Bright solid-state sources of indistinguishable single photons

Abstract

Bright sources of indistinguishable single photons are strongly needed for the scalability of quantum information processing. Semiconductor quantum dots are promising systems to build such sources. Several works demonstrated emission of indistinguishable photons while others proposed various approaches to efficiently collect them. Here we combine both properties and report on the fabrication of ultrabright sources of indistinguishable single photons, thanks to deterministic positioning of single quantum dots in well-designed pillar cavities. Brightness as high as 0.79±0.08 collected photon per pulse is demonstrated. The indistinguishability of the photons is investigated as a function of the source brightness and the excitation conditions. We show that a two-laser excitation scheme allows reducing the fluctuations of the quantum dot electrostatic environment under high pumping conditions. With this method, we obtain 82±10% indistinguishability for a brightness as large as 0.65±0.06 collected photon per pulse.

ARTICLE

Received 17 Aug 2012 | Accepted 2 Jan 2013 | Published 5 Feb 2013

O. Gazzano1, S. Michaelis de Vasconcellos1, C. Arnold1, A. Nowak1, E. Galopin1, I. Sagnes1, L. Lanco1,2,A. Lematre1 & P. Senellart1

Bright sources of indistinguishable single photons are strongly needed for the scalability of quantum information processing. Semiconductor quantum dots are promising systems to build such sources. Several works demonstrated emission of indistinguishable photons while others proposed various approaches to efciently collect them. Here we combine both properties and report on the fabrication of ultrabright sources of indistinguishable single photons, thanks to deterministic positioning of single quantum dots in well-designed pillar cavities. Brightness as high as 0.790.08 collected photon per pulse is demonstrated. The indistinguishability of the photons is investigated as a function of the source brightness and the excitation conditions. We show that a two-laser excitation scheme allows reducing the uctuations of the quantum dot electrostatic environment under high pumping conditions. With this method, we obtain 8210% indistinguishability for a brightness as large as0.650.06 collected photon per pulse.

DOI: 10.1038/ncomms2434

Bright solid-state sources of indistinguishable single photons

1 Laboratoire de Photonique et de Nanostructures, CNRS, UPR20, Route de Nozay, Marcoussis 91460, France. 2 Universit Paris Diderot, Dpartement de Physique, 4 rue Elsa Morante, 75013 Paris, France. Correspondence and requests for materials should be addressed to P.S. (email: mailto:[email protected]

Web End =pascale.senellart@ mailto:[email protected]

Web End =lpn.cnrs.fr ).

NATURE COMMUNICATIONS | 4:1425 | DOI: 10.1038/ncomms2434 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications 1

& 2013 Macmillan Publishers Limited. All rights reserved.

ARTICLE NATURE COMMUNICATIONS | DOI: 10.1038/ncomms2434

The quantum interference1 of two indistinguishable single photons is an important resource for long distance quantum communication and linear quantum

computing25. Recent years have seen important progress in the development of bright single-photon sources in solid-state systems using semiconductor self-assembled quantum dots (QDs)6 inserted in photonic structures710. QDs conne carriers in the three directions of space and present discrete energy states. When a laser pulse optically creates several electron-hole pairs in a QD, the system goes back to its ground state by emitting a cascade of photons. Thanks to the strong Coulomb interaction, only a single photon is emitted for a given emission energy11. This property has been exploited to generate single photons6, as well as single entangled photon pairs12,13. However, because only a few per cent of the emitted photons can be collected for QDs in bulk semiconductors, control of the QD spontaneous emission is needed to obtain bright quantum light sources. One can for instance insert the QD in a cavity to increase the local density of electromagnetic modes and accelerate its spontaneous emission into a given optical mode14,7,8,10. Another possibility is to use subwavelength waveguides to inhibit the emission in most directions of space9,15. State of the art extraction efciencies around 40% in 0.4 numerical aperture have been reported with both geometries8,9,10. In nanowires, this extraction efciency has been shown to reach 719% in a numerical aperture of 0.75 (ref. 9). Several works have also shown that single photons and entangled photon pairs can be made indistinguishable1618. Shortening of the QD lifetime has been used to minimize the inuence of dephasing processes and increase visibility19,20. However, combining high brightness and high indistinguishability is not straightforward. Indeed, to obtain high source brightness, a strong optical excitation of the quantum

