Sub-Nanosecond Single Mode-Locking Pulse Generation in an Idler-Resonant Intracavity KTA Optical Parametric Oscillator Driven by a Dual-Loss-Modulated Q-Switched and Mode-Locked Laser with an Acousto-Optic Modulator and MoWS2

Abstract

The synthesis of 2D MoWS₂ nanosheets involved the liquid-phase exfoliation technique was explored in this paper. The nonlinear optical response of MoWS₂ was characterized in the 1 µm wavelength range, and its suitability as a saturable absorber (SA) was confirmed. Experimental demonstrations were conducted by using MoWS₂ as an SA in an idler-resonant intracavity KTA optical parametric oscillator (OPO) driven by a dual-loss-modulated Q-switched and mode-locked (QML) YVO₄/Nd:YVO₄ laser with an acousto-optic modulator (AOM). By appropriately tuning the pump power and the AOM repetition rate, the Q-switched envelope pulse widths for the signal and idler waves could be significantly reduced to be shorter than the cavity round-trip transit time, i.e., the interval between two neighboring mode-locking pulses. Consequently, this enabled the generation of sub-nanosecond single mode-locking pulses with a low repetition rate, high pulse energy, and remarkable stability. With a repetition rate of 1 kHz and maximal pulse energies of 318 µJ and 169 µJ, respectively, sub-nanosecond single mode-locking pulses of the signal and idler waves were generated. The theoretical model was established using coupled rate equations with a Gaussian spatial distribution approximation. The numerical simulation results for generating sub-nanosecond single mode-locking pulses for the signal and idler waves within their respective Q-switched envelopes aligned fundamentally with the experimental results, proving that MoWS₂ can be a potential nanomaterial for further optoelectronic applications.

1. Introduction

Sub-nanosecond eye-safe near-infrared (1.5 µm) and mid-infrared (3–5 µm) lasers with high pulse energy, stability, and a low repetition rate offer significant advantages for various practical applications, including atmospheric monitoring, remote sensing, and optoelectronic countermeasures [1,2]. The use of nonlinear optical (NLO) crystals allows for the effective generation of near-infrared and mid-infrared lasers through nonlinear frequency conversion. Among these methods, the optical parametric oscillator (OPO) stands out for its compact, simple, and robust configuration, making it a widely used tool in infrared laser applications. The continuous-wave mode-locking (CWML) technique is commonly applied to generate ultrashort pulses. However, in CWML lasers, the energy for each pulse is relatively low due to the high repetition rate. For CWML lasers, the typical pulse energy varies from pJ to tens of nJ, whereas the repetition rate is typically restricted by the cavity length and measured in tens of MHz. Additionally, the high repetition rate can lead to significant thermal lensing, resulting in heat accumulation in materials during optical nonlinearity measurements. To address this, efforts have been made to develop single passively Q-switched and mode-locked (QML) lasers. These QML lasers operate with a repetition rate primarily determined by saturable absorption. However, achieving a modulation depth close to 100% with these lasers remains a challenge, and maintaining amplitude stability beneath the Q-switched envelope is an ongoing concern.

The integration of an active modulator into a passively QML laser, termed dual-loss modulation [3,4], allows control over the envelope’s repetition rate. In dual-loss-modulated QML lasers, the Q-switched envelope’s repetition rate is regulated by the active modulator, while the mode-locking (ML) pulses depend on both the active modulation and the saturable absorption, leading to a 100% modulation depth. However, given the presence of multiple ML pulses within a Q-switched envelope, the average peak power for these ML pulses tends to be relatively low, typically in the range of 0.1 to tens of kW. This limitation has prompted efforts to achieve higher peak power ML lasers by reducing the number of ML pulses within a Q-switched envelope. The dual-loss-modulated QML laser, distinguished by its high peak power, sub-nanosecond pulse duration, and precise repetition rate adjustment, has emerged as an exceptional pump source for intracavity OPOs (IOPOs). Consequently, an IOPO pumped by a dual-loss-modulated QML laser has been proposed, with both theoretical simulations and experimental results demonstrating the generation of a signal beam characterized by a narrow pulse width and high average power [5].

In recent years, a variety of one-dimensional and two-dimensional (2D) nanomaterials have emerged and developed as potential candidates for OPO systems driven by Nd-doped lasers. These materials include carbon nanotubes [6], graphene [7], and transition metal dichalcogenides (TMDs) [8]. Among the TMDs, novel alloyed TMD species have gained significant interest due to their thermodynamic reliability, intriguing electrical characteristics, and layer-dependent properties [9,10,11]. These alloyed TMDs offer extensive possibilities for various applications such as field-effect transistors [12], hydrogen evolution catalysts [13], and optoelectronic devices [14]. For instance, it has been demonstrated that the band gap of 2D Mo_(1−x)W_xS₂ monolayer alloys can be adjusted from 1.82 eV (x = 0.2) to 1.99 eV (x = 1) by altering the elemental composition [15]. Such enhanced freedom introduced by alloying components might significantly improve the performance of ultrashort laser pulse generation. Mo_(1−x)W_xS₂ alloys have been theoretically and experimentally proven to possess broadband saturable absorption characteristics, serving as promising saturable absorbers (SAs) [16,17,18,19]. Yan et al. reported a passively Q-switched Er:YAG laser employing multilayer Mo_0.5W_0.5S₂ (MoWS₂), generating microsecond pulses at 1645 nm [16]. Ahmad et al. demonstrated passively Q-switched fiber lasers at various wavelengths using Mo_0.8W_0.2S₂ thin films [17,18]. Niu et al. presented a 2 μm doubly Q-switched mode-locked (DQML) Tm:YAP laser incorporating an electro-optic modulator and Mo_0.5W_0.5S₂ SA, achieving a pulse width of 205 ns and a peak power of 2.44 kW [19]. However, to the best of our knowledge, there has been no associated experimental study or accompanying theoretical analysis on OPOs driven by QML Nd-doped solid-state lasers based on ternary Mo_(1−x)W_xS₂ alloys.

In this paper, 2D MoWS₂ nanosheets were synthesized through the liquid-phase exfoliation method, followed by an evaluation of their nonlinear optical response. An LD-pumped idler-resonant KTA-based IOPO driven by a dual-loss-modulated QML laser with an acousto-optic modulator (AOM) and MoWS₂ SA was constructed within this research framework. Under a certain pump power, sub-nanosecond single mode-locking pulses of the signal and idler waves were obtained, respectively. Leveraging the QML pulses’ fluctuation mechanism and assuming a Gaussian spatial distribution, a set of coupled rate equations governing the diode-pumped idler-resonant IOPO, driven by a dual-loss-modulated QML laser with AOM and MoWS₂ SA, were derived. Our numerical simulation results are fundamentally in agreement with the experimental values. These investigations underscore the promising potential of MoWS₂ as a highly effective nanomaterial for advanced ultrafast solid-state laser systems.

2. Materials and Methods

2.1. Fabrication and Characterizations of 2D MoWS₂ SA

A liquid-phase exfoliation process was employed to produce MoWS₂ nanosheets [20]. Initially, 10 mg of synthesized MoWS₂ single crystals (synthesized by chemical-vapor transport technique [21]) were dispersed in 10 mL of isopropyl alcohol. Ultrasonic vibration was employed for 6 h to facilitate the exfoliation of nanosheets, followed by centrifugal separation at 6000 rpm for 15 min. The glass output coupler was placed at the center of a rotating plate with a speed of 300 rpm, and 20 µL of MoWS₂ nanosheet liquid supernatant was spin-coated onto its surface. Finally, MoWS₂ SA samples were obtained by drying them at ambient temperature.

