On the interchannel interference in digital communication systems, its impulsive nature, and its mitigation

Abstract

A strong digital communication transmitter located in close physical proximity to a receiver of a weak signal can noticeably interfere with the latter even when the respective channels are tens or hundreds of megahertz apart. When time domain observations are made in the signal chain of the receiver between the first mixer and the baseband, this interference is likely to appear impulsive. Understanding the mechanism of this interference is important for its effective mitigation. In this article, we show that impulsiveness, or a high degree of peakedness, of interchannel interference in communication systems results from the non-smooth nature of any physically realizable modulation scheme for transmission of a digital (discontinuous) message. Even modulation schemes designed to be 'smooth', e.g., continuous-phase modulation, are, in fact, not smooth because their higher order time derivatives still contain discontinuities. When observed by an out-of-band receiver, the transmissions from these discontinuities may appear as strong transients with the peak power noticeably exceeding the average power, and the received signal will have a high degree of peakedness. This impulsive nature of the interference provides an opportunity to reduce its power by nonlinear filtering, thus improving quality of the receiver channel.[PUBLICATION ABSTRACT]

Nikitin EURASIP Journal on Advances in Signal Processing 2011, 2011:137 http://asp.eurasipjournals.com/content/2011/1/137

RESEARCH Open Access

On the interchannel interference in digital communication systems, its impulsive nature, and its mitigation

Alexei V Nikitin1,2

Abstract

A strong digital communication transmitter located in close physical proximity to a receiver of a weak signal can noticeably interfere with the latter even when the respective channels are tens or hundreds of megahertz apart. When time domain observations are made in the signal chain of the receiver between the first mixer and the baseband, this interference is likely to appear impulsive. Understanding the mechanism of this interference is important for its effective mitigation. In this article, we show that impulsiveness, or a high degree of peakedness, of interchannel interference in communication systems results from the non-smooth nature of any physically realizable modulation scheme for transmission of a digital (discontinuous) message. Even modulation schemes designed to be smooth, e.g., continuous-phase modulation, are, in fact, not smooth because their higher order time derivatives still contain discontinuities. When observed by an out-of-band receiver, the transmissions from these discontinuities may appear as strong transients with the peak power noticeably exceeding the average power, and the received signal will have a high degree of peakedness. This impulsive nature of the interference provides an opportunity to reduce its power by nonlinear filtering, thus improving quality of the receiver channel.

Keywords: electromagnetic interference, impulsive noise, interchannel interference, nonlinear differential limiters, nonlinear filtering, peakedness

1 Introduction

Nowadays, it is becoming more and more common that multiple digital communication devices, including wireless, coexist and concurrently operate in close physical proximity. A typical example would be a smartphone equipped with WiFi, Bluetooth, and GPS, and capable of operating at various data protocols and in multiple frequency bands. This physical proximity, combined with a wide range of possible transmit and receive powers, creates a variety of challenging interference scenarios. Multiple sources of empirical evidence indicate that such interference often manifests itself as impulsive noise [1,2], which in some instances dominates over the thermal noise [1,3]. However, there are many unanswered questions regarding the origins and the particular manifestations of this type of noise. For example, a strong close transmitter (say, WiFi) can noticeably interfere

with a receiver of a weak signal (say, GPS) even when the separation of their frequency bands exceeds the respective nominal bandwidths of the channels by orders of magnitude. When time domain observations of such far-out-of-band interference are made at the receiver frequency, in a relatively wide bandwidth to avoid excessive broadening of the transients, this interference is likely to appear impulsive. Understanding the mechanism of this interference and its impulsive nature, as initially analyzed in [4], is important for its effective mitigation.