system is needed. Thus, many carriers are created in the QD environment, leading to dephasing, which is expected to reduce indistinguishability. In this article, we report on highly indistinguishable single-photon sources with unprecedented brightness obtained by deterministic21 coupling of InGaAs QDs in pillars cavities. High indistinguishability is combined with high brightness thanks to a two colour excitation scheme.

ResultsExtracting single photons with pillar microcavities. When a QD is coupled to a cavity mode (Fig. 1a), its spontaneous emission into the cavity mode is accelerated by the Purcell factor FP (ref. 22). The fraction of photons emitted into the cavity mode is then given by b FP/(FP 1) (Fig. 1b). The brightness of a

source, dened by the number of collected photons in the rst lens per excitation pulse, is given by the product bZqQD where Z is the mode coupling to the external optical eld and qQD the

quantum efciency of the QD emission line. Pillar cavities are obtained by etching a planar cavity made of two distributed Bragg reectors around a k microcavity14. We rst note that absorption or scattering in the mirrors are negligible in the GaAs/AlAs system under consideration. Indeed, planar quality factors of a few 105 have been demonstrated using similar mirrors, only with a larger number of Bragg pairs23. To collect most photons from the top of the pillar, we use highly asymmetric cavities with a bottom mirror transmission more than three orders of magnitude smaller than the top mirror transmission. This strong unbalance in the mirror transmission ensures that less than 0.1% of photons escape through the bottom mirror24. However, losses can still arise from the sidewall roughness when reducing the pillar diameter. As a result, we expect the coupling to the external eld

a

b

Weak coupling

Microscope objective0.4 NA Collected photons:

Q

Q0

Cavity

Quantum dot

Electron

Hole

FP FP + 1

Single photon

Sidewall losses:

DBR 16 pairs

DBR 36 pairs

1

Q Q0

c

QD Cavity

Emission into other modes:

1.0

1

0.8

FP + 1

Extraction efficiency

0.6

0.4

0.2

0.0

4

2 Diameter (m)

Figure 1 | Extracting single photons using Purcell effect in micropillar cavities (a) A semiconductor QD is inserted in a microcavity. (b) In micropillars, a fraction FP/(FP 1) of the photons is emitted into the cavity mode. Owing to losses at the sidewall roughness, only a fraction Q/Q0 of these photons is

collected in the rst lens. (c) Fit of the experimentally measured Q/Q0 (black dashed line), calculated FP/(FP 1) (red dotted line) and the maximum

extraction efciency FP/(FP 1) Q/Q0 (solid green line) as a function of micropillar diameters.

2 NATURE COMMUNICATIONS | 4:1425 | DOI: 10.1038/ncomms2434 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications

& 2013 Macmillan Publishers Limited. All rights reserved.

NATURE COMMUNICATIONS | DOI: 10.1038/ncomms2434 ARTICLE

to be given by Z Q/Q0, where Q and Q0 are the quality factors of

the pillar mode and the planar cavity, respectively25.

Figure 1c shows a t to typical experimentally measured Q/Q0 for our etching conditions for a planar quality factor of Q0 3,000 (Methods). Q/Q0 increases when increasing the

pillar diameter and saturates close to 1 for a diameter around to 2 mm. Using this dependence for Z and knowing the optical mode volume as a function of diameter, we can also predict the variation of b. Small diameters yield large Purcell factors and b, whereas large diameters lead to negligible losses due to sidewall roughness. Figure 1c shows that extraction efciencies given by the product Zb can be larger than 70% for diameters between 2 and 3 mm. However, to obtain such high brightness, the QD should be centred in the pillar and spectrally resonant with the cavity mode. Finally, InAs/GaAs self-assembled QDs have large overall quantum efciencies (larger than 97%, see ref. 26). However, they have a non-negligible probability to be either in neutral, positively or a negatively charged exciton state under non-resonant optical pumping27. These charge state uctuations would, therefore, reduce qQD and the source efciency accordingly. As a result, QDs with a well-dened charged state should be selected. Obviously, gathering all these conditions is very demanding considering that QDs have random spectral and spatial positions. The absence of a deterministic technology to control the coupling between the QD and the cavity probably explains why such high brightnesses were not reported up to now.