Crystallographic characteristics of the MoWS2 crystal were analyzed using X-ray diffraction (XRD). As shown in Figure 1a, the phase structure investigation confirms that the sample comprises a single-phase 2H-type material [22], aligning with previous studies [23]. Furthermore, Raman spectrum analysis was conducted on the synthesized MoWS₂ sample using LabRAM HR Evolution Raman spectroscopy at a wavelength of 532 nm. Figure 1b illustrates the Raman spectrum displaying peaks at 350 cm⁻¹, 375.5 cm⁻¹, and 412.8 cm⁻¹, with full width at half maximum (FWHM) values of 14.6, 15.7, and 16.6 cm⁻¹, respectively. The first two peaks correspond to the E¹_2g and A¹_g modes, respectively. Typically, the standard Mo-S structure exhibits peaks at 407 and 374 cm⁻¹ [24]. However, upon W-atom doping, observed peak shifts occur, including the emergence of a third peak at 412.8 cm⁻¹, indicating the presence of the W-S structure. The scanning electron microscope (SEM) and energy dispersive spectrometer (EDS) mapping patterns in Figure 1c further validate the uniform distribution of the three components. Additionally, morphological images reveal the material’s layered nanostructure properties. Figure 1d,e presents transmission electron microscope (TEM) images at different size scales. These images distinctly display nanostructures with an interlayer spacing of 0.62 nm, clearly visible in the high-resolution TEM image. The observed distance of 0.27 nm corresponds to the (100) plane of MoWS₂, similar to MoS₂ or WS₂, suggesting lattice structures akin to those found in these materials [25]. The dimensions of the synthesized MoWS₂ were further characterized using atomic force microscopy (AFM), depicted in Figure 1f. The material exhibited a thickness of approximately 10 nm with a lateral size of ~µm. It can be concluded that few-layer MoWS₂ nanosheets are successfully exfoliated using the liquid-phase exfoliation method.

The optical responses of MoWS₂ are delineated in Figure 2. Utilizing a UV–Vis–NIR spectrophotometer, the MoWS₂ SA demonstrated consistent broadband optical absorption across a wavelength spectrum ranging from 400 to 1850 nm. However, a notable reduction in the absorption spectrum was observed specifically in the wavelength range from 1300 to 1600 nm, as portrayed in the inset in Figure 2a. At sufficiently high excitation levels, the MoWS₂ SA showcased intensity-dependent transmittance due to the Pauli blocking principle. To elucidate the nonlinear absorption characteristics of MoWS₂ SA, a balanced twin detector experiment was conducted using a custom-built Nd-doped Q-switching laser source with a 50 ns pulse width. This experimental setup allows the derivation of parameters such as the non-saturable absorption loss ${\alpha }_{NS}$, the modulation depth $\mathrm{\Delta }T$, and the saturated optical intensity $I_{sat}$, which can be computed using the following formula [26]:

(1)$T=1-{\alpha }_{NS}-\mathrm{\Delta }T\exp (-{\displaystyle \frac{I}{I_{sat}}}),$

The nonlinear parameter at a specific position encapsulates the collective effect of numerous MoWS₂ nanosheets with varying thicknesses within the irradiation spot, spanning approximately hundreds of microns. By fitting the experimental data of the nonlinear transmittance showcased in Figure 2b, the intensity-independent ${\alpha }_{NS}$ is determined to be 9.59%. Additionally, the $\mathrm{\Delta }T$ is estimated to be 9.12%, while the $I_{sat}$ is approximately 3.89 MW/cm². The inset in Figure 2b exhibits a linear relationship between transmittance and peak-energy density at low-power levels, where a slope of 1.56 is obtained through linear regression. These characteristics highlight the promising potential of MoWS₂ SA in generating laser pulses. The MoWS₂ SA used in this study had a thickness of approximately 10 nm. Despite the significant absorption observed, the high damage threshold of MoWS₂ SA, combined with appropriate thermal management and operation within safe pump intensities, ensures the longevity of the SA without significant risk of long-term damage.

Given that the ground-state population density $n_{s0}$, the cross-sections of the excited state absorption (ESA) ${\sigma }_e$, and the ground-state absorption (GSA) ${\sigma }_g$ constitute the sources of the small-signal transmittance $T_0$ and the maximum transmittance $T_{\max }$ actions, the correlation parameters of MoWS₂ SA can be determined using the following equations [8]:

(2)${\displaystyle \frac{{\sigma }_g}{{\sigma }_e}}={\displaystyle \frac{\ln T_0}{\ln T_{\max }}},$

(3)${\displaystyle \frac{({\sigma }_g-{\sigma }_e)\times T_0}{hv}}=k,$

(4)$T_0=\exp (-n_{s0}{\sigma }_g{l}_{sa}),$

(5)$T_{\max }=\exp (-n_{s0}{\sigma }_e{l}_{sa}),$

where $h$ stands for the Planck constant and $l_{sa}$ is the thickness of MoWS₂ SA (~10 nm). According to the information available in Figure 2b, the $T_0$ at low power density, the $T_{\max }$ at high power density, and the slope k can be discerned, and the calculated results indicate that ${\sigma }_g$ is 6.98 × 10⁻¹⁹ cm², ${\sigma }_e$ is 3.4 × 10⁻¹⁹ cm², and $n_{s0}$ is 2.968 × 10²³ cm⁻³, respectively. Considering the inhomogeneous broadening mechanism, it is determined that the excited-state lifetime ${\tau }_s$ of the MoWS₂ SA is 714.1 µs [8]. Table 1 presents the key parameters concerning the saturable absorption characteristics of 2D MoWS₂ SA.

2.2. Experimental Setup

Figure 3 depicts the schematic of the experimental setup. Considering thermal lensing, cavity stability, and fundamental beam waist concerns, we designed a linear Z-cavity based on the ABCD transmission matrix theory [27]. We adopted a Z-type folded cavity for the fundamental wave cavity, with a length of 119.5 cm, alongside an idler-resonant OPO cavity length of 3.8 cm. The laser system was powered by a commercial fiber-coupled diode laser (FAP system, COHERENT Inc., Saxonburg, PA, USA) at a central wavelength of 808 nm. An optical re-imaging system focused the diode laser into the laser crystal, generating a pump beam with a beam radius around 200 μm. An a-cut composite crystal YVO₄/Nd:YVO₄ with dimensions of 3 mm × 3 mm × (2 + 10) mm and Nd-doping concentration of 0.3 at% was utilized as the laser medium. Both surfaces of the YVO₄/Nd:YVO₄ crystal were polished and anti-reflection (AR)-coated at 808 and 1064 nm. The nonlinear crystal KTA with dimensions of 5 mm × 5 mm × 20 mm was cut for type-II noncritical phase-matching configuration (θ = 90°, ϕ = 0°) for optimal effective nonlinear coefficient and acceptance angle and AR-coated at 1064 and 1535 nm (R < 0.2%) and high-transmission (HT)-coated at 3470 nm (T > 95%) on both sides. A 47-mm-long AOM (GSQ27-3, central frequency: 27.12 MHz, RF power: 50 W, 26th Institute, CETC, Beijing, China) with AR-coated at 1064 nm (R < 0.2%) on both surfaces served as the active modulator, capable of modulation repetition rates from 1 to 50 kHz. To manage heat dispersion, the laser medium and KTA crystals were wrapped with a thin layer of indium foil, placed in copper holders, and cooled via a thermoelectric cooler at 16 °C for stable laser output. The as-prepared MoWS₂ was employed as the SA in the fundamental laser system. The lengths of the three cavity arms (L₁, L₂, and L₃) were 40.2, 68.5, and 10.8 cm, respectively, corresponding to a fundamental wave’s round-trip time of approximately 8.26 ns. Optimizing the cavity length was crucial to minimize the number of ML pulses within a Q-switched envelope. Longer cavities reduced the number of ML pulses but broadened the Q-switched envelope, necessitating theoretical and experimental optimization. As the input mirror, the plane mirror M₁ was AR-coated at 808 nm (R < 0.2%) on its entrance surface, and high-reflectivity (HR)-coated at 1064 nm (R > 99.8%) and HT-coated at 808 nm (T > 97%) on the opposite surface. The folded concave mirrors M₂, with a radius of curvature (ROC) of 500 mm, and M₃, with a ROC of 200 mm, were HR-coated at 1064 nm. The flat mirror M₄ (JGS3) was AR-coated at 1064 nm (R < 0.2%) on its entrance surface, and HT-coated at 1064 nm (T > 99.5%) and HR-coated at both 1535 and 3470 nm (R > 99.8%) on the opposite surface. The flat mirror M₅ (Al₂O₃) was HR-coated at 1064 nm (R > 99.9%), HT-coated at 1535 nm (T > 99.3%), and partial-reflectivity (PR)-coated at 3470 nm (R = 91%). Thus, the idler-resonant OPO cavity oscillated between M₄ and M₅, while the fundamental wave oscillated between M₁ and M₅.