Referring to a signal as impulsive implies that the distribution of the instantaneous power of the signal has a high degree of peakedness relative to some standard distribution, such as the Gaussian distribution. A common quantifier of peakedness would be, for instance, the excess kurtosis [5]. In this article, however, we adopt the measure of peakedness relative to a constant signal as the excess-to-average power ratio and use the units

Correspondence: mailto:[email protected]

Web End [email protected]

1Avatekh Inc., 900 Masachusetts Street, Suite 409, Lawrence, KS 66044, USA Full list of author information is available at the end of the article

2011 Nikitin; licensee Springer. This is an Open Access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/2.0

Web End =http://creativecommons.org/licenses/by/2.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Nikitin EURASIP Journal on Advances in Signal Processing 2011, 2011:137 http://asp.eurasipjournals.com/content/2011/1/137

Page 2 of 10

6 s

W 6 s

1 Mbit/s modulation

1.045 GHz

notch at 1.045 GHz

1 GHz gain

Out-of-band receiver (f = 45 MHz)

1.045 GHz transmitter

Figure 1 Illustrative measuring setup for demonstration of impulsive nature of interchannel interference.

decibels relative to constant or dBc. This measure is explained in Appendix A.

Let us consider the illustrative measurement with the setup shown in Figure 1. In the left-hand panel of the figure, the transmitter emits a 1.045-GHz tone with the amplitude modulated by a smooth-looking 1 Mbit/s message. However, as can be seen in the right-hand panel, the total instantaneous power in an out-of-band quadrature receiver [6] with the bandwidth of several megahertz, tuned to 1 GHz, is an impulsive pulse train with a multiple of 250 ns distance between the pulses.

Figure 2 provides a closer look at the time domain signal traces of the modulating signal (lower panel) and the observed instantaneous power in the receiver (upper panel) for the setup shown in Figure 1. One can see

that the power trace is impulsive as its peaks significantly extend above the average power level indicated by the horizontal solid line. Note that some of the peaks of the instantaneous power originate at zero modulation amplitude (at onsets and ends of the modulating pulses), while others originate at the smoothest, most linear parts of the modulating signal. The next section clarifies the origins of this impulsive nature of the out-of-band interference.

2 Impulsive nature of interchannel interference

As shown in more detail in Appendix B, the signal components induced in a receiver by out-of-band communication transmitters can be impulsive. For example, if the receiver is a quadrature receiver with identical low-pass

Measured out-of-band p ower at f = 45 MHz

power

0

1 Mb/ s mo dulating sig nal

amplitude

0

1 1.25 1.75 2.25 2.75 3 3.25 3.75 4 4.25 4.75 5 6 6.25 6.75 7

ti me (s)

Figure 2 Closer look at the time domain signal traces for the setup shown in Figure 1. The modulating signal is shown in the lower panel, and the observed instantaneous power in the receiver shown in the upper panel.

Nikitin EURASIP Journal on Advances in Signal Processing 2011, 2011:137 http://asp.eurasipjournals.com/content/2011/1/137

Page 3 of 10

A typical value of ti+1-ti would be of the same order of magnitude as T. If the reciprocal of this value is small in comparison with the bandwidth of the receiver, the contribution of the terms ijh (t ti) h (t tj) for i j is

negligible and (2) describes an impulsive pulse train consisting of a linear combination of pulses shaped as w2(t) and originating at {ti}, namely

Px(t, f ) = 1

(T f )2n

i

|i |2h2(t ti)

for sufciently large T and f .

filters in the channels, the main term of the total instantaneous power of in-phase and quadrature components resulting from such out-of-band emissions may appear as a pulse train consisting of a linear combination of pulses originating at discrete times and shaped as the squared impulse response of these filters. For a single transmitter, the typical intervals between those discrete times are multiples of the symbol duration (or other discrete time intervals used in the designed modulation scheme, for example, chip and guard intervals). The non-idealities in hardware implementation of designed modulation schemes such as the non-smooth behavior of the modulator around zero also contribute to additional discrete origins for the pulses. If the typical value of those discrete time intervals is large in comparison with the inverse bandwidth of the receiver, this pulse train may be highly impulsive.

