.; Yadav, D. Production, Purification and Biochemical Characterization of an Exo-Polygalacturonase from Aspergillus Niger MTCC 478 Suitable for Clarification of Orange Juice. 3 Biotech; 2017; 7, 122. [DOI: https://dx.doi.org/10.1007/s13205-017-0760-3]
63. Díaz, A.B.; De Ory, I.; Caro, I.; Blandino, A. Enhance Hydrolytic Enzymes Production by Aspergillus Awamori on Supplemented Grape Pomace. Food Bioprod. Process.; 2012; 90, pp. 72-78. [DOI: https://dx.doi.org/10.1016/j.fbp.2010.12.003]
64. Brijwani, K.; Oberoi, S.; Vadlani, P.V.; Oberoi, H.S.; Vadlani, P.V. Production of a Cellulolytic Enzyme System in Mixed-Culture Solid-State Fermentation of Soybean Hulls Supplemented with Wheat Bran. Process Biochem.; 2010; 45, pp. 120-128. [DOI: https://dx.doi.org/10.1016/j.procbio.2009.08.015]
65. Diaz, A.B.; Blandino, A.; Webb, C.; Caro, I. Modelling of Different Enzyme Productions by Solid-State Fermentation on Several Agro-Industrial Residues. Appl. Microbiol. Biotechnol.; 2016; 100, pp. 9555-9566. [DOI: https://dx.doi.org/10.1007/s00253-016-7629-y] [PubMed: https://www.ncbi.nlm.nih.gov/pubmed/27306907]
66. Verduzco-Oliva, R.; Gutierrez-Uribe, J.A. Beyond Enzyme Production: Solid State Fermentation (SSF) as an Alternative Approach to Produce Antioxidant Polysaccharides. Sustainability; 2020; 12, 495. [DOI: https://dx.doi.org/10.3390/su12020495]
67. Mansour, A.A.; Arnaud, T.; Lu-Chau, T.A.; Fdz-Polanco, M.; Moreira, M.T.; Rivero, J.A.C. Review of Solid State Fermentation for Lignocellulolytic Enzyme Production: Challenges for Environmental Applications. Rev. Environ. Sci. Biotechnol.; 2016; 15, pp. 31-46. [DOI: https://dx.doi.org/10.1007/s11157-016-9389-7]
68. Yazid, N.A.; Barrena, R.; Komilis, D.; Sánchez, A. Solid-State Fermentation as a Novel Paradigm for Organic Waste Valorization: A Review. Sustainability; 2017; 9, 224. [DOI: https://dx.doi.org/10.3390/su9020224]
69. Bhargav, S.; Panda, B.P.; Ali, M.; Javed, S. Solid-State Fermentation - An Overview. Chem. Biochem. Eng; 2008; 22, pp. 49-70.
70. Marques, N.P.; de Cassia Pereira, J.; Gomes, E.; da Silva, R.; Araújo, A.R.; Ferreira, H.; Rodrigues, A.; Dussán, K.J.; Bocchini, D.A. Cellulases and Xylanases Production by Endophytic Fungi by Solid State Fermentation Using Lignocellulosic Substrates and Enzymatic Saccharification of Pretreated Sugarcane Bagasse. Ind. Crops Prod.; 2018; 122, pp. 66-75. [DOI: https://dx.doi.org/10.1016/j.indcrop.2018.05.022]
71. Cerda, A.; Gea, T.; Vargas-García, M.C.; Sánchez, A. Towards a Competitive Solid State Fermentation: Cellulases Production from Coffee Husk by Sequential Batch Operation and Role of Microbial Diversity. Sci. Total Environ.; 2017; 589, pp. 56-65. [DOI: https://dx.doi.org/10.1016/j.scitotenv.2017.02.184]
72. Zieminski, K.; Romanowska, I.; Kowalska, M.; Ziemiński, K.; Romanowska, I.; Kowalska, M. Enzymatic Pretreatment of Lignocellulosic Wastes to Improve Biogas Production. Waste Manag.; 2012; 32, pp. 1131-1137. [DOI: https://dx.doi.org/10.1016/j.wasman.2012.01.016]