To distinguish between the idler, signal, and residual fundamental waves, optical components were strategically selected. A dichroic mirror DM₁ (HR-coated at both 1535 and 1064 nm and HT-coated at 3470 nm) crafted from CaF₂ was utilized to effectively separate the idler wave. Meanwhile, a dichroic mirror DM₂ (HR-coated at 1535 nm and HT-coated at 1064 nm) made of BK7 glass was employed to differentiate the signal wave from the residual fundamental wave. Precise measurement tools were employed to assess pulse characteristics and wave spectra. A DPO-7104C digital oscilloscope (rise time: 350 ps, 1 GHz bandwidth, 20 G samples/s, Tektronix Inc., Beaverton, OR, USA), a fast InGaAs photodetector with a rising time of 0.4 ns (New Focus, 1611) and a Wavescan laser spectrometer (resolution: 0.4 nm, APE GmbH, Berlin, Germany) were employed to measure the pulse characteristics and the spectrum of the signal wave. The pulse characteristics of the idler wave were acquired by the DPO-7104C digital oscilloscope and an HgCdZnTe photoconductive detector with a response time of 1 ns. The idler wave spectra were measured by another Wavescan MIR laser spectrometer (APE GmbH, Berlin, Germany). Precise measurement of output powers was conducted using a PM100D laser power meter from Thorlabs Inc. (Newton, NJ, USA) to quantify the output powers of both the signal and idler waves.

3. Results and Discussion

In the experiment, the diode-pumped idler-resonant dual-loss-modulated QML YVO₄/Nd:YVO₄/KTA IOPO system operates in two distinct stages: the QML stage and the sub-nanosecond single mode-locking (ML) stage. The experimental results indicated that the primary factors influencing the OPO’s operational status were the active modulation frequency and pump power. The repetition rates of the Q-switched envelopes were controlled by the AOM. During the QML stage, the pulse width of the Q-switched envelope and the number of mode-locking pulses within the Q-switched envelope decrease with increasing pump power and decreasing AOM repetition rate. When the pulse width of the Q-switched envelope becomes shorter than the time interval between two mode-locking pulses, only one mode-locking pulse exists within a Q-switched envelope, marking the transition to the sub-nanosecond single ML stage. At this stage, the OPO output pulses are sub-nanosecond with repetition rates determined by the AOM. The threshold power required for the signal and idler waves was approximately 10.1 W. Figure 4 depicts the average output powers of both the signal and idler waves concerning the pump powers across various modulation frequencies $f_p$. A clear trend is evident, showcasing a consistent rise in the average output powers of both waves with increasing incident pump powers and modulation frequencies. At the point where the pump power reached 21.8 W, the maximum average output powers for the signal wave, observed at modulation frequencies of 1, 2, 3, and 4 kHz, were 318, 364, 398, and 434 mW, respectively. Simultaneously, the corresponding maximum average output powers for the idler wave stood at 169, 194, 206, and 230 mW for the same frequencies.

The experimental results, depicted in Figure 5 using scattered symbols, showcased the durations of the signal and idler waves’ Q-switched envelopes concerning various pump powers for different modulation frequencies $f_p$. For the signal wave’s single ML pulse generation, the experimentally determined threshold powers were 14.68 W for $f_p$ = 1 kHz, 16.16 W for $f_p$ = 2 kHz, 17.05 W for $f_p$ = 3 kHz, and 18.41 W for $f_p$ = 4 kHz. Concurrently, the threshold powers for the idler wave’s single ML pulse generation were 16.16 W for $f_p$ = 1 kHz, 17.05 W for $f_p$ = 2 kHz, 18.41 W for $f_p$ = 3 kHz, and 19.4 W for $f_p$ = 4 kHz. These specific pump powers represent the threshold values for the generation of single ML pulses for the signal and idler waves. It is important to note that the idler-resonant KTA IOPO driven by the dual-loss-modulated QML laser can generate sub-nanosecond single ML pulses of the signal and idler waves only when the pump powers surpass these threshold values. Notably, at equivalent modulation frequencies $f_p$, the threshold power for generating the idler wave’s single ML pulse was marginally higher than that required for the signal wave’s single ML pulse.

The pulse energies of the signal and idler waves’ Q-switched envelopes for different $f_p$ were determined based on the average output powers and the pulse repetition rates, and the results are depicted in Figure 6 using scattered symbols. Specifically, the maximum pulse energies for the signal wave were found to be 318, 182, 132.6, and 108.5 μJ under modulation frequencies of 1, 2, 3, and 4 kHz, respectively. Similarly, for the idler wave, the maximum pulse energies were 169, 97, 68.6, and 57.5 μJ, respectively, at the corresponding frequencies. Hence, it can be inferred that lower repetition rates contribute to enhancing the energies of both the signal and idler waves’ single ML pulses. By employing the durations and energies of the single ML pulses for the signal and idler waves, the estimated peak powers for the signal wave’s single ML pulses were calculated as 441.6, 242.6, 170.1, and 132.3 kW for modulation frequencies of 1, 2, 3, and 4 kHz, respectively. Similarly, the estimated peak powers for the idler wave’s single ML pulses were calculated as 203.6, 111.5, 74.6, and 59.9 kW for the respective modulation frequencies of 1, 2, 3, and 4 kHz, as seen in Figure 7 with scattered symbols.

Figure 8 presents the typical output spectrum of the idler-resonant dual-loss-modulated QML KTA IOPO at an incident pump power of 19.4 W and an AOM modulation rate of 1 kHz. The spectrum exhibited the fundamental and signal waves at 1064 nm and 1535 nm, respectively, while the idler wave was detected at a wavelength of 3467 nm.

In Figure 9a, an extended temporal profile of the idler wave’s sub-nanosecond single ML pulse at $f_p$ = 1 kHz for the pump power of 16.16 W is depicted. The extended oscilloscope trace enables estimation of the ML pulse width, as shown in Figure 9a [28,29]. Based on this trace, the estimated single ML pulse width was approximately 830 ps, corresponding closely to ${\tau }_p$ = 471 ps. Moreover, to illustrate the stability of the single ML pulse IOPO laser, a temporal idler wave’s single ML pulse train, recorded by the digital oscilloscope for $f_p$ = 1 kHz at the pump power of 17.05 W, is displayed in Figure 9b. The pulse-to-pulse amplitude fluctuation, defined as the ratio between the highest deviation and the mean pulse amplitude, measured within the 1 kHz sub-nanosecond idler wave laser pulses, was found to be less than 4%. This result underscores the high stability of the laser output.

Figure 10 and Figure 11 show the oscilloscope traces illustrating the pulses of the signal and idler waves within the idler-resonant dual-loss-modulated QML KTA IOPO at various incident pump powers, while maintaining the AOM’s modulated frequency at 1 kHz, respectively. In particular, observations from Figure 10a–d demonstrate a noticeable trend: The pulse widths of the signal wave’s Q-switched envelopes progressively diminish with increased incident pump power. This reduction results in a corresponding decrease in the number of ML pulses present underneath the Q-switched envelope. Specifically, at pump powers of 11.29 W, 12.52 W, and 14.01 W, there were five, three, and two ML pulses, respectively, coexisting beneath the signal wave’s Q-switched envelope. Remarkably, upon reaching 14.68 W pump power (Figure 10d), it is evident that a single sub-nanosecond ML pulse beneath the Q-switched envelope of the signal wave was successfully achieved.

Furthermore, as showcased in Figure 11, the pulse widths of the idler wave’s Q-switched envelopes decreased consistently with increasing incident pump power. Specifically, at pump powers of 11.29 W, 12.52 W, and 14.68 W, there were eight, six, and two ML pulses, respectively, coexisting beneath the idler wave’s Q-switched envelope. Notably, upon reaching 16.16 W pump power (Figure 11d), it becomes apparent that a single sub-nanosecond ML pulse beneath the idler wave’s Q-switched envelope was successfully achieved.

Additionally, wavelength-tuning in our OPO setup is achieved primarily by adjusting the OPO or using a tunable pump source. In the case of our idler-resonant intracavity KTA OPO, the tuning of the output wavelength is controlled by varying the phase-matching conditions within the nonlinear KTA crystal. This can be realized mainly by temperature tuning or angle tuning. This allows for fine adjustments to the signal and idler wavelengths, thereby enabling tunability of the output wavelength. Additionally, tuning can be achieved by altering the pump power or the cavity configuration, which impacts the gain and resonant conditions of the OPO system. These methods enable broad spectral tunability while maintaining the performance of the 2D MoWS₂ SA. In our experiments, we observed that the pulse widths of the signal and idler waves varied with tuning wavelength due to the wavelength-dependent nonlinear optical properties of the MoWS₂ SA. As the wavelength is tuned, changes in the absorption cross-section and saturation intensity influence the mode-locking dynamics, leading to different pulse durations. Specifically, at shorter wavelengths, the stronger absorption characteristics of MoWS₂ lead to shorter pulse widths due to more efficient mode-locking. Conversely, at longer wavelengths, where the absorption is weaker, the pulse width tends to increase.

