Microwave synthesizer using an on-chip Brillouin oscillator

Abstract

Low-phase-noise microwave oscillators are important to a wide range of subjects, including communications, radar and metrology. Photonic-based microwave-wave sources now provide record, close-to-carrier phase-noise performance, and compact sources using microcavities are available commercially. Photonics-based solutions address a challenging scaling problem in electronics, increasing attenuation with frequency. A second scaling challenge, however, is to maintain low phase noise in reduced form factor and even integrated systems. On this second front, there has been remarkable progress in the area of microcavity devices with large storage time (high optical quality factor). Here we report generation of highly coherent microwaves using a chip-based device that derives stability from high optical quality factor. The device has a record low electronic white-phase-noise floor for a microcavity-based oscillator and is used as the optical, voltage-controlled oscillator in the first demonstration of a photonic-based, microwave frequency synthesizer. The synthesizer performance is comparable to mid-range commercial devices.

ARTICLE

Received 20 Mar 2013 | Accepted 4 Jun 2013 | Published 28 Jun 2013

Low-phase-noise microwave oscillators are important to a wide range of subjects, including communications, radar and metrology. Photonic-based microwave-wave sources now provide record, close-to-carrier phase-noise performance, and compact sources using microcavities are available commercially. Photonics-based solutions address a challenging scaling problem in electronics, increasing attenuation with frequency. A second scaling challenge, however, is to maintain low phase noise in reduced form factor and even integrated systems. On this second front, there has been remarkable progress in the area of microcavity devices with large storage time (high optical quality factor). Here we report generation of highly coherent microwaves using a chip-based device that derives stability from high optical quality factor. The device has a record low electronic white-phase-noise oor for a microcavity-based oscillator and is used as the optical, voltage-controlled oscillator in the rst demonstration of a photonic-based, microwave frequency synthesizer. The synthesizer performance is comparable to mid-range commercial devices.

DOI: 10.1038/ncomms3097 OPEN

Microwave synthesizer using an on-chip Brillouin oscillator

Jiang Li1, Hansuek Lee1 & Kerry J. Vahala1

1 T. J. Watson Laboratory of Applied Physics, California Institute of Technology, Pasadena, California 91125, USA. Correspondence and requests for materials should be addressed to K.J.V. (email: mailto:[email protected]

Web End [email protected] ).

NATURE COMMUNICATIONS | 4:2097 | DOI: 10.1038/ncomms3097 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications 1

& 2013 Macmillan Publishers Limited. All rights reserved.

ARTICLE NATURE COMMUNICATIONS | DOI: 10.1038/ncomms3097

a

The generation of low-phase-noise radio, microwave and optical signals relies upon resonant devices that feature large storage times or equivalently high-Q factors1,2. Maintaining

large storage time, in compact or integrated circuits, becomes increasingly challenging with decreasing size and increasing frequency3,4. These two scaling laws of performance create challenges for compact or integrated microwave and millimeter-wave sources, wherein performance (in terms of phase noise at a given offset frequency) steadily degrades with increasing oscillation frequency4. As a result, state-of-the-art microwave oscillators are larger, discrete devices based on dielectric resonators5. The introduction of optical bre for long-distance communication had a positive impact on the frequency scaling side of this problem. First, the distribution of microwaves over optical bre has led to remarkable progress on transfer of low-phase-noise microwaves onto optical carrier waves3,6. Second, bre delay lines provided a way to create long storage time with no frequency-dependent attenuation in hybrid optoelectronic oscillators7. These high-performance optoelectronic oscillators represented a paradigm shift in the generation of microwaves and were followed by optical resonator-based versions that employed an optical microcavity to achieve the requisite oscillator storage time8,9. Generally, the ability to achieve long storage times in compact, high-Q resonators has experienced a major leap forward during this same period1015.