Bright single-photon sources. Here we use the in situ lithography technique presented in ref. 21 to dene pillar cavities centred on single selected QDs within 50 nm (Methods). The sources are fabricated from a planar cavity presenting a quality factor of Q0E3,000. As the mode energy depends on the pillar diameter, we selected QDs presenting the emission energies of pillar cavity modes with diameters between 2.5 and 3.5 mm.

Finally, our technique provides the unique possibility to preselect QDs for which the emission of the neutral exciton emission is more than 10 times larger than the emission of both charged excitons. This ensures that qQD 40.9.

The devices are characterized through micro-photo-luminescence (PL) measurements at cryogenic temperatures. The sample is excited by a picosecond 82 MHz pulsed laser beam focused onto a 2-mm spot. The PL signal collected by the same objective is split in two paths and sent to spectrometers and detected with a liquid nitrogen cooled charge coupled device (CCD) or single-photon avalanche diodes (SPAD). The sample temperature is used to nely tune the spectral resonance between the cavity mode and the QD emission line21. The largest emission intensity is observed when the QD line is in perfect resonance with the cavity mode. Resonance temperatures of the sources presented here are between 10 K and 21 K.

Figure 2a presents the emission spectrum of pillar 2 with a pump laser tuned to 860 nm to create carriers in the wetting layer. At resonance between the exciton line and the cavity mode(10 K), only a single QD emission line is visible on a 90-nm wavelength spectral window. For this line, a 26530 ps decay time is measured (Fig. 2b), corresponding to a Purcell factor of3.90.6. A similar Purcell factor is measured for pillar 1, as shown in Fig. 2b. The count rate measured on one SPAD is presented in Fig. 2c as a function of incident power for both pillars. At saturation, the count rate is around 0.7 MHz. To deduce the corresponding number of photons collected per excitation pulse in the rst lens, we calibrate all the optical components of the detection path (Table 1). This count rate corresponds to a value as large as 0.9 photons collected per excitation pulse in the rst lens. As recapture processes may affect this value by increasing the probability that more than one photon is emitted per excitation pulse, autocorrelation measurements are performed. We observe that the second order autocorrelation function at zero delay g(2)(0) is below 0.15 up to

a

c

100%

800

200

PL intensity (arb. u.)

Collected photons per pulse

80%

600

60%

400

Count rate (kHz)

40%

920

940

960

980

Pillar 1

Wavelength (nm)

1000

20%

Pillar 2

b

0%

PL intensity (arb. u.)

1

0.75

g2(0)

g2()

0.5

0.25

0 12.2 12.2 Delay T (ns)

0

Pillar 1

0 1 1.5 Time (ns)

Pillar 2

0

0.5 0 1 2

3

Pump power (W)

0

Figure 2 | Brightness of the single-photon source (a) PL spectrum of pillar 2 at spectral resonance with the cavity mode (10 K) and for an excitation power above the exciton line saturation. arb. u., arbitrary units. (b) PL intensity as a function of time for the exciton line in pillar 1 and 2. A lifetime around 265270 ps is deduced after deconvolution with the temporal response of the system. Reference QDs in unprocessed planar cavity show decay time of1.3 ns (not shown). (c) Top: Raw (open symbols) and multi-photon corrected (solid symbols) number of collected photons per laser pulse for pillar 1 (squares) and pillar 2 (circles). Bottom: Measured g(2)(0) values as a function of the pump power. Inset: example of an antibunching curve measured at 2 mW for pillar 1. For all gures, the excitation laser is tuned to 860 nm to create carriers in the wetting layer.