The above paragraph can be restated using mathematical notations as follows. The total emission from various digital transmitters can be written as a linear combination of the terms of the following form:

x(t) = AT(t) ei

ct, (1)

where c is the frequency of a carrier, t = 2T t is dimensionless time, and AT(t) is the desired (or

designed) complex-valued modulating signal representing a data signal with symbol duration T. Let us assume that the impulse response of the low-pass filters in both channels of a quadrature receiver is w(t) = 2T h(t) and

that the order of the filter is larger than n so that all derivatives of w(t) of order smaller or equal to n - 1 are continuous.a Now let us assume that all derivatives of the same order of the modulating signal AT(t) are finite, but the derivative of order n - 1 of AT(t) has a countable number of step discontinuitiesb at {ti}. Then, if

= 2f is the difference between the carrier and the receiver frequencies, and the bandwidth of the low-pass filter w(t) in the receiver is much smaller than f, the total power in the quadrature receiver due to x(t) can be expressed asc

Px(t, f ) = 1(T f )2n

iih (t ti)

jj h (t ti)

for T f 1 ,

(4)

Equipped with (4), let us reexamine the time domain traces of the illustrative measurement outlined in Figure1. In Figure 3, these traces are expanded to include the first two time derivatives of the modulating signal. It can be seen in the figure that (i) the onsets of the power pulses originate at the discontinuities in the second derivative of the modulating signal and (ii) the magnitudes of those pulses are proportional to the squared magnitudes of the discontinuities. Both observations are compliant with (4).

As an additional illustration of a pulse train according to (4), panel I of Figure 4 shows simulated instantaneous total power response of quadrature receivers tuned to 1-and 3-GHz frequencies (green and black lines, respectively) to an amplitude-modulated 2-GHz carrier of unit power. The squared impulse response of the low-pass filter in the receiver channels (30 MHz 5th order Butter-worth filter [7] is indicated in the upper right corner of the panel.

The modulating signal is shown in panel II(a) of the figure and represents a random bit sequence at 10 Mbit/s (T = 100 ns). In this example, a highly over-sampled FIR raised cosine filter [6] with roll-off factor0.35, and group delay 2T was used for pulse shaping. A rather small group delay was chosen to make the discontinuities in the derivative more visible in the figure. Panel II(b) of Figure 4 shows the first derivative of the modulating signal. This derivative exhibits step discontinuities at the multiple of T time intervals (at the time ticks), and thus n = 2 in (2).

It is important to notice that the impulsive pulse train is not necessarily caused directly by the discontinuities in the amplitude and/or phase of the transmitted signal, but rather by the discontinuities in the higher order derivatives of the modulating signal, and is generally unrelated to the magnitude of the envelope and/or the peak-to-average ratio of the transmitted signal. Thus, for instance, continuous-phase modulation (CPM), while generally reducing the magnitude of the impulsive inter-

(2)

where ai is the value of the ith discontinuity of the order n - 1 derivative of AT(t),

i = lim

0

A(n1)T(ti + ) A(n1)T(ti )

= 0. (3)

Nikitin EURASIP Journal on Advances in Signal Processing 2011, 2011:137 http://asp.eurasipjournals.com/content/2011/1/137

Page 4 of 10

Measured out-of-band p ower at f = 45 MHz

power

0

1 Mb/ s mo dulating sig nal

amplitude

0

1st der i vati ve of mo dul ati ng si gnal

2nd der i vati ve of mo dul ati ng si gnal

1 1.25 1.75 2.25 2.75 3 3.25 3.75 4 4.25 4.75 5 6 6.25 6.75 7

time (s)

Figure 3 Expanded time domain traces for the illustrative measurement outlined in Figure 1. In addition to the modulating signal and the instantaneous total power response of the quadrature receiver, the first two time derivatives of the modulating signal are also shown.

ference by increasing the order of the first discontinuous derivative by one, does not eliminate the effect altogether. This is illustrated in Appendix C.

