Studies on the Photoinduced Interaction between Zn(II) Porphyrin and Colloidal TiO2

Abstract

The interaction of Zn(II) porphyrin (ZnPP) with colloidal TiO2 was studied by absorption and fluorescence spectroscopy. The fluorescence emission of ZnPP was quenched by colloidal TiO2 upon excitation of its absorption band. The quenching rate constant (kq ) is 1.24×[superscript]1011[/superscript] M-1 s-1. These data indicate that there is an interaction between ZnPP and colloidal TiO2 nanoparticle surface. The quenching mechanism is discussed on the basis of the quenching rate constant as well as the reduction potential of the colloidal TiO2. And the mechanism of electron transfer has been confirmed by the calculation of free energy change (Δ[subscript]Get[/subscript] ) by applying Rehm-Weller equation as well as energy level diagram.

Heyong Huang 1, 2 and Jiahong Zhou 1, 2 and Yan Zhou 2 and Yanhuai Zhou 3 and Yuying Feng 1, 2

Recommended by Detlef W. Bahnemann

1, Key Lab of Biofunctional Materials of Jiangsu Province, Analysis and Testing Center, Nanjing Normal University, Nanjing 210097, China
2, Department of Chemistry and Environmental Science, Nanjing Normal University, Nanjing 210097, China
3, Department of Physical Science and Technology, Nanjing Normal University, Nanjing 210097, China

Received 5 August 2010; Revised 18 October 2010; Accepted 22 October 2010

1. Introduction

Wide-band gap semiconductor particles such as TiO₂ have been widely used for different applications in photocatalysis and the environment [1, 2].Over the past decades, considerable interest has been shown in the modification of TiO₂ semiconductors by organic dyes to extend the photoresponse to visible light owing to their potential application in solar energy conversion [3-5]. Dye sensitization is considered to be an efficient method to modify the photo response properties of TiO₂ particles. The dyes used are erythrosine B [6], rose Bengal [7], metal porphyrin [8-10], and so forth.

Porphyrins, (including metal-free porphyrins, metalloporphyrins and supramolecular porphyrins) [11] are recognized to be the most promising sensitizers [12]. The chemistry of porphyrin derivatives has played an important role especially during the past decade in particular branches of new materials science, and many researchers have undertaken projects on the synthesis of variously substituted compounds to obtain new functional materials [13-15]. Metalloporphyrin may be an appropriate candidate because of its high absorption coefficient within the solar spectrum and its good chemical stability in comparison to that of other dyes. They are highly effective photocatalysts due to their very strong absorption in the 400 nm-450 nm region (Soret band) and in the 500 nm-700 nm region (Q-bands) and, in fact, the presence of p-electrons affords the condition for electron transfer during the photoreaction.

In the present work we have investigated the electron transfer from excited ZnPP (see Scheme 1) to the conduction band of TiO₂ colloid by using absorption and fluorescence spectroscopy.

Scheme 1: Structure of ZnPP.

[figure omitted; refer to PDF]

2. Materials and Methods

2.1. Materials

Zn(II) porphyrin and tetrabutyl titanate were purchased from Aldrich. The doubly distilled water was used for preparing the solutions. All measurements were performed at room temperature (28°C).

2.2. Preparation of Colloidal TiO₂

The colloidal TiO₂ suspension was prepared by the hydrolysis of tetrabutyl titanate (C₁₆ H₃₆ O₄ Ti). Typically, tetrabutyl titanate (C₁₆ H₃₆ O₄ Ti) in 2-propanol was injected by using syringe into water with constant stirring under nitrogen atmosphere (8 h) it giving 1 × 10^-2 M titania stock solution. No stabilizing agents were used during the hydrolysis process. The colloidal suspensions of TiO₂ prepared by this method were stable for 3-5 days. Fresh colloidal TiO₂ dispersed in water was prepared before each set of experiments. No attempts were made to exclude the traces of 2-propanol present in the colloidal TiO₂ suspension and it was confirmed separately that the presence of 2-propanol did not affect the photochemical measurements as earlier reported [16].

2.3. Instrumentation

The steady-state fluorescence quenching measurements were carried out with Perkin Element LS-50B spectrofluorimeter. The excitation wavelength of ZnPP was 420 nm and the emission was at 589 nm. The excitation and emission slit widths (each 5 nm) and scan rate (600 nm/min) were maintained constant for all the experiments. The samples were carefully degassed using pure nitrogen gas for 15 min. Quartz cells (4 cm × 1 cm × 1 cm) with high vacuum Teflon stopcocks were used for degassing. Absorption spectral measurements were recorded using Varian Cary 5000 NIR-UV-Vis spectrophotometer.