NATURE COMMUNICATIONS | 4:1425 | DOI: 10.1038/ncomms2434 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications 3

& 2013 Macmillan Publishers Limited. All rights reserved.

ARTICLE NATURE COMMUNICATIONS | DOI: 10.1038/ncomms2434

saturation so that the multi-photon correction term (1-g(2)(0))1/2 only slightly modies the extremely high brightness (Fig. 2c). We thus obtain an experimentally measured brightness of 788%.

Very high brightnesses ranging from 546% to 798% are measured on several pillar cavities in a 0.4 numerical aperture as shown in Table 2. We also present the brightness of a QD line coupled to the mode of coupled pillars, a cavity which we recently used to collect entangled photon pairs8. For each source, we measure the lifetime of the QD transition and deduce the experimentally measured b FP/(FP 1) within a 1020% error

bar due to the nite time resolution of the photodiodes. While Q cannot be easily measured on the pillars embedding a single QD, we estimate that Q/Q0 0.950.05 from measurements on

pillars embedding a high QD density. As shown in Table 2, we observe a good agreement within error bars between the directly measured brightness and the measured expected value FP/(FP 1) Q/Q0.

Indistinguishability and high brightness. To prove the indistinguishability of two consecutively emitted photons, we implement the Hong Ou Mandel two-photon interference experiment1 (Fig. 3a). The pillar 2 source is excited twice every laser pulse using a 2.2 ns delay line. Both emitted photons enter into a Michelson interferometer with a 2.2 ns delay between the two arms. Both photons exit the interferometer by the same output if they are Fourier-transform limited and present identical spatial mode, temporal prole, energy and polarization. Here the Purcell effect, implemented to collect the photons, also ensures that their spatial mode is the one of the cavity mode. Usually, polarization and energy properties are strongly related to the QD exciton transition. Indeed, because of anisotropy in the carrier wavefunctions, a single QD presents two exciton states with orthogonal linear polarizations. If this polarization splitting S is larger than the linewidth of the emission line, the photons emitted by the QD are indistinguishable only in the linear polarization basis corresponding to the QD axis16. Here we study

annealed InGaAs QDs, similar to the one used to produce entangled photon pairs8. In this case, S is below 2 meV so that

Purcell effect leads to a radiative broadening of the exciton line overcoming the polarization splitting S. As a result, contrary to previous demonstrations16,17,19, we select any arbitrary linear polarization by inserting a polarizer before the interferometer. Finally, to reduce the effect of dephasing and obtain Fourier-transform limited photons, we take advantage of the Purcell effect to shorten the exciton lifetime19 and investigate various excitation schemes. Note that the dephasing time of the emission lines measured as in ref. 7 does not relate to the photon indistinguishability measured using the Hong Ou Mandel experiment. Indeed, the latter measurement tests the indistinguishability of photons emitted 2.2 ns apart by the same QD. Longer time scale dephasing can broaden the emission line while not degrading the two-photon interference visibility.

We rst study the indistinguishability under non-resonant excitation in the wetting layer at 860 nm. The Fig. 3c presents a correlation histogram of the interferometer two outputs at low excitation power. Peak at 0 delay corresponds to both photons entering the beam splitter simultaneously (the rst photon follows the long arm of the interferometer and the second one the short arm). For a pure single-photon source with perfect indistinguishability, peak at 0 delay should vanish1. Deviation from this ideal situation arises from intrinsic properties of the sources, as well as imperfect instrumentation. Following ref. 16 to account for these various contributions (see Methods), we deduce a mean wave packet overlap M of 8610%, a very high value for non-resonant excitation conditions. As shown in Fig. 3b, M decreases when increasing the excitation power, to reach 538% at maximum brightness of the source (green squares). The right scale shows the excitation power normalized to the saturation power P/Psat as a function of the source brightness given by I bZqQD (1- e-P/Psat). Upon excitation

power increase, the increasing number of carriers created in the wetting layer leads to uctuations of the QD electrostatic environment and dephasing.