When viewed as a function of both time and frequency, the interpretation of (2) for the total power in a quadrature receiver is a spectrogram [8] in the time window w(t) of the term x(t) of the transmitted signal. Such a spectrogram is shown in the lower panel of Figure 4, where the horizontal dashed lines indicate the receiver frequencies 1 and 3GHz used in panel I.

For a quantitative illustration of the impulsive nature of the out-of-band interference, the upper panel of Figure 5 shows the peakedness of the instantaneous total power in a quadrature receiver as a function of frequency for the example used in Figure 4. The peakedness of the out-of-band signal exceeds the peakedness of the in-band signal by over an order of magnitude.

The lower panel of Figure 5 shows, for the same examples, the total excess (solid line) and average (dashed line) power in the receiver versus frequency. The excess power of the out-of-band emissions is approximately 10 dB higher than the average power.

Given the designed properties of the transmitted signal, the out-of-band emissions can be partially mitigated by additional filtering. For example, one can apply additional high-order low-pass filtering to the modulating signal or band-pass filtering to the modulated carrier. However, the bandwidth of those additional filters must be sufficiently large in comparison with the bandwidth of the pulse shaping filter in the modulator in order to not significantly affect the designed signal. Within that bandwidth, the above analysis still generally holds, and the impulsive disturbances may significantly exceed the thermal noise level in the receiver [3] even when the

Nikitin EURASIP Journal on Advances in Signal Processing 2011, 2011:137 http://asp.eurasipjournals.com/content/2011/1/137

Page 5 of 10

Instantaneous total power responses of quadrature receivers at 1 GHz (green) and 3 GHz (black) to amplitude-modulated 2 GHz tone of unit power

w2(t)

30 MHz 5th order lowpass Butterworth

I2(t)+Q2(t)

I

10 Mbit/s modulating signal

II(a)

Derivative of modulating signal

II(b)

Spectrogram in time window w(t) of amplitude-modulated 2 GHz tone

w(t)

w(t)

w(t)

w(t)

w(t)

frequency(GHz)

time (s)

Figure 4 Additional illustration of a pulse train according to (4). Panel I of the figure shows simulated instantaneous total power response of quadrature receivers tuned to 1- and 3-GHz frequencies (green and black lines, respectively) to an amplitude-modulated 2-GHz carrier of unit power. The squared impulse response of the low-pass filters in the receiver channels is shown in the upper right corner of the panel. Panels II(a) and II(b) of the figure show the modulating signal and its first derivative, respectively. For the modulating signal shown in the figure, n = 2 in(2). The lower panel of the figure shows instantaneous total power response of a quadrature receiver as a spectrogram in the time window w(t) shown in the upper left corner of the panel.

Nikitin EURASIP Journal on Advances in Signal Processing 2011, 2011:137 http://asp.eurasipjournals.com/content/2011/1/137

Page 6 of 10

Peakedness in dBc of excess-to -averag e power

peakedness(dBc)

Excess (solid line) and average (dashed line) total power

power(dB)

fr equ en cy (GHz)

Figure 5 Peakedness of the instantaneous total power as a function of frequency for the example used in Figure 4. Upper panel shows peakedness in dBc of the instantaneous total power response of a quadrature receiver as a function of frequency. The horizontal dashed line corresponds to the peakedness of a Gaussian distribution. The lower panel shows the total excess (solid line) and average (dashed line) power in the receiver versus frequency. The transmitted signal is a 2-GHz carrier amplitude-modulated by a random 10 Mbit/s bit stream. The impulse response w(t) of the receiver and the pulse shaping of the modulating signal are as in the example shown in Figure 4.

average power of the interference remains below that level.