3. Results and Discussion

3.1. UV-Vis and Fluorescence Spectra Studies

The absorption and emission spectra of ZnPP (Figure 1) were recorded in the absence and in presence of colloidal TiO₂ (Figures 2 and 3). From Figure 2 we can see in the region of 300 nm-500 nm, ZnPP has one characteristic absorption band with absorption maxima at 420 nm. After addition of different concentration of TiO₂ to ZnPP solution, the shape and band maxima of absorption spectra of ZnPP remain unchanged, but the intensities decreased greatly. The fluorescence spectra of ZnPP with varying concentrations of TiO₂ are shown in Figure 3; it is clear that the fluorescence spectra of ZnPP remain unchanged, and no other new emission band of the ZnPP is noticed. However, TiO₂ can quench the fluorescence of ZnPP effectively.

Figure 1: Absorption (A) and emission (B) spectrum of ZnPP.

[figure omitted; refer to PDF]

Figure 2: Absorption spectrum of ZnPP in the presence of colloidal TiO₂ in the concentration range of (0-5) × 10^-4 M in water.

[figure omitted; refer to PDF]

Figure 3: Steady state fluorescence quenching of ZnPP (2 × 10^-6 M) with colloidal TiO₂ in the concentration range of (0-5) × 10^-4 M in water.

[figure omitted; refer to PDF]

The above observations suggest that the ZnPP-TiO₂ interaction does not change the absorption and fluorescence spectral properties and the formation of any emissive exciplex may be ruled out.

The Stern-Volmer constant (_Ksv ) and the quenching rate constant (_kq ) for the fluorescence quenching of ZnPP were determined from Stern-Volmer plots using emission intensity data [figure omitted; refer to PDF] where [figure omitted; refer to PDF] where _I0 and I correspond to the intensities of the sensitizer in the absence and presence of the quencher, respectively, [Q ] the concentration of the quencher and _τ0 the emission lifetime of sensitizer. The Stern-Volmer plot in the quenching of ZnPP is linear with a correlation coefficient (^R2 ) of greater than 0.9966 indicating the dynamic nature of quenching process and absence of static quenching (Figure 4). From the slope of the above plot, the _Ksv values obtained are 4.48 × 10⁴ M^-1 , and using (2), namely, _Ksv =_kq τ , the _kq value calculated is found to be 1.24 × 10¹¹ M^-1 s^-1 .

Figure 4: Stern-Volmer plot for the fluorescence quenching of ZnPP with various concentrations of TiO₂ (0-5) × 10^-4 M in water.

[figure omitted; refer to PDF]

The decrease in fluorescence emission may be attributed to the various possibilities such as energy transfer, electron transfer, or ground state complex formation between the ZnPP and colloidal TiO₂ .

As shown in Scheme 2, the band gap energy of TiO₂ (3.2 eV) is greater than the excited state energy (2.11 eV) of ZnPP and there is no overlap between the fluorescence emission spectrum of ZnPP with the absorption spectrum of colloidal TiO₂ (Figure 5), so the above two inferences excluded the possibility of energy transfer from ZnPP to colloidal TiO₂ . From the above discussion, we confirmed that the fluorescence quenching shown in Figure 3 should not be caused by energy transfer.

Scheme 2: Energy level diagram for ZnPP and TiO_2.

[figure omitted; refer to PDF]

Figure 5: Absorption spectrum of TiO₂ (A) and emission spectrum of ZnPP (B).

[figure omitted; refer to PDF]

The possibility of surface complex formation between ZnPP and colloidal TiO₂ is the reason for quenching of ZnPP by colloidal TiO₂ .While increasing the concentration of colloidal TiO₂ , some of the ZnPP molecules were adsorbed on the surface of TiO₂ , so the number of molecules available for the fluorescence is reduced, which is the reason for decrease in fluorescence intensity.

The ability of the excited state ZnPP to inject its electrons into the conduction band of TiO₂ is determined by energy difference between the conduction band of TiO₂ and oxidation potential of excited state ZnPP. According to equation _{E^s* /^s+} =_Es/^s+ -_Es , the oxidation potential of excited state ZnPP is -1.24 eV versus SCE, where _Es/^s+ is the oxidation potential of ZnPP, (0.87 eV) versus SCE [17] and _Es is the excited state energy of ZnPP, 2.11 eV excited state energy of the ZnPP calculated from the fluorescence maximum based on the reported method [18]. The conduction band potential of TiO₂ is -0.1 eV versus SCE [19]. Scheme 3 suggested that electron transfer from excited state ZnPP to the conduction band of TiO₂ is energetically favorable.