4. Theoretical Analysis

In an effort to analyze the dynamic mechanism of the diode-pumped idler-resonant KTA IOPO driven by a doubly QML YVO₄/Nd:YVO₄ laser with AOM and MoWS₂ SA, the coupled rate equations can be utilized to obtain the corresponding characteristics. Based on the fluctuation mechanism [30,31], it is observed that the ML pulse shape remains stable after multiple round-trips within the laser cavity. Employing the assumption of Gaussian spatial distribution, the intracavity photon density corresponding to the TEM₀₀ mode of the fundamental wave can be mathematically described as per [32]:

(6)$\phi (r,t)={\displaystyle \sum _{k=0}{\mathrm{\Phi }}_{k}f(t-t_k)\exp (-\frac{2r^2}{w_l^2})}=\phi (0,t)\exp (-{\displaystyle \frac{2r^2}{w_l^2}}),$

where $\phi (0,t)={\displaystyle {\sum }_{k=0}{\mathrm{\Phi }}_{k}f(t-t_k)}$ represents the photon density along the laser axis, with $w_l$ being the average radius of the TEM₀₀ mode oscillating laser within the cavity. Here, r stands for the radial coordinate, t refers to time, and ${\mathrm{\Phi }}_k$ denotes the relative amplitude of the ML pulses during the kth roundtrip. Additionally, $f(t)={\displaystyle \frac{1}{2\sigma c{\tau }_p}}{\mathrm{sech}}^2({\displaystyle \frac{t}{{\tau }_p}})$ signifies the onset of ML pulses evolving from noise. In relation to the resonator round-trip transit time t_r, $f(t)$ is assumed to be a sharp pulse centered at t = 0, exhibiting a rapid decay within a short duration. In this context, $t_r=2(n_{g}l+n_{sa}{l}_{sa}+n_a{l}_a+n_k{l}_{KTA}+L_c-l-l_{sa}-l_a-l_{KTA})/c$ stands for the round-trip time within the fundamental cavity, where $n_g$, $n_{sa}$, $n_a$, and $n_k$ denote the refractive indices of the gain medium, MoWS₂ SA, AOM crystal, and KTA crystal, respectively. The variables $l$, $l_{sa}$, $l_a$, and $l_{KTA}$ represent the lengths of the gain medium, MoWS₂ SA, AOM crystal, and KTA crystal, while $L_c$ denotes the physical length of the fundamental wave cavity. $c$ stands for the speed of light in vacuum, and ${\tau }_p$ correlates to the FWHM of the ML pulse duration at the fundamental wavelength through the equation $\tau =1.76{\tau }_p$.

Therefore, the temporal photon intensity at different positions within the cavity during the kth roundtrip can be described as follows:

(7)${\phi }_{k,i}={\displaystyle \frac{w_l^2}{w_i^2}}\exp (-{\displaystyle \frac{2r^2}{w_i^2}}){\mathrm{\Phi }}_{k}f(t), (i = g, s, a, k)$

where $w_i$ symbolizes the average beam radii of the TEM₀₀ mode positioned at the gain medium, MoWS₂ SA, AOM crystal, and KTA crystal, respectively. These values can be computed utilizing the ABCD matrix theory.

4.1. Influence of AOM

As an active modulator, an AOM serves to mitigate its intrinsic statistical nature during the initial stages of pulse generation while retaining the nonlinear attributes of the saturable absorber and the Q-switch during the later stages of pulse compression. In each laser shot, the statistical noise pulse, which eventually becomes the ML pulse, undergoes modulation by the active modulator, resulting in an improved stability of pulse energy from shot to shot. The loss function of the AOM can be denoted as ${\delta }_a(t)={\delta }_a\exp (-t^2/t_{ao}^2)$, where ${\delta }_a$ represents the inherent diffraction loss of the AOM, and $t_{ao}$ signifies the turnoff time of the AOM.

Given that the repetition rate of the Q-switched envelopes is reliant on the modulation frequency of the AOM, the initial population inversion density of the laser crystal can be derived. Preceding the onset of a laser pulse, the initial population density at the lower laser level is assumed to be zero for a four-level gain medium. Thus, considering the Boltzmann distribution coefficient f_a in the upper level, the initial population inversion density is expressed as follows [32]:

(8)$n_{initial}=f_a{R}_{in}{\tau }_m\left[1-\exp (-{\displaystyle \frac{1}{f_p{\tau }_m}})\right],$

where $f_p$ denotes the modulation frequency of the AOM and ${\tau }_m$ represents the lifetime of the upper laser level of the laser medium. Additionally, $R_{in}(r)={\displaystyle \frac{P_{in}\exp (-2r^2/w_{in}^2)\left[1-\exp (-\alpha l)\right]}{h{v}_{in}\pi w_{in}^{2}l}}$ signifies the pump rate, where $P_{in}$ is the pump power, $h{v}_{in}$ denotes the single-photon energy of the pump light, $w_{in}$ represents the average radius of the pump beam, and $\alpha$ signifies the absorption coefficient of the gain medium.

4.2. Signal Wave’s Photon Density

In our idler-resonant IOPO, it functions as a pure singly-resonant oscillator (SRO) where the output coupler remains perfectly transparent for the signal wave. This signifies that the signal wave does not undergo the cavity. Similarly, in the context of most second harmonic generation (SHG) processes, the frequency-doubled laser also experiences no cavity, akin to the behavior of the signal wave in our IOPO. Hence, the dynamic process governing the signal wave generation in the idler-resonant IOPO is applicable when considering the SHG process of the frequency-doubling laser. Under these analogous scenarios, the photon density of the signal wave can be formulated as follows [33]:

(9)${\phi }_s(0,t)={\displaystyle \frac{ћ{\mu }_0{d}_{eff}^2{\omega }_f{\omega }_s{\omega }_{id}}{4n_f^2{n}_i^2}}{(2l_{KTA})}^2\phi (0,t){\phi }_{id}(0,t),$

where ${\mu }_0$ denotes the permeability of vacuum, while ${\omega }_{f,s,id}$ represent the circular frequencies corresponding to the fundamental, signal, and idler waves, respectively. The effective nonlinear coefficient is symbolized as d_eff, whereas $n_{f,i}$ stand for the refractive indices of the fundamental and idler waves in the KTA medium, respectively.

4.3. Rate Equations

The interaction between the fundamental and idler waves exclusively took place within the OPO cavity. To reflect this, we introduced a gate function that altered the coupled rate equations:

(10)$G(t)=\left\{\begin{array}{l}1,t_k<t<t_k+t_{rs}\\ 0,t_k+t_{rs}<t<t_{k+1}\end{array}\right.,$

Simultaneously, considering the transmission surpassing 99.3% at the signal wave by the output coupler (M₅), it effectively arrested the evolutionary process of the signal wave field within the idler-resonant IOPO. Given this aspect, the coupled rate equations governing the idler-resonant IOPO are formulated by amalgamating the rate equations characterizing the diode-pumped dual-loss-modulated QML laser involving AOM and MoWS₂ SA [31] with the equations relevant to the IOPOs [34]:

(11)$$\begin{gathered} {\displaystyle \frac{d\phi (r,t)}{dt}}={\displaystyle \int \frac{1}{t_r}}\left\{2\sigma n(r,t)l{\phi }_g(r,t)\right.-2{\sigma }_g{n}_{s1}(r,t)l_s{\phi }_s(r,t)-2{\sigma }_e\left[n_{s0}-n_{s1}(r,t)\right]l_s{\phi }_s(r,t) \\ \left.-{\delta }_a(t){\phi }_a(r,t)-L\phi (r,t)-2{\sigma }_{opo}c{l}_{KTA}{\phi }_k(r,t){\phi }_{id}(r,t)\right\}2\pi rdr, \end{gathered}$$

(12)${\displaystyle \frac{dn(r,t)}{dt}}=R_{in}(r)-\sigma cn(r,t){\phi }_g(r,t)-{\displaystyle \frac{n(r,t)}{\tau }},$