3 Conclusions

Non-smoothness of modulation can be caused by a variety of hardware imperfections and, more fundamentally, by the very nature of any modulation scheme for digital communications. This non-smoothness sets the conditions for the interference in out-of-band receivers to appear impulsive.

If the coexistence of multiple communication devices in, say, a smartphone is designed based on the average power of interchannel interference, a high excess-to-average power ratio of impulsive disturbances may degrade performance even when operating within the specifications.

On the other hand, the impulsive nature of the interference provides an opportunity to reduce its power. Since the apparent peakedness for a given transmitter depends on the characteristics of the receiver, in particular its bandwidth, an effective approach to mitigating the out-of-band interference can be as follows: (i) allow the initial stage of the receiver to have a relatively large bandwidth so that the transients are not excessively broadened and the out-of-band interference remains highly impulsive, then (ii) implement the final reduction of the bandwidth to within the specifications through nonlinear means, such as the analog filters described in [9-13]. For instance, the differential over-limiter (DoL) described in Appendix D is effective in mitigation of impulsive noise. Using DoL improves the signal-to-noise ratio and increases the data rates of a communication

Nikitin EURASIP Journal on Advances in Signal Processing 2011, 2011:137 http://asp.eurasipjournals.com/content/2011/1/137

Page 7 of 10

channel (e.g., GPS or WCDMA) in the presence of interchannel interference, for example, from WiFi transmissions. An experimental study of the mitigation of the impulsive interference induced in 1.95-GHz High Speed Downlink Packet Access (HSDPA) by 2.4-GHz WiFi transmissions, protocols that coexist in many 3G smart-phones and mobile hotspots, is presented in Impulsive interference in communication channels and its mitigation by SPART and other nonlinear filters by AV Nikitin, M Epard, JB Lancaster, RL Lutes, and EA Shumaker, currently under consideration for publication in the EURASIP Journal on Advances in Signal Processing.

Appendix A

Excess-to-average power ratio as measure of peakedness Consider a signal x(t). Then, the measure Kc of its peakedness in some time interval can be defined implicitly as the excess-to-average power ratio

x2(t)

x2(t) Kc

= 1

where the asterisk denotes convolution, and I (t, ) and Q (t, ) can be interpreted as the in-phase and quadrature components, respectively, of a quadrature receiver with the local oscillator frequency and the impulse response of low-pass filters in the channels w(t).

Let us use the notation for dimensionless time as

t = 2T t and consider a transmitted signal x(t) of the form

x(t) = AT(t) ei

ct, (8)

where c is the frequency of the carrier, and AT(t) is

the desired (or designed) complex-valued modulating signal representing a data signal with symbol duration T.

The windowed Fourier transform of x(t) can be written as

X(t, ) =

d AT(

) w(t )ei

= 2

T

(9)

2, (5)

where (x) is the Heaviside unit step function, denotes averaging over the time interval, and x2(t) = x2(t)/ x2(t) is normalized instantaneous signal

power. Kc = 1 for x(t) = const, and thus KdBc = 10 lg (Kc) expresses excess-to-average power ratio in units of decibels relative to constant.

For a Gaussian distribution, Kc is the solution of

32,Kc 2

d[AT(

) h (t )]

d d

ei

i

,

= 2T and = 2 f = c - . Since w(t) and all its derivatives vanish outside the interval [0, ], consecutive integration by parts leads to

X(t, f ) = in

(T f )n

where

d

=

ei(T f)

4 , (6)

where (a, x) is the (upper) incomplete gamma function [14], and thus Kc 2.366 (KdBc 3.74 dBc).

Appendix B

Derivation of equation (2)

Let us examine a short-time Fourier transform of a transmitted signal x(t) in a time window w(t) = 2T h(t)

which vanishes, along with all its derivatives, outside the interval [0, ]. We will let the window function w(t) represent the impulse response of an analog low-pass filter and be scaled so that

dn d

n [AT(

) h (t )] =

in (T f )n

d

ei(T f)

n

m=0

n m

A(nm)T(

) (1)m h(m) (t ) ,

(10)

where

n m

= n!