To avoid this effect, resonant excitation in the p shell of the single QD state is used (906 nm). As shown in Fig. 3d, a lower wave packet overlap is obtained in this resonant excitation condition. A mean wave packet overlap around 50% is observed for all the excitation powers, up to saturation (red triangle in Fig. 3b). The observation of such a low visibility under resonant excitation indicates that dephasing comes from uctuations of the electrostatic environment around the QD. This observation is in contradiction with previous reports of high indistinguishabilities using p-shell resonant excitation16,17. Considering these two sets of measurements, we can conclude that under low power non-resonant excitation, non-resonantly created carriers ll deep traps around the QD and stabilize the QD electrostatic environment, enabling the observation of very high indistinguishability.

Table 1 | Experimental set-up calibration.

Transmission/ efciency

Error bar

Cryostat windows (uncoated) 0.90 4% Microscope objective 0.46 4% 80/20 NPBS 0.75 4% 50/50 NPBS 0.49 4% Detection efciency 0.11 6% Overall detection efciency 0.017 10%

SPAD, single-photon avalanche diode; NPBS, non polarizing beam splitter.

Transmission values of all optical elements of the detection path and detection efciency. The detection efciency includes the spectrometer transmission, the two coupling lenses and the Perkin-Elmer SPAD efciency.

Table 2 | Experimental brightness of several sources.

Pillar 1 Pillar 2 Pillar 3 Pillar 4 Coupled pillar Lifetime (ps) 27030 26530 28030 55030 47030

Purcell factor FP 3.80.5 3.90.6 3.640.5 1.360.13 1.750.18 FP/(FP 1) (%) 7916 8017 7816 5810 6412

FP/(FP 1) Q/Q0 (%) 7516 7616 7516 5510 6011

Collected photon per pulse (%) 798 788 687 546 647

Summary of the characteristics of several sources fabricated with the in situ lithography for a spectral resonance between the QD exciton line and the cavity mode obtained for a temperature between 10 and 21 K. We indicate the lifetime of the exciton line measured at low power, the corresponding Purcell effect, the expected coupling to the mode F /(F 1), the maximal expected brightness Q/Q

F /(F 1) and the measured number of photons collected per excitation pulse.

4 NATURE COMMUNICATIONS | 4:1425 | DOI: 10.1038/ncomms2434 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications

& 2013 Macmillan Publishers Limited. All rights reserved.

NATURE COMMUNICATIONS | DOI: 10.1038/ncomms2434 ARTICLE

a

Laser pulse

2.2ns delay

c

2.2ns

NPBS

300

0

Wetting layer

4.4 0 4.4 Delay T (ns)

Microscope objective 0.4 NA

Polarizer

Sample Cryostat 10K

Spectrometers CCDs + SPADs

Retroreflector

0

d

p shell

p shell + 10% WL

120

b

1.0

8

4

Coincidences

Mean wave packet overlap

0.8

6

0.6

e

P/P sat

150

0.4

0.2

2

0.0

0

0

0%

20%

40%

60%

80%

Collected photons per pulse

100%

Figure 3 | Indistinguishability of the photons (pillar 2). (a) Experimental set-up used for indistinguishability measurements. (b) Mean wave packet overlap as a function of the number of collected photon per pulse for three excitation conditions. Square: pulsed excitation at 860 nm in the wetting layer. Triangle: pulsed excitation at 906 nm in the p shell of the QD. Stars: pulsed excitation in the p shell, with additional continuous wave excitation in the wetting layer contributing to 10% of the signal. Right scale: Excitation power P normalized to the saturation power Psat as a function of the source brightness (solid black line). The dotted vertical line shows the maximum brightness of the source. Error in the evaluation of M comes from uncertainties in the tting procedure of the various peak areas (see Methods). (ce) Pulsed correlation histograms between the two SPADs for three excitation conditions indicated by the open symbols in Fig. 3b. Experimental curves are blue symbols. Shaded curves are t to the data with Lorentzian peaks. The measured mean wave packet overlap is M 86% for c, M 48% for d and M 92% for e. CCD, charge coupled device; NPBS, non polarizing beam splitter; WL, wetting layer.