(13)${\displaystyle \frac{d{n}_{s1}(r,t)}{dt}}={\displaystyle \frac{n_{s0}-n_{s1}(r,t)}{{\tau }_s}}-{\sigma }_{g}c{n}_{s1}(r,t){\phi }_s(r,t),$

(14)${\displaystyle \frac{d{\phi }_{id}(r,t)}{dt}}={\displaystyle \int \frac{1}{t_{rid}}}\left\{2{\sigma }_{opo}c{l}_{KTA}{\phi }_k(r,t){\phi }_{id}(r,t)\right.G(t)\left.-\left[L_{id}+\ln \left({\displaystyle \frac{1}{R_{id}}}\right)\right]{\phi }_{id}(r,t)\right\}2\pi rdr,$

where $n(r,t)$ denotes the average population-inversion density, while $\sigma$ represents the stimulated emission cross-section of the gain medium. Additionally, ${\sigma }_g$ and ${\sigma }_e$ stand for the cross-sections related to the GSA and ESA of the MoWS₂ SA. Moreover, $n_{s0}$ and $n_{s1}(r,t)$ signify the population densities pertaining to the ground-state and the excited-state of the MoWS₂ SA. The variables ${\phi }_i(r,t)$ (i = g, s, a, k) indicate the photon densities located at the positions of the gain medium, MoWS₂ SA, AOM crystal, and KTA crystal, respectively, obtainable through the utilization of Equation (7). Furthermore, ${\phi }_{id}(r,t)$ symbolizes the idler wave photon density, whereas ${\sigma }_{opo}=2{\pi }^2{d}_{eff}^{2}h{v}_f{v}_s{v}_i{l}_{KTA}/\left({\epsilon }_0{n}_f^2{n}_i^2{n}_s{l}_f{c}^2\right)$ represents the parametric gain coefficient, with $v_{f,s,i}$ being the frequencies of the fundamental, signal, and idler waves, respectively. Moreover, $n_s$ denotes the refractive index of the signal wave in the KTA crystal. $L$ represents the intrinsic loss for the fundamental wave, while $\tau$ stands for the stimulated-radiation lifetime of the gain medium. Additionally, ${\tau }_s$ and $t_{rid}$ correspond to the excited-state lifetime of the MoWS₂ SA and the round-trip time of the idler wave, respectively. Furthermore, $L_{id}$ denotes the intrinsic loss of the idler wave, and $R_{id}$ stands for the reflectivity at the idler wave of the output coupler.

To simplify, we make the assumption that the modes of the fundamental and idler waves inside the KTA crystal exhibit significant overlap, i.e., $w_k=w_{id}$. Under this particular condition, at the kth round-trip time $t_k=k{t}_r$, the rate equations can be further articulated as:

(15)$$\begin{gathered} {\mathrm{\Phi }}_k={\mathrm{\Phi }}_{k-1}\exp \left\{{\displaystyle \frac{2}{\pi w_l^2}}{\displaystyle \int \left[2\sigma n(r,t_k)\right.}\right.l{\displaystyle \frac{w_l^2}{w_g^2}}\exp \left(-{\displaystyle \frac{2r^2}{w_g^2}}\right) \\ -2{\sigma }_g{n}_{s1}(r,t_k)l_{sa}{\displaystyle \frac{w_l^2}{w_s^2}}\exp \left(-{\displaystyle \frac{2r^2}{w_s^2}}\right) \\ -2{\sigma }_e\left(n_{s0}-n_{s1}(r,t_k)\right)l_{sa}{\displaystyle \frac{w_l^2}{w_s^2}}\exp \left(-{\displaystyle \frac{2r^2}{w_s^2}}\right) \\ -{\delta }_a{\displaystyle \frac{w_l^2}{w_a^2}}\exp \left(-{\displaystyle \frac{2r^2}{w_a^2}}\right)-Lxp\left(-{\displaystyle \frac{2r^2}{w_l^2}}\right) \\ \left.\left.-2{\sigma }_{opo}c{l}_{KTA}{\displaystyle \frac{w_l^2}{w_k^2}}{\varphi }_{id}(0,t_k)\exp \left(-{\displaystyle \frac{4r^2}{w_k^2}}\right)\right]2\pi r\right\}dr, \end{gathered}$$

(16)$$\begin{gathered} n(r,t_k)=\exp \left(-{\displaystyle \frac{t_k}{\tau }}\right){\displaystyle \prod _0^{k-1}\exp \left[-\frac{w_l^2}{w_g^2}\exp \left(-\frac{2r^2}{w_g^2}\right){\mathrm{\Phi }}_m\right]} \\ \times \left\{R_{in}(r)\exp \left(-{\displaystyle \frac{2r^2}{w_p^2}}\right)\right.\exp \left({\displaystyle \frac{t_k}{\tau }}\right){\displaystyle {\int }_0^{t_k}{\displaystyle \prod _0^{k-1}\exp \left[\frac{w_l^2}{w_g^2}\exp \left(-\frac{2r^2}{w_g^2}\right){\mathrm{\Phi }}_m\right]}}dt \\ \left.+n(0,0)\exp \left(-{\displaystyle \frac{2r^2}{w_p^2}}\right)\right\}, \end{gathered}$$

(17)$$\begin{gathered} n_{s1}(r,t_k)=\exp \left(-{\displaystyle \frac{t_k}{{\tau }_s}}\right){{\displaystyle \prod _0^{k-1}\exp \left[-\frac{w_l^2}{w_s^2}\exp \left(-\frac{2r^2}{w_s^2}\right){\mathrm{\Phi }}_m\right]}}^{{\sigma }_g/\sigma } \\ \left.\times \left\{{\displaystyle \frac{n_{s0}}{{\tau }_s}}\exp \left({\displaystyle \frac{t_k}{\tau }}\right){{\displaystyle {\int }_0^{t_k}{\displaystyle \prod _0^{k-1}\exp \left[\frac{w_l^2}{w_s^2}\exp \left(-\frac{2r^2}{w_s^2}\right){\mathrm{\Phi }}_m\right]}}}^{-{\sigma }_g/\sigma }dt\right.+n_{s0}\right\}, \end{gathered}$$

(18)${\phi }_{id}(0,t_k)=\exp \left[-{\displaystyle \frac{L_{id}+\ln \left(\frac{1}{R_{id}}\right)}{t_{rid}}}{t}_k\right]{\displaystyle \prod _{m=0}^{k-1}\exp \left[\frac{1}{t_{rid}}2{\sigma }_{opo}\right.c{l}_{KTA}\frac{w_l^2}{w_k^2}}\left.\exp \left(-{\displaystyle \frac{2r^2}{w_k^2}}\right)G(t_m){\mathrm{\Phi }}_m\right],$

where $w_p$ represents the pump beam radius. To define the initial conditions:

(19)$n(r,0)=n(0,0)\exp (-{\displaystyle \frac{2r^2}{w_p^2}}),$

(20)$n_{s1}(r,0)=n_{s0},$

By numerically solving Equations (9) and (15)–(20), the resulting output pulse energies for both the idler and signal waves can be derived as follows:

(21)$E_{id}={\displaystyle \frac{\pi w_k^{2}ch{v}_{id}}{4}}\ln ({\displaystyle \frac{1}{R_{id}}}){\displaystyle {\int }_0^{\infty }{\varphi }_{id}(0,t)dt},$

(22)$E_s={\displaystyle \frac{\pi w_k^{2}ch{v}_s}{4}}{\displaystyle {\int }_0^{\infty }{\varphi }_s(0,t)dt},$

4.4. Numerical Simulation Results

In the numerical simulation, ${\tau }_p$ holds a significant role as it correlates with the ML pulse duration $\tau$. Given the fluctuation mechanism’s assumption that the ML pulse width $\tau$ remains constant [32], ${\tau }_p$ can be treated as a constant value throughout the simulation. The numerically simulated value of ${\tau }_p$ is basically in agreement with the experimental duration. It is noteworthy that in the numerical simulation, the pulse width of the ML pulse underneath the Q-switched envelope remained constant, consistent with the fluctuation mechanism’s theoretical explanation. However, in the experimental setup, the pulse width of the ML pulse underneath the Q-switched envelope marginally decreased with increasing pump power. This reduction in pulse width continued as the single ML pulse was generated. In the simulation, the pulse width of the single ML pulse was provided at the threshold pump power to verify the experimental results. Table 2 outlines the values of the other pertinent parameters employed in the numerical simulation. By using the parameters outlined in Table 1 and Table 2, we can ascertain ${\mathrm{\Phi }}_k$ with a specified initial value of ${\mathrm{\Phi }}_0$ via the numerical solution of Equations (6)–(20). Subsequently, the output pulse energies of the idler and signal waves can be determined using Equations (21) and (22), respectively. Since the average output power within a Q-switched envelope accounts for the summation of the output powers of all the ML pulses under the Q-switched envelope, the pulse width of the Q-switched envelope can be inferred from the shape of P(t). Given that the time interval between two neighboring ML pulses matches the cavity round-trip time, acquiring a single ML pulse beneath a Q-switched envelope necessitates that the pulse width of the Q-switched envelope is shorter than the cavity round-trip time.