On another front, both bre and optical resonators have also been applied to create microwaves by heterodyne of coherent laser lines16,17. In this case, co-oscillation occurs within the same cavity so that a high level of common-mode noise suppression leads to good performance microwave generation16,18. Sideband injection locking in a master-slave laser conguration has also been applied to enable broadband multiplication of a supplied electronic microwave signal19. A remarkable, recent advance has been the introduction of optical dividers in the form of frequency combs to create record low close-to-carrier phase-noise microwave signal sources20. Frequency combs have previously been applied to stabilize optical carrier frequencies for distribution of microwaves over optical bre2123, however, in this new approach an optical signal serves as the root for the ultra-high-stability microwave signal itself. Although the technique is complex, emerging technologies like frequency microcombs24,25 and compact reference cavities2629 could one day lead to chip-based photonic microwave sources that exceed the performance of the best electronic sources. In a related development, microcavity-based microcombs and parametric oscillators are providing a new way to synthesize microwaves directly3035. Although the performance is well off from the optical divider approach, the method is less complex.

In this work, we report the application of cascaded Brillouin oscillation to microwave frequency synthesis at a level comparable to mid-range commercial, all-electrical synthesizers. Although bre-based Brillouin lasers have been studied for microwave generation3640, the present device is the rst chip-based Brillouin microwave source. Moreover, the device has a record low-white-phase-noise oor ( 160 dBc Hz 1) for any microcavity-based

microwave source (even including non-Brillouin-based methods). It can also generate coherent microwave power in excess of 1 mW without any optical or radio frequency (RF) amplication, a signicant simplication as it eliminates the need for microwave amplication stages after the photodetector. Moreover, being chip-based devices, the current sources offer integration opportunities for control and additional functions.

ResultsMicrowave generation using chip-based Brillouin lasers. An ultra-high-Q planar silica-on-silicon disk resonator15 is used for

cascaded Brillouin oscillation and microwave generation. Microcavity-based Brillouin lasers have only recently been demonstrated4143. The present devices are silicon-chip based and they feature very high coherence and high quantum efciency15,44. Both high-power and low-phase-noise microwave generation from the disk resonator are achieved by cascaded stimulated Brillouin lasing and subsequent photomixing of pairs of Brillouin laser as illustrated in Fig. 1a. A narrow-linewidth bre laser (effective linewidth 1 kHz) is used as the pump laser and is coupled to the disk resonator (see photomicrograph in Fig. 1b) through a taper bre technique45. The size of the disk resonator (B6 mm) is carefully designed such that the free spectral range of the cavity matches the Brillouin gain shift15,44. Once the coupled pump power reaches the stimulated Brillouin threshold, the rst-order Stokes wave is excited in the backward direction and is routed through a bre circulator to an optical spectral analyser, a monitor photodetector (bandwidth 125 MHz) and a fast photodetector (bandwidth 50 GHz). Further increase of the pump power leads to cascaded Brillouin lasing, for example, 9th-order Stokes has been demonstrated in our previous work44. These cascaded lines feature SchawlowTownes noise o0.1 Hz2 Hz 1 (refs 15,44) and low technical frequency noise.

As a result, they are suitable for high-stability microwave synthesis by photomixing. Fine control of this frequency is possible by adjustment of the pump frequency using acousto-optic modulation. The detected Brillouin laser can therefore function as the voltage-controlled oscillator (VCO) in a microwave synthesizer as illustrated in Fig. 1c.

1st

Pump

b

3rd 2nd

Disk

c

Laser

AOM

Disk

Vtune

PD

Low-frequency reference oscillation

Loop filter

RF out

detector

1/N

Figure 1 | Explanation of microwave synthesizer using chip-based Brillouin laser. (a) A Brillouin microwave oscillator showing pump (blue) and second Stokes (orange) waves, and the rst (green) and third(red) Stokes waves incident on the detector for microwave generation. (b) Photograph of an B6 mm ultra-high-Q planar silica disk resonator on a silicon chip. Scale bar, 1 mm. (c) Block diagram for a closed-loop Brillouin microwave oscillator. The open-loop Brillouin microwave oscillator (shown in the upper dashed box) functions as a voltage-controlled photonic oscillator. All hardware in the upper dashed box replaces an electrical VCO in a conventional electrical synthesizer. Components in the upper box include a pump laser, acousto-optic modulator (AOM), circulator, high-speed detector and ultra-high-Q disk resonator. PD, photodetector.