(nm)! m! is a binomial coefficient (n

choose m).

To analyze the relative contributions of the terms in(10), let us first consider the case where all derivatives of order smaller or equal to n - 1 of the window function w(t) are continuous, and all derivatives of the same order of the modulating signal AT(t) are finite, but the derivative of order n - 1 of AT(t) has a countable number of step discontinuities at {ti}:

i = lim

0

A(n1)T(ti + ) A(n1)T(ti )

0 dt w(t) = 1.

The short-time (windowed) Fourier transform X (t, )

of x(t) can be written as

X(t, ) =

d x() w(t ) ei

= w(t) [x(t)eit]= w(t) [x(t) cos(t)] i w(t) [x(t) sin(t)]

= I(t, ) + i Q (t, ),

(7)

= 0. (11)

From (11), it follows that A(n)T(t) has a piecewise con

tinuous component, as well as a singular component:

Nikitin EURASIP Journal on Advances in Signal Processing 2011, 2011:137 http://asp.eurasipjournals.com/content/2011/1/137

Page 8 of 10

A(n)T(t) =

ii(t ti)

+(piecewise continuous function of t) ,

(, )(t) =

dt

F [z(t) (, )(t)]

(12)

where (x) is the Dirac -function [15].

The significance of (12) lies in the sifting (sampling) property of the Dirac -function:

, (18)

where z(t) is the (complex-valued) input signal, (, ) (t) is the output, and are positive rate and time constant parameters, respectively, and

F(z) is a comparator function with the resolution (linear range) parameter a. For a particular differential over-limiter (DoL), the comparator function can be defined as

F(z) = z

|z|

F(|z|) =

dx (x x0) h (x) = h (x0) (13)

for a continuous h(x). Then, substitution of (12) into(10) leads to the following expression:

X(t, f ) = in

(T f )n

z

|z|

|z|

for |z| <

|z| otherwise

. (19)

When the condition |z(t)-(, )(t)| < is satisfied, the response of the DoL circuit equals that of an RC integrator with RC = . Otherwise, the output has a smaller absolute rate of change than the absolute rate of change of the output of the corresponding RC integrator. If a DoL circuit with sufficiently small is deployed early in the signal chain of a receiver channel affected by non-Gaussian impulsive noise, it can be shown that there exists such rate parameter that maximizes signal-to-noise ratio and improves the quality of the channel. The simplified example shown in Figure 6 illustrates this statement.

In Figure 6, the green lines in all panels show the incoming signal-plus-noise mixture, for both time (separately for the in-phase and the quadrature traces I/Q) and frequency domains. The incoming signal represents a communication signal with the total bandwidth of 5 MHz, affected by a bandlimited mixture of a thermal (Gaussian) and a white impulsive noises, with the total noise peakedness of 8.8 dBc. The signal-to-noise ratio in the baseband is 3 dB, and the bandwidth of the noise is an order of magnitude greater than the channel bandwidth.

The incoming signal is filtered by (i) an RC integrator with the time constant = 16 ns (black lines in the left-hand panels) and (ii) a DoL circuit with the same and appropriately chosen resolution parameter (black lines in the right-hand panels). Note that the RC integrator is just the DoL circuit in the limit of a large resolution parameter.

As can be seen in the left-hand panels, the RC filter does not affect the baseband signal-to-noise ratio, as it only reduces the power of the noise outside of the channel. Also, since the time constant is small, the noise remains impulsive (7 dBc), as can be seen in the upper panels on the left showing the in-phase/quadrature (I/Q) time domain traces. On the other hand, the DoL circuit (the right-hand panels) improves the signal-to-noise ratio in the baseband by 7.4 dB, effectively suppressing the impulsive component of the noise and reducing the

i

i h (t ti) ei(T f) t

(14)

+ ei(T f) (continuous function of

)

d

.