The plotted curves in Figure 5 and Figure 6 depict the theoretically calculated data for the widths of the Q-switched envelopes and the pulse energies of the signal and idler waves concerning various pump powers corresponding to different repetition rates of the AOM.

Figure 5 specifically showcases the variations in the pulse widths of the signal and idler waves’ Q-switched envelopes in relation to pump powers for various values of $f_p$, represented by different curves. The figure reveals two distinct operational stages of the idler-resonant KTA IOPO driven by a dual-loss-modulated QML laser: the initial QML stage and the final sub-nanosecond single ML stage. During the QML stage, it is evident that the pulse widths of both the signal and idler waves’ Q-switched envelopes decrease as the pump power increases while decreasing $f_p$, indicating that lower repetition rates of the AOM lead to shorter pulse durations. At specific pump powers of 14.9 W for $f_p$ = 1 kHz, 16.5 W for $f_p$ = 2 kHz, 17.6 W for $f_p$ = 3 kHz, and 18.7 W for $f_p$ = 4 kHz, the pulse widths of the signal wave’s Q-switched envelopes became shorter than the cavity round-trip time, resulting in the generation of a signal wave’s single ML pulse per envelope. Concurrently, when reaching pump powers of 15.9 W for $f_p$ = 1 kHz, 17.5 W for $f_p$ = 2 kHz, 18.6 W for $f_p$ = 3 kHz, and 19.5 W for $f_p$ = 4 kHz, the idler wave’s single ML pulse per envelope was achieved. These theoretical calculations were largely consistent with the experimental findings above. However, a minor discrepancy between the experimental and simulation results was observed. Specifically, the experimental threshold powers for achieving the sub-nanosecond single ML pulses of the signal and idler waves were slightly lower than those values by the numerical simulation.

When $f_p$ = 1 kHz, the variations in the number of ML pulses for both the signal and idler waves within a Q-switched envelope at different pump powers are depicted in Figure 12. From Figure 12a–d, it is evident that the ML pulse count for both the signal and idler waves within a Q-switched envelope decreases with increasing pump power. Notably, when P_in = 16 W, as shown in Figure 12d, there is only a single ML pulse present for both the signal and idler waves beneath the Q-switched envelope. From the results shown in Figure 10, Figure 11 and Figure 12, it can be seen that the theoretical simulation results are consistent with the experimental results, which verifies the correctness of the theoretical simulation.

The simulated pulse energies and peak powers of the signal and idler waves’ Q-switched envelopes for different $f_p$ are depicted in Figure 6 and Figure 7 using curves, respectively. The trend shows that the pulse energies of both the signal and idler waves’ Q-switched envelopes exhibit an approximate linear increase in relation to the pump powers. However, it is notable that as $f_p$ increases, there is a decrease observed in the pulse energies and peak powers of both the signal and idler waves’ Q-switched envelopes. This suggests that a lower repetition rate tends to enhance the pulse energies and peak powers of the signal and idler waves’ QML pulses.

The performance of 2D nanomaterial-based intracavity OPOs driven by dual-loss-modulated QML lasers at 1 μm wavebands is summarized in Table 3. In comparison to the other 2D nanomaterial-based SAs, the idler wave’s pulse width of the idler-resonant intracavity KTA OPO with MoWS₂ SA is comparatively shorter, resulting in a relatively high peak power.

The 2D MoWS₂ SA offers a broad and tunable spectral window, making it highly versatile for various laser applications. In our study, the MoWS₂ SA demonstrates strong nonlinear optical absorption over a wide wavelength range. By tuning the phase-matching conditions in the intracavity KTA OPO, we can achieve efficient wavelength tunability. This flexibility enables the SA to operate effectively in both the signal and idler wavelengths, showcasing its adaptability for different laser systems. We observed that the MoWS₂ SA can function across a broad spectral window, from the near-infrared to mid-infrared region, with stable pulse generation. This wideband operation highlights its suitability for wavelength-tunable laser systems. The tunable response, in combination with its high damage threshold, makes the MoWS₂ SA an ideal candidate for high-power and tunable laser applications. However, stability is critical for practical laser applications, especially in high-power scenarios. Our experimental tests demonstrated that the MoWS₂ SA maintains consistent performance over extended periods of operation without degradation. The 2D nanomaterial’s robustness under both thermal and optical stress contributes to its long-term stability, even at high power levels. We conducted long-term operation tests and observed no significant changes in the material’s nonlinear properties or damage under high-intensity laser illumination.

5. Conclusions

In conclusion, the creation of layered MoWS₂ through liquid-phase exfoliation methods has showcased exceptional optical modulation properties, particularly for laser pulse generation within the 1 µm wavelength range. The experimental demonstrations confirm the efficiency of the IOPO driven by dual-loss-modulation technology employing AOM and MoWS₂ SA, highlighting its capability to generate high-peak-power sub-nanosecond near-infrared and mid-infrared single mode-locking pulses. The related coupled rate equations for the diode-pumped, idler-resonant KTA IOPO, driven by a dual-loss-modulated QML YVO₄/Nd:YVO₄ laser with AOM and MoWS₂ SA, have been successfully presented and simulated numerically. Remarkably, these numerical simulation results align fundamentally with the experimental observations. This approach opens new vistas for optoelectronic applications of MoWS₂ nanomaterials in the mid-infrared waveband.

Author Contributions

Conceptualization, S.Z. and H.Z.; methodology, C.H.; software, C.H.; validation, T.F., D.L. and H.Z.; formal analysis, H.C.; investigation, C.H.; resources, J.Z. and W.H.; data curation, T.F.; writing—original draft preparation, C.H.; writing—review and editing, S.Z.; visualization, C.H.; supervision, S.Z. and H.Z.; project administration, S.Z.; funding acquisition, S.Z. All authors have read and agreed to the published version of the manuscript.

Data Availability Statement

The data presented in this study are available in this article.

Conflicts of Interest

The authors declare no conflicts of interest. The funders had no role in the design of the study; in the collection, analyses, or interpretation of data; in the writing of the manuscript; or in the decision to publish the results.

Footnotes

Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to people or property resulting from any ideas, methods, instructions or products referred to in the content.

Figures and Tables

Figure 1. Characterization results of the structure and morphology: (a) XRD spectra, (b) Raman spectrum, (c) SEM and EDS mapping pattern, (d) TEM image, (e) high-resolution TEM image, (f) AFM image and height distribution.

Figure 2. (a) Absorption spectrum and (b) nonlinear transmittance curve of the MoWS2 SA (inset: the linear relation for low-power density).

Figure 3. Schematic diagram of the experimental setup.

Figure 4. The average output powers of the signal and idler waves versus pump powers for different [Forumla omitted. See PDF.].

Figure 5. The pulse widths of the Q-switched envelopes for the signal and idler waves versus pump powers for different [Forumla omitted. See PDF.]. Symbol: experimental data; curve: theoretical result.

Figure 6. The pulse energies of the signal and idler waves’ Q-switched pulses versus pump powers for different [Forumla omitted. See PDF.]. Symbol: experimental data; curve: theoretical result.

Figure 7. The peak powers of the signal and idler waves’ Q-switched pulses versus pump powers for different [Forumla omitted. See PDF.]. Symbol: experimental data; curve: theoretical result.

Figure 8. A representative output spectrum of the idler-resonant dual-loss-modulated QML KTA IOPO at an incident pump power of 19.4 W and an AOM modulation rate of 1 kHz.