Therefore, to obtain high indistinguishability combined with high brightness, we use p-shell strong excitation to saturate the QD transition while a second weak 860 nm continous wave excitation is applied to stabilize the QD electrostatic environment. Blue stars in Fig. 3b presents the corresponding experimental points where for each resonant excitation power, the second 860 nm laser produces 10% of the total intensity. The bottom scale then corresponds to the brightness due to the pulsed laser only.

For all excitation powers up to 3Psat, the two colour excitation

scheme allows obtaining greatly improved indistinguishability as compared with single excitation schemes. For instance, the two colour experiment allows doubling the brightness as compared with a single colour scheme for a xed mean wave packet overlap around 80%. A mean wave packet overlap of 9211% is measured for a source brightness of 0.530.05 collected photons per pulse (Fig. 3e). This value remains as high as 8210% for a brightness as large as 0.650.06 collected photon per pulse, corresponding to 2Psat.

DiscussionRecent reports on QD spectroscopy have shown a strong instability of the QD charge state under strictly resonant excitation2830, which could be overcome using a second non-resonant excitation with very low power. In the present measurement, the very high brightness of the source is observed either using wetting layer or p shell excitation, showing a very stable QD charge state. Here, the second laser helps minimizing uctuations of carriers around the QDs, leading to a reduced dephasing and improved indistinguishability.

To further increase both the source brightness and the photon indistinguishability, one could consider using the recently

proposed adiabatic design of the cavity31, which makes the pillar mode less sensitive to the sidewall roughness. Using such a design, one could, therefore, further increase the Purcell factor hence b, while maintaining a good mode coupling to the external optical eld. Stronger Purcell effect would also allow improving the indistinguishability by reducing the inuence of fast dephasing16,19.

Our work shows that ultrabright sources of single photons can be obtained thanks to a full control of the QD-pillar cavity system. High brightness and high indistinguishability can be combined thanks to an additional weak non-resonant excitation. Our results open the way to increasing the number of logic gates in optical quantum computers3 thanks to the quantum statistics, high brightness and indistinguishability of QD-based sources.

Methods

Sample fabrication. The sample, grown by molecular been epitaxy, consists of a l-cavity between two l/4n GaAs/Al0.9Ga0.1As Bragg reectors with 16 (36) pairs for the top (bottom) mirror. A layer of InGaAs QDs is inserted in the cavity. The sample is annealed at 850 1C for 30 s to reduce the QD anisotropic polarization splitting. The in situ lithography technique is used to dene pillars centred on single QDs14: a red laser beam is used to excite and monitor the QD emission so as to measure its spatial position with 50 nm accuracy. A green laser beam is used to expose a disk centred on the QD in a photoresist spin-coated on the sample. The in situ lithography was done using an attocube equipment (attoCFM for low temperature photolithography).

Measuring the pillar Q factor. To measure the planar cavity quality factor, we image the planar cavity mode dispersion and measure the cavity spectral linewidth at normal incidence. In Fig. 1c, the curve Q/Q0 is a t to measured Q factors on a sample with the same number of pairs in the mirrors but embedding a large QD density.

Extraction efciency measurements. To measure the extraction efciency of the source, all optical elements of the detection path have been calibrated using a continuous wave laser at 930 nm (Table 1). The transmission of the spectrometer

NATURE COMMUNICATIONS | 4:1425 | DOI: 10.1038/ncomms2434 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications 5

& 2013 Macmillan Publishers Limited. All rights reserved.

ARTICLE NATURE COMMUNICATIONS | DOI: 10.1038/ncomms2434

and the detection efciency of the SPAD are estimated by measuring a pulsed laser signal of known power for which we can deduce the number of incident photons per pulse.

Hanbury-Brown and Twiss interferometer. The Hanbury-Brown and Twiss interferometer is composed of a 50/50 non-polarizing beam splitter (NPBS), which sends PL signals into (spectrometers coupled to SPADs).