2 NATURE COMMUNICATIONS | 4:2097 | DOI: 10.1038/ncomms3097 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications

& 2013 Macmillan Publishers Limited. All rights reserved.

NATURE COMMUNICATIONS | DOI: 10.1038/ncomms3097 ARTICLE

where P is output power of the Brillouin laser, t (tex) is the total

(external) cavity photon life time, c is the speed of light, n is the refractive index of silica and Va is the sound velocity in silica. This equation gives the limit of the SchawlowTownes noise formula44 when the number of thermal quanta of the Brillouin phonons is far greater than unity, which is the case for measurements taken at room temperature (thermal quanta 569). It is important to

note that the SchawlowTownes noise is independent of both the pump frequency and the Brillouin frequency. As a result, at an equivalent power level, the phase-noise levels measured in Fig. 2 would be expected if the pump frequency was higher resulting in a higher-frequency Brillouin shift. For the calculation of the ShawlowTownes noise, measured cavity t of t 28 ns and

tex

34 ns are used (that is, no free parameters are used), and L(f) 10logSIff =2. Here SIff is the one-sided power spectral

density of phase noise and is related to the two-sided power spectral density of frequency noise SIInf as: SIff 2SIInf f

2

20

80

L(f) at 100 kHz (dBc Hz1)

0

85

Measured Calculated

90

20

95

40

100

L(f) (dBc Hz1 )

60

105 20 15 10 5 0 5

3rd Stokes power (dBm)

80

100

120

140

160 101 102 103 104 105 106 107 108

Figure 2 | Power dependence of microwave phase noise. The microwave signal is produced by photomixing the rst and third Stokes lines on a high-speed detector. The output optical power of the third Stokes line is increasing from top to bottom curves ( 16.5, 10.2, 8.2, 4.5, 1.4

and 1.2 dBm, respectively). The phase noise shows 1/f2 dependences for ve decades from 200 Hz to 20 MHz. The dashed lines are 1/f2 ts to the measured phase-noise spectra. Inset: plot showing inverse power dependence of the phase noise of the Brillouin microwave signal(100 kHz offset frequency) on the optical power of the third Stokes line. Circles, measured values; dashed line, calculated values based uponthe SchawlowTownes formula.

The Brillouin shift in the silica disk cavity is around 10.8 GHz (ref. 44), so that microwave generation from around 10.8 to86 GHz is feasible in the present device by photomixing pairs of the cascaded Brillouin lines. We have focused on the generation of K-band (B21.521.8 GHz) microwave signals by photomixing the rst and third Stokes lines. Operationally, these lines feature high coherence with very low SchawlowTownes noise and technical noise; they also provide high-power levels and propagate in the same direction. It is important to note that besides the common-mode noise suppression that occurs upon photomixing because the Brillouin laser lines share a common laser cavity, combinations of laser lines that share the same optical path (that is, oddodd and eveneven Stokes pairs) also enable cancellation of any optical-path length jitter effects.

Phase noise of optical VCO. To measure the phase noise of the K-band microwave signal, a phase-noise analyser (Rohde-Schwartz FSUP Signal Source Analyzer) is used. Figure 2 shows the single-sideband phase noise (L(f)) of a 21.7-GHz signal generated using the rst and third Stokes laser lines for a series of output optical power levels of the 3rd Stokes ( 16.5, 10.2, 8.2, 4.5, 1.4 and 1.2 dBm from upper to lower curves).

Signicantly, the phase noise of this signal has 1/f2 dependence over ve decades (200 Hz to 20 MHz), which corresponds to white frequency noise. Moreover, this 1/f2 noise has an inverse dependence on the third Stokes laser line power as shown in the inset to Fig. 2 (phase noise is measured at 100 kHz frequency offset, and power is varied by changing the pump power). The inset of Fig. 2 also shows a calculated phase noise based on the SchawlowTownes frequency noise of the third Stokes line power. For a Brillouin laser, the two-sided SchawlowTownes frequency noise44 can be rewritten as:

SSTnf

kT 8p2ttexP

.