Figure 9. (a) Extended temporal profile of the idler wave’s sub-nanosecond single ML pulse for [Forumla omitted. See PDF.] = 1 kHz and (b) oscilloscope trace of the idler wave’s single ML pulse train for [Forumla omitted. See PDF.] = 1 kHz.

Figure 10. The pulse shapes of the signal wave at various incident pump powers when the modulation frequency is 1 kHz: (a) 11.29 W, (b) 12.52 W, (c) 14.01 W, (d) 14.68 W.

Figure 11. The pulse shapes of the idler wave at different incident pump powers when the modulation frequency is 1 kHz: (a) 11.29 W, (b) 12.52 W, (c) 14.68 W, (d) 16.16 W.

Figure 12. The number of ML pulses within a Q-switched envelope for both the signal and idler waves varies with pump powers at [Forumla omitted. See PDF.] = 1 kHz.

Table 1

The key parameters for the saturable absorption characteristics of 2D MoWS₂ SA.

Parameters	Values	Parameters	Values
σg	6.98 × 10−19 cm2	lsa	10 nm
σe	3.4 × 10−19 cm2	ns 0	2.968 × 1023 cm−3
τs	714.1 µs

Table 2

Other parameters for theoretical solutions.

Parameters	Values	Parameters	Values	Parameters	Values
σ	2.5 × 10−18 cm2	α	3.8 cm−1	tao	14 ns
l	10 mm	λp	808 nm	δa	1
la	47 mm	λs	1535 nm	deff	−2.99 pm/V
Lc	1195 mm	λf	1064 nm	h	6.63 × 10−34 J·s
lopo	38 mm	λid	3467 nm	${\epsilon }_0$	8.85 × 10−12 F/m
lKTA	20 mm	n	1.96	Kc	5.1 W/mK
wp	200 μm	na	1.53	c	3.0 × 108 m/s
wl	187 μm	ns	1.385	Rs	0.007
wg	184 μm	nf	1.367	Rid	0.91
wa	206 μm	ni	1.4	L	0.1
ws	216 μm	τ	90 μs	Ls	0.05
wk	141 μm	τp	450 ps	Lid	0.01
wid	141 μm	fa	0.43

Table 3

A performance comparison of 2D nanomaterial-based intracavity OPOs driven by dual-loss-modulated QML lasers.

SA	GainMedium	Nonlinear Crystal	ResonantWave	OutputPower	PulseWidth	RepetitionRate	PulseEnergy	PeakPower	Refs.
SWCNT	YVO4/Nd:YVO4	KTP	Signalwave	Signal wave: 373 mW	Signal wave: 119 ps	2 kHz	Signal wave: 124 μJ	Signal wave: 1.04 MW	[35]
Sb2Te3	YVO4/Nd:YVO4	KTA	Idler wave	Signal wave: 353 mW;Idler wave: 173 mW	Signal wave: 545 ps;Idler wave: 936 ps	1 kHz	Signal wave: 353 μJ;Idler wave: 173 μJ	Signal wave: 648 kW;Idler wave: 185 kW	[36]
MoWS2	YVO4/Nd:YVO4	KTA	Idler wave	Signal wave: 318 mW;Idler wave: 169 mW	Signal wave: 720 ps;Idler wave: 830 ps	1 kHz	Signal wave: 318 μJ;Idler wave: 169 μJ	Signal wave: 441.6 kW;Idler wave: 203.6 kW	This work

References

1. Huber, G.; Kränkel, C.; Petermann, K. Solid-state lasers: Status and future. J. Opt. Soc. Am. B; 2010; 27, pp. B93-B105. [DOI: https://dx.doi.org/10.1364/JOSAB.27.000B93]

2. Kiefer, J.; Seeger, T.; Dreier, T.; Chen, W.; Stauffer, H.; Meier, W. Laser applications to chemical, security, and environmental analysis: Introduction to the feature issue. Appl. Opt.; 2019; 58, pp. LAC1-LAC3. [DOI: https://dx.doi.org/10.1364/AO.58.00LAC1]

3. Chen, T.-W.; Chang, K.-C.; Chen, J.-C.; Lin, J.-H.; Wei, M.-D. Role of modulation frequency in a hybrid Q-switched Nd:LuVO₄ laser with an acousto-optic modulator and a Cr⁴⁺:YAG saturable absorber. Appl. Opt.; 2014; 53, pp. 3459-3464. [DOI: https://dx.doi.org/10.1364/AO.53.003459]

4. Lin, J.-H.; Lin, K.-H.; Hsu, H.-H.; Hsieh, W.-F. Q-switched and mode-locked pulses generation in Nd:GdVO₄ laser with dual loss-modulation mechanism. Laser Phys. Lett.; 2008; 5, pp. 276-280. [DOI: https://dx.doi.org/10.1002/lapl.200710125]

5. Wang, J.; Liu, N.; Song, P.; Zhang, H. Dynamical modeling and experiment for an intra-cavity optical parametric oscillator pumped by a Q-switched self-mode-locking laser. Laser Phys.; 2016; 26, 115401. [DOI: https://dx.doi.org/10.1088/1054-660X/26/11/115401]

6. Qiao, J.; Zhao, S.; Yang, K.; Zhao, J.; Li, G.; Li, D.; Li, T.; Qiao, W.; Lu, J.; Wang, Y. et al. Doubly Q-Switched Laser With AOM-and SWCNT-SA-Driven KTP Intracavity OPO. IEEE Photonics Technol. Lett.; 2016; 28, pp. 2455-2458. [DOI: https://dx.doi.org/10.1109/LPT.2016.2600559]

7. Laporte, C.; Dherbecourt, J.B.; Melkonian, J.-M.; Raybaut, M.; Drag, C.; Godard, A. Pulse Compression in a Synchronously Pumped Optical Parametric Oscillator with a Graphene Saturable Absorber. Proceedings of the 2013 Conference on Lasers & Electro-Optics Europe & International Quantum Electronics Conference CLEO EUROPE/IQEC; Munich, Germany, 12–16 May 2013.

8. Wang, J.; Pang, J.; Liu, S.; Zhang, H.; Tang, W.; Xia, W. Experimental and dynamical study of a dual Q-switched intracavity OPO based on few-layer MoSe₂ SA. Opt. Express; 2019; 27, pp. 36474-36486. [DOI: https://dx.doi.org/10.1364/OE.27.036474]

9. Xie, L.M. Two-dimensional transition metal dichalcogenide alloys: Preparation, characterization and applications. Nanoscale; 2015; 7, pp. 18392-18401. [DOI: https://dx.doi.org/10.1039/C5NR05712D]

10. Komsa, H.-P.; Krasheninnikov, A.V. Two-Dimensional Transition Metal Dichalcogenide Alloys: Stability and Electronic Properties. J. Phys. Chem. Lett.; 2012; 3, pp. 3652-3656. [DOI: https://dx.doi.org/10.1021/jz301673x]

11. Kutana, A.; Penev, E.S.; Yakobson, B.I. Engineering electronic properties of layered transition-metal dichalcogenide compounds through alloying. Nanoscale; 2014; 6, pp. 5820-5825. [DOI: https://dx.doi.org/10.1039/C4NR00177J]

12. Xi, J.; Zhao, T.; Wang, D.; Shuai, Z. Tunable electronic properties of two-dimensional transition metal dichalcogenide alloys: A first-principles prediction. J. Phys. Chem. Lett.; 2014; 5, pp. 285-291. [DOI: https://dx.doi.org/10.1021/jz402375s] [PubMed: https://www.ncbi.nlm.nih.gov/pubmed/26270701]

13. Li, H.; Yu, K.; Tang, Z.; Zhu, Z. Experimental and first-principles investigation of MoWS₂ with high hydrogen evolution performance. ACS Appl. Mater. Interfaces; 2016; 8, pp. 29442-29451. [DOI: https://dx.doi.org/10.1021/acsami.6b09620] [PubMed: https://www.ncbi.nlm.nih.gov/pubmed/27754667]

14. Klee, V.; Preciado, E.; Barroso DNguyen, A.E.; Lee, C.; Erickson, K.J.; Triplett, M.; Davis, B.; Lu, I.-H.; Bobek, S.; McKinley, J. et al. Superlinear Composition-Dependent Photocurrent in CVD-Grown Monolayer MoS_2(1−x)Se_2x Alloy Devices. Nano Lett.; 2015; 15, pp. 2612-2619. [DOI: https://dx.doi.org/10.1021/acs.nanolett.5b00190] [PubMed: https://www.ncbi.nlm.nih.gov/pubmed/25723259]