Indistinguability measurements. To check the spatial overlap of the two photons in free space on the beam splitter, we take advantage of the source brightness to directly image the photon spatial modes on a liquid nitrogen cooled CCD.

In the histograms presented in Fig 3ce, Peak 0 (at 0 delay) corresponds to both photons entering the beam splitter simultaneously, peaks 1 (at -2.2 ns) and 1

(at 2.2 ns) correspond to the case where both photons take the same path. Peaks

2 (at -4.4 ns) and 2 (at 4.4 ns) correspond to rst (second) photon following

the short (long) arm. From obtained correlations histograms and from formulas, which give relative amplitude A 2 to A2 of the ve peaks in the centre of the

histogram16, we deduce the value of the mean wave packet overlap M of two successive photons:

A 2 NR3T 1

A 1 N R3T 1 2g

RT3

2

A0 N R3T RT3

1 2g

21 e2R2T2M 3

A1 N R3T RT3 1 2g

4

A2 NRT3 5 R 0.476 and T 0.504 are reection and transmission values of the beam splitter

cube, e 0.95 is the interference fringe contrast measured when monomode CW

laser at 920 nm is sent into the interferometer. It accounts for optical surfaces imperfections. g is the autocorrelation function at zero delay g2(0), and the common prefactor N is related to the number of detected events.

Error in the evaluation of M comes from uncertainties in the tting procedure of the various peak areas and in the measurements of g and e. The resulting error bars are displayed in Fig. 3b.

References

1. Hong, C. K., Ou, Z. Y. & Mandel, L. Measurement of subpicosecond time intervals between two photons by interference. Phys. Rev. Lett. 59, 20442046 (1987).

2. Knill, E., Laamme, R. & Milburn, G. J. A scheme for efcient quantum computation with linear optics. Nature 409, 4652 (2001).

3. Lanyon, B.P. et al. Towards quantum chemistry on a quantum computer. Nat. Chem. 2, 106111 (2010).

4. Gisin, N., Ribordy, G., Tittel, W. & Zbinden, H. Quantum cryptography. Rev. Mod. Phys. 74, 145195 (2002).

5. de Riedmatten, H., Marcikic, I., Tittel, W., Zbinden, H., Collins, D. & Gisin, N. Long distance quantum teleportation in a quantum relay conguration. Phys. Rev. Lett. 92, 047904 (2004).

6. Michler, P. et al. A quantum dot single-photon turnstile device. Science 290, 22822285 (2000).

7. Pelton, M. et al. Efcient source of single photons: a single quantum dot in a micropost microcavity. Phys. Rev. Lett. 89, 233602 (2002).

8. Dousse, A. et al. Ultrabright source of entangled photon pairs. Nature 466, 217220 (2010).

9. Claudon, J. et al. A highly efcient single-photon source based on a quantum dot in a photonic nanowire. Nat. Photon. 4, 174177 (2010).

10. Strauf, S. et al. High-frequency single-photon source with polarization control. Nat. Photon. 1, 704708 (2007).

11. Bayer, M., Stern, O., Hawrylak, P., Fafard, S. & Forchel, A. Hidden symmetries in the energy levels of excitonic articial atoms. Nature 405, 923926 (2000).

12. Young, R. J. et al. Improved delity of triggered entangled photons from single quantum dots. New J. Phys. 8, 29 (2006).

13. Akopian, N. et al. Entangled photon pairs from semiconductor quantum dots. Phys. Rev. Lett. 96, 130501 (2006).

14. Grard, J. M. & Gayral, B. Strong purcell effect for Inas quantum boxes in three dimensional solid-state microcavities. J. Lightwave Technol. 17, 20892095 (1999).

15. Lund-Hansen, T. et al. Experimental realization of highly efcient broadband coupling of single quantum dots to a photonic crystalwaveguide. Phys. Rev. Lett 101, 113903 (2008).