Scheme 3: Schematic energy level diagram showing electron transfer process.

[figure omitted; refer to PDF]

Therefore, we conclude that the fluorescence quenching shown in Figure 3 is caused by electron transfer.

3.2. Calculation of Free Energy Changes (_ΔGet ) for the Electron Transfer Reactions

The nature of the electron transfer pathway (i.e., oxidative or reductive quenching) can be understood by examining the free energy of the corresponding reactions. Thermodynamics of electron transfer from the sensitizer to the quencher can be calculated by the well-known Rehm-Weller equation [20] [figure omitted; refer to PDF] where _{^E(ox) 1/2} is the oxidation potential of the donor, _{^E(red) 1/2} the reduction potential of the acceptor, _ES the singlet state energy of the sensitizer, and C is the coulombic term. Since one of the species is neutral and the solvent used is polar in nature, the coulombic term in the above expression is neglected [21]. The oxidation potential, excited singlet state energy (_ES ) and the calculated Δ_Get value for the ZnPP are shown in Table 1. The conduction band potential of TiO₂ is -0.1 V versus SCE [22]. By using Rehm-Weller equation negative value of Δ_Get was obtained. The absence of any overlap between the emission spectra of the ZnPP and the absorption spectrum of TiO₂ (Figure 5) and the well established electron accepting nature of ^ecb- of TiO₂ in presence of excited electron donors, namely, the dyes [23] coupled with the above observation support that the quenching mechanism in this work involves electron transfer (i.e., electron transfer from excited ZnPP to TiO₂ ) and hence there is no energy transfer.

Table 1: Photophysical properties of ZnPP.

S. no	Parameters	ZnPP
1	Eox versus SCE (eV)	0.87
2	ES (eV)	2.05
3	ΔGet (eV)	-1.08

3.3. Schematic Diagram Describing the Electron Transfer Quenching Process

Upon excitation of ZnPP, it goes to excited state, and an electron transfer from excited ZnPP to conduction band of TiO₂ occurs. [figure omitted; refer to PDF]

4. Conclusions

Based on the above results, the electron transfer mechanism was proposed for the fluorescence quenching of ZnPP by TiO₂ . ZnPP serves as electron donor and TiO₂ as electron acceptor. Quenching follows static mechanism through ground complex formation which is confirmed by the curvature of Stern-Volmer plot.

Acknowledgments

This work was supported by the Natural Science Foundation of China (Grant no. 20603018) and the Science Foundation of Jiangsu (Grant no. BM2007132), China. The authors gratefully acknowledge the anonymous reviewers whose comments helped to improve this paper.

References

[1] M. R. Hoffmann, S. T. Martin, W. Choi, D. W. Bahnemann, "Environmental applications of semiconductor photocatalysis," Chemical Reviews , vol. 95, no. 1, pp. 69-78, 1995.

[2] M. Muruganandham, M. Swaminathan, "Photocatalytic decolourisation and degradation of Reactive Orange 4 by Ti_O2 -UV process," Dyes and Pigments , vol. 68, no. 2-3, pp. 133-141, 2006.

[3] J. He, F. Chen, J. Zhao, H. Hidaka, "Adsorption model of ethyl ester of fluorescein on colloidal Ti_O2 and the mechanism of the interfacial electron transfer," Colloids and Surfaces A , vol. 142, no. 1, pp. 49-57, 1998.

[4] A. Kathiravan, R. Renganathan, "An investigation on electron transfer quenching of zinc(II) meso-tetraphenylporphyrin (ZnTPP) by colloidal Ti_O2 ," Spectrochimica Acta A , vol. 71, no. 3, pp. 1106-1111, 2008.

[5] A. Kathiravan, V. Anbazhagan, M. Asha Jhonsi, R. Renganathan, "Fluorescence quenching of meso-tetrakis (4-sulfonatophenyl) porphyrin by colloidal Ti_O2 ," Spectrochimica Acta A , vol. 70, no. 3, pp. 615-623, 2008.

[6] P. V. Kamat, M. A. Fox, "Photosensitization of Ti_O2 colloids by Erythrosin B in acetonitrile," Chemical Physics Letters , vol. 102, no. 4, pp. 379-390, 1983.

[7] H. Ross, J. Bendig, S. Hecht, "Sensitized photocatalytical oxidation of terbutylazine," Solar Energy Materials and Solar Cells , vol. 33, no. 4, pp. 475-483, 1994.