Because the output optical power of the rst Stokes line varies over 2.55.0 dBm from the upper to lower measurement curves (that is, power levels much greater than for the third Stokes wave), the SchawlowTownes noise of the rst Stokes line is not expected to be a signicant component of noise in the photomix-generated carrier wave. Indeed, the good agreement between the measurement values and calculation in the inset of Fig. 2 shows that the phase noise of the Brillouin microwave signal is mainly contributed by the SchawlowTownes noise of the third Stokes line. As a general comment relevant to the discussion of phase noise in the introduction, the results in Fig. 2 conrm that the very high-Q factor of the Brillouin laser (high storage time) leads to the low-microwave phase noise upon photomixing of the Stokes laser lines. Ultimately, the cascade process sets the limit of phase noise in these devices (see Supplementary Note 1). Finally, at low-offset frequencies in Fig. 2, the phase noise exhibits a non-SchawlowTownes component. Although Brillouin lasers suppress technical phase noise from the pump44,41, it is possible that this noise is contributed by the pump. It is also possible that this noise is environmental related. The closed-loop control described in the next section suppresses this noise.

Phase-locked operation of oscillator. The Brillouin microwave oscillator can be operated in two distinct ways: open loop (no feedback control) and closed loop (phase-lock-loop control). In open-loop operation, the rst and third Stokes lines from the resonator are directly photomixed on a fast photodetector with no other control. This is the method used for the spectra in Fig. 2. Alternatively, the centre frequency of the free-running Brillouin microwave oscillator can be nely varied in the range of 100 s kHz to a few MHz, by adjusting the pump laser frequency either through a piezo control of the pump laser cavity or with an external acousto-optic modulator. Thus, the Brillouin oscillator constitutes a VCO, and the device can be congured into a phase-lock-loop control design (that is, closed-loop operation). Phase-lock-loop control of optically generated microwave tones has been previously accomplished by reference to a high-performance microwave reference4648. In these earlier works, the objective was to use the the high-stability microwave electrical reference to stabilize the optical generated tone. In the present case, the original microwave tone from the open-loop stimulated Brillouin scattering (SBS) oscillator is already of sufcient stability at shorter times (higher offset frequencies), so that the phase-lock-loop (PLL) is used only to obtain long-term stability. Moreover, the loop control does not use another microwave oscillator to achieve stability, but rather a low-frequency quartz oscillator via electrical frequency division. Indeed, the divider used here not only allows

Offset frequency (Hz)

c2nVa 1

NATURE COMMUNICATIONS | 4:2097 | DOI: 10.1038/ncomms3097 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications 3

& 2013 Macmillan Publishers Limited. All rights reserved.

ARTICLE NATURE COMMUNICATIONS | DOI: 10.1038/ncomms3097

a Pump Pump 2nd

b

20

0

Open loop 21.7 GHzClosed loop 21.7 GHz Reference scaled to 21.7 GHz

AOM

PD1

20

Pump laser

1st

40

L(f) (dBc Hz1 )

SBS disk

3rd

60

f/N

Splitter

80

wave output

Ref In

100

PD2

Amp

PNA

ADEV

10 MHz clk

120

f/N

Divider

OSA

140

160 101 102 103 104 105 106 107 108

Ref In

Low frequency reference oscillator

Servo

Offset frequency (Hz)

c 1st 3rd

0

d

0

10

10

RBW 100 Hz

Optical spectrum (dBm)

20

20

30

30

40

40

RF power (dBm)

50

50

60

70

60

80

70

90

80 1,549.4 1,549.6 1,549.8 1,550 1,550.2

100 100 50 0 50 100

Wavelength (nm)

kHz + 21.7 GHz

e f

20

106

10

RBW 1 Hz

0

108

10

RF power (dBm)

1010

Open loop Closed loop Counter limit

20

30

ADEV

40

1012

50

60

1014

70

80

16

100 50 0 50 100

10 103 102 101 100 101 102

Hz + 21.7 GHz

[afii9848] (s)