16. Santori, C., Fattal, D., Vukovi, J., Solomon, G. S. & Yamamoto, Y. Indistinguishable photons from a single-photon device. Nature 419, 594597 (2002).

17. Ates, S. et al. Post-Selected indistinguishable photons from the resonance uorescence of a single quantum dot in a microcavity. Phys. Rev. Lett. 103, 167402 (2009).

18. Stevenson, R. M. et al. Indistinguishable entangled photons generated by a light-emitting diode. Phys. Rev. Lett. 108, 040503 (2012).

19. Varoutsis, S. et al. Restoration of photon indistinguishability in the emission of a semiconductor quantum dot. Phys. Rev. B 72, 041303 (2005).

20. Bennett, A. J. et al. Indistinguishable photons from a diode. Appl. Phys. Lett. 92, 193503 (2008).

21. Dousse, A. et al. Controlled light-matter coupling for a single quantum dot embedded in a pillar microcavity using far-eld optical lithography. Phys. Rev. Lett. 101, 267404 (2008).

22. Grard, J. M. et al. Enhanced Spontaneous emission by quantum boxes in a monolithic optical microcavity. Phys. Rev. Lett. 81, 11101113 (1998).

23. Arnold, C. et al. Optical bistability in a quantum dots/micropillar device with a quality factor exceeding 200 000. Appl. Phys. Lett. 100, 111111 (2012).

24. Benisty, H., De Neve, H. & Weisbuch, C. Impact of planar microcavity effects on light extractionpart I: basic concepts and analytical trends. IEEE J. Quant. Electron. 34, 16121631 (1998).

25. Barnes, W.L. et al. Solid-state single photon sources: light collection strategies. Eur. Phys. J. D 18, 197210 (2002).

26. Gazzano, O. et al. Evidence for Conned tamm plasmon modes under metallic microdisks and application to the control of spontaneous optical emission. Phys. Rev. Lett. 107, 247402 (2011).

27. Kiraz, A. et al. Photon correlation spectroscopy of a single quantum dot. Phys. Rev. B 65, 161303 (2002).

28. Muller, A., Fang, W., Lawall, J. & Solomon, G. S. Emission spectrum of a dressed exciton-biexciton complex in a semiconductor quantum dot. Phys. Rev. Lett. 101, 027401 (2008).

29. Metcalfe, M., Carr, S. M., Muller, A., Solomon, G. S. & Lawall, J. Resolved sideband emission of inas/gaas quantum dots strained by surface acoustic waves. Phys. Rev. Lett 105, 037401 (2010).

30. Nguyen, H. S. et al. Optically gated resonant emission of single quantum dots. Phys. Rev. Lett. 108, 057401 (2012).

31. Lermer, M. et al. Bloch-wave engineering of quantum dot micropillars for cavity quantum electrodynamics experiments. Phys. Rev. Lett. 108, 057402 (2012).

Acknowledgements

This work was partially supported by the French ANR P3N DELIGHT, ANR JCJC MIND, the ERC starting grant 277885 QD-CQED, the French RENATECH network and the CHISTERA project SSQN. O.G. acknowledges support by the French Dlgation Gnrale de lArmement.

Author contributions

O.G. performed the optical measurements and data analysis. S.M.d.V., A.N. and C.A. fabricated the devices. A.L. and E.G. grew the sample. I.S. etched the pillars. P.S. conducted the project. All authors participated to scientic discussions and manuscript preparation.

Additional information

Competing nancial interests: The authors declare no competing nancial interests.

Reprints and permission information is available online at http://npg.nature.com/reprintsandpermissions/

Web End =http://npg.nature.com/ http://npg.nature.com/reprintsandpermissions/

Web End =reprintsandpermissions/

How to cite this article: Gazzano O. et al. Bright solid-state sources of indistinguishable single photons. Nat. Commun. 4:1425 doi: 10.1038/ncomms2434 (2013).

6 NATURE COMMUNICATIONS | 4:1425 | DOI: 10.1038/ncomms2434 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications

& 2013 Macmillan Publishers Limited. All rights reserved.