[8] G. Mele, G. Ciccarella, G. Vasapollo, E. García-López, L. Palmisano, M. Schiavello, "Photocatalytic degradation of 4-nitrophenol in aqueous suspension by using polycrystalline Ti_O2 samples impregnated with Cu(II)-phthalocyanine," Applied Catalysis B , vol. 38, no. 4, pp. 309-311, 2002., [email protected]; [email protected]

[9] G. Mele, R. Del Sole, G. Vasapollo, E. García-López, L. Palmisano, M. Schiavello, "Photocatalytic degradation of 4-nitrophenol in aqueous suspension by using polycrystalline Ti_O2 impregnated with functionalized Cu(II) -porphyrin or Cu(II)-phthalocyanine," Journal of Catalysis , vol. 217, no. 2, pp. 334-346, 2003., [email protected]

[10] G. Mele, R. Del Sole, G. Vasapollo, "Polycrystalline Ti_O2 impregnated with cardanol-based porphyrins for the photocatalytic degradation of 4-nitrophenol," Green Chemistry , vol. 6, no. 12, pp. 604-616, 2004.

[11] S. Cho, W.-S. Li, M.-C. Yoon, T. K. Ahn, D.-L. Jiang, J. Kim, T. Aida, D. Kim, "Relationship between incoherent excitation energy migration processes and molecular structures in zinc(II) porphyrin dendrimers," Chemistry , vol. 12, no. 29, pp. 7576-7583, 2006.

[12] M. Unno, T. Matsui, M. Ikeda-Saito, "Structure and catalytic mechanism of heme oxygenase," Natural Product Reports , vol. 24, no. 3, pp. 553-558, 2007., [email protected]

[13] R. Harada, Y. Matsuda, H. Okawa, T. Kojima, "A porphyrin nanotube: size-selective inclusion of tetranuclear molybdenum-oxo clusters," Angewandte Chemie , vol. 43, no. 14, pp. 1825-1831, 2004.

[14] T. S. Balaban, "Tailoring porphyrins and chlorins for self-assembly in biomimetic artificial antenna systems," Accounts of Chemical Research , vol. 38, no. 8, pp. 612-619, 2005., [email protected]

[15] Y. Cho, W. Choi, C.-H. Lee, T. Hyeon, H.-I. Lee, "Visible light-induced degradation of carbon tetrachloride on dye-sensitized Ti_O2 ," Environmental Science and Technology , vol. 35, no. 5, pp. 966-973, 2001.

[16] P. V. Kamat, J.-P. Chauvet, R. W. Fessenden, "Photoelectrochemistry in particulate systems. 4. Photosensitization of a Ti_O2 semiconductor with a chlorophyll analogue," Journal of Physical Chemistry , vol. 90, no. 7, pp. 1389-1395, 1986.

[17] K. Hasegawa, T. Noguchi, "Density functional theory calculations on the dielectric constant dependence of the oxidation potential of chlorophyll: implication for the high potential of P680 in photosystem II," Biochemistry , vol. 44, no. 24, pp. 8865-8872, 2005.

[18] E. J. Shin, D. Kim, "Substituent effect on the fluorescence quenching of various tetraphenylporphyrins by ruthenium tris(2,^{2[variant prime]} -bipyridine) complex," Journal of Photochemistry and Photobiology A , vol. 152, no. 1-3, pp. 25-31, 2002., [email protected]

[19] S. L. Murov, I. Carmichael, G. L. Hug Handbook of Photochemistry , Marcel-Dekker, New York, NY, USA, 1993., 2nd.

[20] D. Rehm, A. Weller, "Kinetics of fluorescence quenching by electron and hydrogen-atom transfer," Israel Journal of Chemistry , vol. 8, pp. 259-265, 1970.

[21] S. Parret, F. Morlet-Savary, J. P. Fouassier, P. Ramamurthy, "Spin-orbit-coupling-induced triplet formation of triphenylpyrylium ion: a flash photolysis study," Journal of Photochemistry and Photobiology A , vol. 83, no. 3, pp. 205-312, 1994.

[22] S. L. Murov, I. Carmichael, G.L. Hug Handbook of Photochemistry , Marcel-Dekker, New York, NY, USA, 1993., 2nd.

[23] Q. Dai, J. Rabani, "Photosensitization of nanocrystalline Ti_O2 films by anthocyanin dyes," Journal of Photochemistry and Photobiology A , vol. 148, no. 1-3, pp. 17-23, 2002.