15. Chen, Y.; Xi, J.; Dumcenco, D.O.; Liu, Z.; Suenaga, K.; Wang, D.; Shuai, Z.; Huang, Y.-S.; Xie, L. Tunable Band Gap Photoluminescence from Atomically Thin Transition-Metal Dichalcogenide Alloys. ACS Nano; 2013; 7, pp. 4610-4616. [DOI: https://dx.doi.org/10.1021/nn401420h]

16. Yan, Z.; Li, T.; Zhao, J.; Yang, K.; Li, D.; Li, G.; Zhang, S.; Zhao, S. Generation of microsecond pulses at 1645 nm with MoWS₂ alloy. Opt. Mater.; 2018; 84, pp. 371-374. [DOI: https://dx.doi.org/10.1016/j.optmat.2018.07.042]

17. Ahmad, H.; Aidit, S.N.; Mohanraj, J.; Sivabalan, S.; Thambiratnam, K.; Ooi, S.I.; Tiu, Z.C. Mixed Transition Metal Dichalcogenide as Saturable Absorber in Ytterbium, Praseodymium, and Erbium Fiber Laser. IEEE J. Sel. Top. Quantum Electron.; 2018; 54, 1600409. [DOI: https://dx.doi.org/10.1109/JQE.2018.2822181]

18. Ahmad, H.; Sharbirin, A.S.; Ismail, M.F. Molybdenum tungsten disulphide (MoWS₂) as a saturable absorber for a passively Q-switched thulium/holmium-codoped fibre laser. J. Mod. Opt.; 2019; 66, pp. 1163-1171. [DOI: https://dx.doi.org/10.1080/09500340.2019.1609612]

19. Niu, Z.; Feng, T.; Li, T.; Yang, K.; Zhao, J.; Li, G.; Li, D.; Zhao, S.; Qiao, W.; Chu, H. et al. Doubly Q-switched mode-locked Tm:YAP laser at 2 μm with ternary MoWS₂ alloy and EOM. Opt. Commun.; 2022; 520, 128544. [DOI: https://dx.doi.org/10.1016/j.optcom.2022.128544]

20. Coleman, J.N.; Lotya, M.; O’Neill, A.; Bergin, S.D.; King, P.J.; Khan, U.; Young, K.; Gaucher, A.; De, S.; Smith, R.J. et al. Two-Dimensional Nanosheets Produced by Liquid Exfoliation of Layered Materials. Science; 2011; 331, pp. 568-571. [DOI: https://dx.doi.org/10.1126/science.1194975]

21. Dumcenco, D.O.; Chen, K.Y.; Wang, Y.P.; Huang, Y.S.; Tiong, K.K. Raman study of 2H-Mo_1−xW_xS₂ layered mixed crystals. J. Alloys Compd.; 2010; 506, pp. 940-943. [DOI: https://dx.doi.org/10.1016/j.jallcom.2010.07.120]

22. Ren, K.; Yu, G.; Zhang, Z.; Wu, W.; Tian, P.; Chhattal, M.; Gong, Z.; Li, Y.; Zhang, J. Self-organized transfer film-induced ultralow friction of Graphene/MoWS₄ heterostructure nanocomposite. Appl. Surf. Sci.; 2022; 572, 151443. [DOI: https://dx.doi.org/10.1016/j.apsusc.2021.151443]

23. Miremadi, B.K.; Morrison, S.R. Preparation of alternating MoS₂ and WS₂ single layers to form a new MoWS₄ structure. J. Appl. Phys.; 1990; 67, pp. 1515-1520. [DOI: https://dx.doi.org/10.1063/1.345661]

24. Wang, X.; Feng, H.; Wu, Y.; Jiao, L. Controlled Synthesis of Highly Crystalline MoS₂ Flakes by Chemical Vapor Deposition. J. Am. Chem. Soc.; 2013; 135, pp. 5304-5307. [DOI: https://dx.doi.org/10.1021/ja4013485] [PubMed: https://www.ncbi.nlm.nih.gov/pubmed/23489053]

25. Nguyen, D.A.; Le, T.S.; Park, D.Y.; Suh, D.; Jeong, M.S. Synthesis of MoWS₂ on flexible carbon-based electrodes for high-performance hydrogen evolution reaction. ACS Appl. Mater. Interfaces; 2019; 11, pp. 37550-37558. [DOI: https://dx.doi.org/10.1021/acsami.9b10383] [PubMed: https://www.ncbi.nlm.nih.gov/pubmed/31553157]

26. Kong, L.; Chu, H.; Xu, M.; Xu, S.; Pan, Z.; Zhao, S.; Li, D. Oxygen vacancy engineering of MOF-derived ZnO/Co₃O₄ nanocomposites for high harmonic mode-locking operation. J. Mater. Chem. C; 2022; 10, pp. 16564-16572. [DOI: https://dx.doi.org/10.1039/D2TC03503K]

27. Bélanger, P.A. Beam propagation and the ABCD ray matrices. Opt. Lett.; 1991; 16, pp. 196-198. [DOI: https://dx.doi.org/10.1364/OL.16.000196]

28. Stratan, A.; Rusen, L.; Dabu, R.; Fenic, C.; Blanaru, C. Picosecond laser system based on microchip oscillator. J. Optoelectron. Adv. Mater.; 2008; 10, pp. 3022-3028.

29. Weller, D. Relating wideband DSO rise time to bandwidth: Lose the 0.35!. EDN; 2002; 47, pp. 89-94.

30. Chen, Y.F.; Tsai, S.W. Simultaneous Q-switching and mode-locking in a diode-pumped Nd:YVO₄-Cr⁴⁺:YAG laser. IEEE J. Quantum Electron.; 2001; 37, pp. 580-586. [DOI: https://dx.doi.org/10.1109/3.914408]

31. Chen, Y.F.; Lee, J.L.; Hsieh, H.D.; Tsai, S.W. Analysis of passively Q-switched lasers with simultaneous mode-locking. IEEE J. Quantum Electron.; 2002; 38, pp. 312-317. [DOI: https://dx.doi.org/10.1109/3.985573]

32. Zhao, S.; Li, G.; Li, D.; Yang, K.; Li, Y.; Li, M.; Li, T.; Zhang, G.; Cheng, K. Numerical simulation of dual-loss-modulated Q-switched and mode-locked laser with an acousto-optic and Cr⁴⁺:YAG saturable absorber. Appl. Opt.; 2010; 49, pp. 1802-1808. [DOI: https://dx.doi.org/10.1364/AO.49.001802] [PubMed: https://www.ncbi.nlm.nih.gov/pubmed/20357862]

33. Bai, F.; Wang, Q.; Liu, Z.; Zhang, X.; Wan, X.; Lan, W.; Jin, G.; Tao, X.; Sun, Y. Theoretical and experimental studies on output characteristics of an intracavity KTA OPO. Opt. Express; 2012; 20, pp. 807-815. [DOI: https://dx.doi.org/10.1364/OE.20.000807] [PubMed: https://www.ncbi.nlm.nih.gov/pubmed/22274426]

34. Debuisschert, T.; Raffy, J.; Pocholle, J.P.; Papuchon, M. Intracavity optical parametric oscillator: Study of the dynamics in pulsed regime. J. Opt. Soc. Am. B; 1996; 13, pp. 1569-1587. [DOI: https://dx.doi.org/10.1364/JOSAB.13.001569]

35. Qiao, J.; Zhao, S.; Yang, K.; Zhao, J.; Li, G.; Li, D.; Li, T.; Qiao, W.; Lu, J.; Wang, Y. et al. High-peak-power sub-nanosecond intracavity KTiOPO₄ optical parametric oscillator pumped by a dual-loss modulated laser with acousto-optic modulator and single-walled carbon nanotube. Appl. Phys. Exp.; 2016; 9, 082701. [DOI: https://dx.doi.org/10.7567/APEX.9.082701]

36. Han, C.; Chu, H.; Feng, T.; Zhao, S.; Li, D.; Feng, C.; Zhao, J.; Huang, W. High-power idler-resonant intracavity KTA OPO driven by a dual-loss-modulated Q-switched mode-locked laser with AOM and Sb₂Te₃ nanosheets. Opt. Express; 2024; 32, pp. 29868-29886. [DOI: https://dx.doi.org/10.1364/OE.533443]