73. Díaz, A.B.; Marzo, C.; Caro, I.; de Ory, I.; Blandino, A. Valorization of Exhausted Sugar Beet Cossettes by Successive Hydrolysis and Two Fermentations for the Production of Bio-Products. Bioresour. Technol.; 2017; 225, pp. 225-233. [DOI: https://dx.doi.org/10.1016/j.biortech.2016.11.024]
74. Rodriguez Couto, S. Exploitation of Biological Wastes for the Production of Value-Added Products Uncler Solid-State Fermentation Conditions. Biotechnol. J.; 2008; 3, pp. 859-870. [DOI: https://dx.doi.org/10.1002/biot.200800031] [PubMed: https://www.ncbi.nlm.nih.gov/pubmed/18543242]
75. Marzo, C.; Díaz, A.B.; Caro, I.; Blandino, A. Valorization of Agro-Industrial Wastes to Produce Hydrolytic Enzymes by Fungal Solid-State Fermentation. Waste Manag. Res.; 2018; 32, pp. 1-8. [DOI: https://dx.doi.org/10.1177/0734242X18798699] [PubMed: https://www.ncbi.nlm.nih.gov/pubmed/30222065]
76. Mouafi, F.E.; Karam, E.A.; Hassan, H.M. Production of Dextranase from Agro-Industrial Wastes by Aspergillus Awamori F-234 under Solid State Fermentation. Res. J. Pharm. Biol. Chem. Sci.; 2016; 7, pp. 1451-1459.
77. Heerd, D.; Diercks-Horn, S.; Fernández-Lahore, M. Efficient Polygalacturonase Production from Agricultural and Agro-Industrial Residues by Solid-State Culture of Aspergillus Sojae under Optimized Conditions. Springerplus; 2014; 3, pp. 1-14. [DOI: https://dx.doi.org/10.1186/2193-1801-3-742] [PubMed: https://www.ncbi.nlm.nih.gov/pubmed/25674471]
78. Bai, Z.H.; Zhang, H.X.; Qi, H.Y.; Peng, X.W.; Li, B.J. Pectinase Production by Aspergillus Niger Using Wastewater in Solid State Fermentation for Eliciting Plant Disease Resistance. Bioresour. Technol.; 2004; 95, pp. 49-52. [DOI: https://dx.doi.org/10.1016/j.biortech.2003.06.006] [PubMed: https://www.ncbi.nlm.nih.gov/pubmed/15207294]
79. Roche, N.; Berna, P.; Desgranges, C.; Durand, A. Substrate Use and Production of α-l-Arabinofuranosidase during Solid-State Culture of Trichoderma Reesei on Sugar Beet Pulp. Enzyme Microb. Technol.; 1995; 17, pp. 935-941. [DOI: https://dx.doi.org/10.1016/0141-0229(94)00132-B]
80. Leung, C.C.J.; Cheung, A.S.Y.; Zhang, A.Y.Z.; Lam, K.F.; Lin, C.S.K.; Chark Joe Leung, C.; Siu Yeung Cheung, A.; Yan-Zhu Zhang, A.; Fung Lam, K.; Sze Ki Lin, C. Utilisation of Waste Bread for Fermentative Succinic Acid Production. Biochem. Eng. J.; 2012; 65, pp. 10-15. [DOI: https://dx.doi.org/10.1016/j.bej.2012.03.010]
81. Pleissner, D.; Kwan, T.H.; Lin, C.S.K. Fungal Hydrolysis in Submerged Fermentation for Food Waste Treatment and Fermentation Feedstock Preparation. Bioresour. Technol.; 2014; 158, pp. 48-54. [DOI: https://dx.doi.org/10.1016/j.biortech.2014.01.139]