The second term in the square brackets is a Fourier transform of a continuous function, and it becomes negligible in comparison with the first term as the product T f increases. Thus, for the total power P (t, f) in a quadrature receiver,

Px(t, f ) = |X(t, f )|2

1

(T f )2n ii h (t ti)

jj h (t tj)

for T f 1,

(15)

which is Equation (2).

Appendix C

Discontinuities in continuous-phase modulationFor continuous-phase modulation (CPM), Equation (1) can be rewritten as

x(t) = AT(t) ei

ct =

A0ei(T fc)

t d aT()

eict, (16)

where fc is the frequency deviation. Then, the derivative of AT(t) is

A T(t) = i(T fc)AT(t)aT(t), (17)

and, if a(n2)T(t) contains discontinuities, so does A(n1)T(t), and the rest of the analysis of this article

holds.

Appendix D

Differential over-limiter (DoL)

A differential limiter can be defined as the following feedback circuit [13]:

Nikitin EURASIP Journal on Advances in Signal Processing 2011, 2011:137 http://asp.eurasipjournals.com/content/2011/1/137

Page 9 of 10

I/Q traces before/after RC

I/Q traces b efore/after D oL

quadrature

in-phase

t i m e ( s )

t i m e ( s )

P SD b efore/after RC

P SD b efore/after D oL

powerdensity(dB)

p e ak e d n e s 8 . 8 / 7 dBc

S N R 3/3 dB

n oise

b ase b an d

p e ak e d n e s 8 . 8 / 2 . 4

dBc

b ase b an d

S N R 3/10.4

dB

n oise

f r equ en cy ( M H z)

f r equ en cy ( M H z)

Figure 6 Impulsive noise mitigation by a differential over-limiter. The incoming signal affected by impulsive noise is shown by the green lines, and the outputs of the RC integrator (left-hand panels) and the DoL circuit (right-hand panels) are shown by the black lines. The detailed description of the figure is given in the text.

noise peakedness to 2.4 dBc. By comparing the black lines in the upper panels of the figure, for the RC and the DoL circuits, one can see how the DoL circuit removes the impulsive noise by trimming the outliers while following the narrower-bandwidth trend.

Differential limiters can also be viewed as feedback RC integrators where the time parameter ( = RC) is a variable that increases when the absolute value of the difference between the input and the feedback of the output exceeds the resolution parameter a. The output (, a) (t) of such a limiter can be described by

(, )(t) = dt

z(t) (, )(t) (, )(|z |)

, (20)

and the relationship between the variable time parameter

(, )(|z|) and the comparator function

F(|z|)

can be expressed as follows:

(, )(|z|) = |

z|

2otherwise . (22)

A detailed analysis of the DoL filter described by (18) and (19), or by (20) and (22), will be given elsewhere.

Endnotes

aIn general, if n is the order of a causal analog filter, then n - 1 is the order of the first discontinuous derivative of its impulse response. b One will encounter discontinuities in a derivative of some order in the modulating signal sooner or later, since any physical pulse shaping is implemented using causal filters of finite order. cEquation (2) will still accurately represent the total power in the quadrature receiver if the real (physical) modulating signal can be expressed as A(t) = (t) * AT(t), where the convolution kernel (t) is a low-pass filter of bandwidth much larger than f.

F(|z|)

1 . (21)

Thus, for the DoL circuit, the time parameter is given by

(, )(|z|) =

for |z| <

|z|

Nikitin EURASIP Journal on Advances in Signal Processing 2011, 2011:137 http://asp.eurasipjournals.com/content/2011/1/137

Page 10 of 10

AbbreviationsCPM: continuous-phase modulation; DoL: differential over-limiter; FIR: finite impulse response; I/Q: in-phase/quadrature; GPS: global positioning system; HSDPA: high speed downlink packet access; WCDMA: wideband code division multiple access; WiFi: wireless fidelity (a branded standard for wirelessly connecting electronic devices).