82. Kwan, T.H.; Hu, Y.; Lin, C.S.K. Valorisation of Food Waste via Fungal Hydrolysis and Lactic Acid Fermentation with Lactobacillus Casei Shirota. Bioresour. Technol.; 2016; 217, pp. 129-136. [DOI: https://dx.doi.org/10.1016/j.biortech.2016.01.134] [PubMed: https://www.ncbi.nlm.nih.gov/pubmed/26873283]
83. Dessie, W.; Zhang, W.; Xin, F.; Dong, W.; Zhang, M.; Ma, J.; Jiang, M. Succinic Acid Production from Fruit and Vegetable Wastes Hydrolyzed by On-Site Enzyme Mixtures through Solid State Fermentation. Bioresour. Technol.; 2018; 247, pp. 1177-1180. [DOI: https://dx.doi.org/10.1016/j.biortech.2017.08.171] [PubMed: https://www.ncbi.nlm.nih.gov/pubmed/28941663]
84. Marzo, C.; Díaz, A.B.; Caro, I.; Blandino, A. Conversion of Exhausted Sugar Beet Pulp into Fermentable Sugars from a Biorefinery Approach. Foods; 2020; 9, 1351. [DOI: https://dx.doi.org/10.3390/foods9101351]
85. García, C.; Bautista, L.; Rendueles, M.; Díaz, M. A New Synbiotic Dairy Food Containing Lactobionic Acid and Lactobacillus Casei. Int. J. Dairy Technol.; 2019; 72, pp. 47-56. [DOI: https://dx.doi.org/10.1111/1471-0307.12558]
86. Shafi, A.; Naeem Raja, H.; Farooq, U.; Akram, K.; Hayat, Z.; Naz, A.; Nadeem, H.R. Antimicrobial and Antidiabetic Potential of Synbiotic Fermented Milk: A Functional Dairy Product. Int. J. Dairy Technol.; 2019; 72, pp. 15-22. [DOI: https://dx.doi.org/10.1111/1471-0307.12555]
87. Silva, H.L.A.; Balthazar, C.F.; Silva, R.; Vieira, A.H.; Costa, R.G.B.; Esmerino, E.A.; Freitas, M.Q.; Cruz, A.G. Sodium Reduction and Flavor Enhancer Addition in Probiotic Prato Cheese: Contributions of Quantitative Descriptive Analysis and Temporal Dominance of Sensations for Sensory Profiling. J. Dairy Sci.; 2018; 101, pp. 8837-8846. [DOI: https://dx.doi.org/10.3168/jds.2018-14819]
88. Cubas-Cano, E.; González-Fernández, C.; Ballesteros, M.; Tomás-Pejó, E. Biotechnological Advances in Lactic Acid Production by Lactic Acid Bacteria: Lignocellulose as Novel Subtrate. Biofuels Bioprod. Biorefining; 2018; 12, pp. 290-303. [DOI: https://dx.doi.org/10.1002/bbb.1852]
89. Ahmed, T.; Shahid, M.; Azeem, F.; Rasul, I.; Shah, A.A.; Noman, M.; Hameed, A.; Manzoor, N.; Manzoor, I.; Muhammad, S. Biodegradation of Plastics: Current Scenario and Future Prospects for Environmental Safety. Environ. Sci. Pollut. Res.; 2018; 25, pp. 7287-7298. [DOI: https://dx.doi.org/10.1007/s11356-018-1234-9]
90. López-Gómez, J.P.; Pérez-Rivero, C.; Venus, J. Valorisation of Solid Biowastes: The Lactic Acid Alternative. Process Biochem.; 2020; 99, pp. 222-235. [DOI: https://dx.doi.org/10.1016/j.procbio.2020.08.029]
91. Masutani, K.; Kimura, Y. Synthesis, Structure and Properties of Poly (Lactic Acid); Springer: Berlin/Heidelberg, Germany, 2018; Volume 279, ISBN 978-3-319-64229-1
92. Tan, J.; Abdel-Rahman, M.A.; Sonomoto, K. Biorefinery-Based Lactic Acid Fermentation: Microbial Production of Pure Monomer Product. Advances in Polymer Science; Springer: New York, NY, USA, 2018; Volume 279, pp. 27-66.