AcknowledgementsI express my sincere appreciation to RL Davidchack of the University of Leicester, UK, and to the reviewers of this manuscript for the valuable suggestions and critical comments, and to JB Lancaster of Horizon Analog Inc. (Lawrence KS, USA) for the experimental setup and the data used in Figures 1 through 3.

Author details

1Avatekh Inc., 900 Masachusetts Street, Suite 409, Lawrence, KS 66044, USA

2Horizon Analog Inc., Lawrence, KS, USA

Competing interestsThe author declares that he has no competing interests.

Received: 26 July 2011 Accepted: 21 December 2011 Published: 21 December 2011

References1. K Slattery, H Skinner, Platform Interference in Wireless Systems (Elsevier, Amsterdam, 2008)

2. F Leferink, F Silva, J Catrysse, S Batterman, V Beauvois, A Roch, Man-made noise in our living environments. Radio Sci Bull. 334, 4957 (2010)

3. X Yang, A Petropulu, Co-channel interference modeling and analysis in a Poisson field of interferers in wireless communications. IEEE Trans Signal Process. 51, 6476 (2003). doi:10.1109/TSP.2002.806591

4. AV Nikitin, On the impulsive nature of interchannel interference in digital communication systems, in Proceedings of IEEE Radio and Wireless Symposium, Phoenix, AZ, pp. 118121 (2011)

5. Abramowitz M, Stegun IA (eds.), Handbook of Mathematical Functions with Formulas, Graphs, and Mathematical Tables, 9th edn. (Dover, New York, 1972)

6. JG Proakis, DG Manolakis, Digital Signal Processing: Principles, Algorithms, and Applications, 4th edn. (Prentice Hall, New Jersey, 2006)

7. R Schaumann, ME Van Valkenburg, Design of Analog Filters (Oxford University Press, Oxford, 2001)

8. L Cohen, Time-Frequency Analysis (Prentice-Hall, Englewood, NJ, 1995)9. AV Nikitin, RL Davidchack, Signal analysis through analog representation. Proc R Soc Lond A. 459, 11711192 (2033)

10. AV Nikitin, RL Davidchack, Adaptive approximation of feedback rank filters for continuous signals. Signal Process. 84(4), 805811 (2004). doi:10.1016/j. sigpro.2004.01.001

11. AV Nikitin, RL Davidchack, Method and apparatus for analysis of variables. US Patents 7,133,568 (Nov. 7, 2006) and 7,242,808 (July 10, 2007)

12. AV Nikitin, Method and apparatus for real-time signal conditioning, processing, analysis, quantification, comparison, and control. US Patents 7,107,306 (Sep. 12, 2006), 7,418,469 (Aug. 26, 2008), and 7,617,270 (Nov. 10, 2009)

13. AV Nikitin, Method and apparatus for adaptive real-time signal conditioning and analysis. US Patent Application Publication 2011/0112784 (May 12, 2011)

14. IS Gradshteyn, IM Ryzhik, Table of Integrals, Series, and Products, 5th edn. (Academic Press, New York, 1994)

15. PAM Dirac, The Principles of Quantum Mechanics, 4th edn. (Oxford University Press, London, 1958)

doi:10.1186/1687-6180-2011-137Cite this article as: Nikitin: On the interchannel interference in digital communication systems, its impulsive nature, and its mitigation. EURASIP Journal on Advances in Signal Processing 2011 2011:137.

Submit your manuscript to a journal and benet from:

7 Convenient online submission7 Rigorous peer review7 Immediate publication on acceptance7 Open access: articles freely available onlihttp://www.springeropen.com/

Web End =ne 7 High visibility within the eld7 Retaining the copyright to your article

Submit your next manuscript at 7 http://www.springeropen.com/

Web End =springeropen.com