93. Nancib, A.; Nancib, N.; Meziane-Cherif, D.; Boubendir, A.; Fick, M.; Boudrant, J. Joint Effect of Nitrogen Sources and B Vitamin Supplementation of Date Juice on Lactic Acid Production by Lactobacillus Casei Subsp. Rhamnosus. Bioresour. Technol.; 2005; 96, pp. 63-67. [DOI: https://dx.doi.org/10.1016/j.biortech.2003.09.018]
94. Marzo, C.; Díaz, A.B.; Caro, I.; Blandino, A. Valorisation of Fungal Hydrolysates of Exhausted Sugar Beet Pulp for Lactic Acid Production. J. Sci. Food Agric.; 2021; 101, pp. 4108-4117. [DOI: https://dx.doi.org/10.1002/jsfa.11046] [PubMed: https://www.ncbi.nlm.nih.gov/pubmed/33368320]
95. Díaz, A.B.; González, C.; Marzo, C.; Caro, I.; Blandino, A. Feasibility of Exhausted Sugar Beet Pulp as Raw Material for Lactic Acid Production. J. Sci. Food Agric.; 2020; 100, pp. 3036-3045. [DOI: https://dx.doi.org/10.1002/jsfa.10334]
96. Alexandri, M.; Hübner, D.; Schneider, R.; Fröhling, A.; Venus, J. Towards Efficient Production of Highly Optically Pure D-Lactic Acid from Lignocellulosic Hydrolysates Using Newly Isolated Lactic Acid Bacteria. New Biotechnol.; 2022; 72, pp. 1-10. [DOI: https://dx.doi.org/10.1016/j.nbt.2022.08.003]
97. Oliveira, R.A.; Schneider, R.; Lunelli, B.H.; Rossell, C.E.V.; Filho, R.M.; Venus, J. A Simple Biorefinery Concept to Produce 2G-Lactic Acid from Sugar Beet Pulp (SBP): A High-Value Target Approach to Valorize a Waste Stream. Molecules; 2020; 25, 2113. [DOI: https://dx.doi.org/10.3390/molecules25092113]
98. Santosh, I.; Ashtavinayak, P.; Amol, D.; Sanjay, P. Enhanced Bioethanol Production from Different Sugarcane Bagasse Cultivars Using Co-Culture of Saccharomyces Cerevisiae and Scheffersomyces (Pichia) Stipitis. J. Environ. Chem. Eng.; 2017; 5, pp. 2861-2868. [DOI: https://dx.doi.org/10.1016/j.jece.2017.05.045]
99. Cui, F.; Li, Y.; Wan, C. Lactic Acid Production from Corn Stover Using Mixed Cultures of Lactobacillus Rhamnosus and Lactobacillus Brevis. Bioresour. Technol.; 2011; 102, pp. 1831-1836. [DOI: https://dx.doi.org/10.1016/j.biortech.2010.09.063]
100. Berlowska, J.; Cieciura, W.; Borowski, S.; Dudkiewicz, M.; Binczarski, M.; Witonska, I.; Otlewska, A.; Kregiel, D. Simultaneous Saccharification and Fermentation of Sugar Beet Pulp with Mixed Bacterial Cultures for Lactic Acid and Propylene Glycol Production. Molecules; 2016; 21, 1380. [DOI: https://dx.doi.org/10.3390/molecules21101380]
101. Lemoigne, M. Produits de Deshydration et de Polymerisation de l’acide Β= Oxybutyrique. Bull. Soc. Chim. Biol.; 1926; 8, pp. 770-782.
102. Muneer, F.; Rasul, I.; Azeem, F.; Siddique, M.H.; Zubair, M.; Nadeem, H. Microbial Polyhydroxyalkanoates (PHAs): Efficient Replacement of Synthetic Polymers. J. Polym. Environ.; 2020; 28, pp. 2301-2323. [DOI: https://dx.doi.org/10.1007/s10924-020-01772-1]
103. Jiang, G.; Hill, D.J.; Kowalczuk, M.; Johnston, B.; Adamus, G.; Irorere, V.; Radecka, I. Carbon Sources for Polyhydroxyalkanoates and an Integrated Biorefinery. Int. J. Mol. Sci.; 2016; 17, 1157. [DOI: https://dx.doi.org/10.3390/ijms17071157]
104. Bertrand, J.L.; Ramsay, B.A.; Chavarie, C. Biosynthesis of Poly-β-Hydroxyalkanoates from Pentoses by Pseudomonas Pseudoflava. Appl. Environ. Microbiol.; 1990; 56, pp. 3133-3138. [DOI: https://dx.doi.org/10.1128/aem.56.10.3133-3138.1990] [PubMed: https://www.ncbi.nlm.nih.gov/pubmed/16348320]
105. Laycock, B.; Halley, P.; Pratt, S.; Werker, A.; Lant, P. The Chemomechanical Properties of Microbial Polyhydroxyalkanoates. Prog. Polym. Sci.; 2013; 38, pp. 536-583. [DOI: https://dx.doi.org/10.1016/j.progpolymsci.2012.06.003]
106. Pakalapati, H.; Chang, C.K.; Show, P.L.; Arumugasamy, S.K.; Lan, J.C.W. Development of Polyhydroxyalkanoates Production from Waste Feedstocks and Applications. J. Biosci. Bioeng.; 2018; 126, pp. 282-292. [DOI: https://dx.doi.org/10.1016/j.jbiosc.2018.03.016]
107. Kurt-Kızıldoğan, A.; Türe, E.; Okay, S.; Otur, Ç. Improved Production of Poly(3-Hydroxybutyrate) by Extremely Halophilic Archaeon Haloarcula Sp. TG1 by Utilization of RCKT3eng-Treated Sugar Beet Pulp. Biomass Convers. Biorefinery; 2021; [DOI: https://dx.doi.org/10.1007/s13399-021-02011-w]
108. Jeffries, T.W. Utilization of Xylose by Bacteria, Yeasts, and Fungi. Adv. Biochem. Eng. Biotechnol.; 1983; 27, pp. 1-32. [DOI: https://dx.doi.org/10.1007/BFb0009101]
109. Dietrich, K.; Dumont, M.J.; Del Rio, L.F.; Orsat, V. Sustainable PHA Production in Integrated Lignocellulose Biorefineries. New Biotechnol.; 2019; 49, pp. 161-168. [DOI: https://dx.doi.org/10.1016/j.nbt.2018.11.004]
110. Pohlmann, A.; Fricke, W.F.; Reinecke, F.; Kusian, B.; Liesegang, H.; Cramm, R.; Eitinger, T.; Ewering, C.; Pötter, M.; Schwartz, E. et al. Genome Sequence of the Bioplastic-Producing “Knallgas” Bacterium Ralstonia Eutropha H16. Nat. Biotechnol.; 2006; 24, pp. 1257-1262. [DOI: https://dx.doi.org/10.1038/nbt1244]
111. Cesário, M.T.F.; de Almeida, M.C.M.D. Lignocellulosic Hydrolysates for the Production of Polyhydroxyalkanoates. Microorganisms in Biorefineries; Springer: Berlin/Heidelberg, Germany, 2015; pp. 79-104.
112. Lu, X.; Liu, G.; Wang, Y.; Ding, J.; Weng, W. Engineering of an L-Arabinose Metabolic Pathway in Ralstonia Eutropha W50. Wei Sheng Wu Xue Bao; 2013; 53, pp. 1267-1275.
113. Cieciura-Włoch, W.; Borowski, S.; Domański, J. Dark Fermentative Hydrogen Production from Hydrolyzed Sugar Beet Pulp Improved by Nitrogen and Phosphorus Supplementation. Bioresour. Technol.; 2021; 340, 125622. [DOI: https://dx.doi.org/10.1016/j.biortech.2021.125622]
114. Carvalheira, M.; Marreiros, B.C.; Reis, M. Acids (VFAs) and Bioplastic (PHA) Recovery. Clean Energy and Resource Recovery; Elsevier: Amsterdam, The Netherlands, 2022; pp. 245-254. ISBN 9780323901789
© 2023 by the authors. Licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license (https://creativecommons.org/licenses/by/4.0/). Notwithstanding the ProQuest Terms and Conditions, you may use this content in accordance with the terms of the License.
Details
; Díaz, Ana Belén
; Blandino, Ana