Figure 3 | Performance of the synthesizer for both open and closed-loop operation. (a) Experimental schematic for the closed-loop Brillouin microwave oscillator. AOM, acouto-optic modulator; f/N, frequency divider; PD, photodetector; OSA, optical spectrum analyzer. A mutual time base is shared between the phase-noise analyser (PNA), low-frequency reference oscillator and the ADEV. (b) Open-loop (red curve) and closed-loop (blue curve) single-sideband phase noise of the Brillouin oscillator at 21.7 GHz. The green dashed line is the phase noise of the reference oscillator scaled up to 21.7 GHz. (c) Optical spectrum of the 1st-Stokes and 3rd-Stokes laser emission lines. The pump wave is also visible, but is weak on account of propagation opposite to the direction of the 1st and 3rd Stokes lines. Also visible is the 5th Stokes line in the spectrum as well as the rst anti-Stokes wave. (d) RF spectrum of an open-loop Brillouin oscillator at 21.7 GHz. The span is 200 kHz and the resolution bandwidth (RBW) is 100 Hz. (e) RF spectrum of a closed-loop Brillouin oscillator at 21.7 GHz. The span is reduced to 200 Hz and the RBW is 1 Hz. (f) Allan deviation (ADEV) of the Brillouin microwave oscillator. Circle markers represent the open-loop operation, square markers represent the residual Allan deviation for the close-loop operation and the diamond markers give the counter limit.

stabilization using a low-frequency reference oscillator but also converts the SBS microwave signal into nearly any microwave signal frequency o21.8 GHz. As a result, this device constitutes a microwave synthesizer with performance comparable to good commercial electrical synthesizers. The essential elements of the

SBS microwave synthesizer are shown in the experimental schematic of Fig. 3a. The synthesizer is analysed by a phase-noise analyser and an Allan deviation tester (ADEV), and a mutual time base is shared between the frequency reference, phase-noise analyser and the ADEV.

4 NATURE COMMUNICATIONS | 4:2097 | DOI: 10.1038/ncomms3097 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications

& 2013 Macmillan Publishers Limited. All rights reserved.

NATURE COMMUNICATIONS | DOI: 10.1038/ncomms3097 ARTICLE

a

20

b

0.2

2.7 GHz

Closed-loop 21.7 GHz

Div by 32 = 678 MHz

Div by 256 = 85 MHz Div by 512 = 42 MHz Div by 1024 = 21 MHz Div by 2048 = 11 MHz

0.1

40

0

0.1

60

0.2 1 0 1 2 3

80

0.2

Voltage (a.u.)

1.35 GHz

L(f) (dBc Hz1 )

0.1

100

0

0.1

120

0.2 2 1 0 1 2

140

0.5

678 MHz

160

0

180 101 102 103 104 105 106 107 108

0.5 4 2 0 2 4

Offset frequency (Hz)

t (ns)

Figure 4 | RF frequency synthesis by the K-band low-noise Brillouin microwave oscillator. (a) Phase noise of a series of RF frequencies generated by frequency division (Div) in the synthesizer. (b) Typical sine-wave, time-domain traces of the synthesizer output at 2.7 GHz, 1.35 GHz and 678 MHz (from top to bottom). All frequencies lower than the base oscillator frequency of 21.7 GHz are possible, and the traces selected here were limited by the bandwidth of oscilloscope (4 GHz).

10 103 102 101 100 101 102

109

1010

1011

1012

ADEV

1013

1014

Out-of-loop

In-loop

Reference

1015

16

[afii9848] (s)

Figure 5 | Allan deviation measurements. The Brillouin microwave oscillator (21.7 GHz) is phase locked to an ultra-low-noise OCXO at400 MHz as reference. The blue square markers are the residual Allan deviation (ADEV) of the Brillouin microwave oscillator with regard to the reference OCXO. The green diamond markers are the out-of-loop Allan deviation, measured against a second low-noise OCXO at 10 MHz. The red circle markers are the Allan deviation of the reference OCXO at 400 MHz measured against the second OCXO at 10 MHz.

The optical spectrum of the generated Stokes lines in the back-propagating direction is shown in Fig. 3c and includes the rst and third Stokes lines that are used to generate the microwave tone of the present work. The incident optical power levels of the rst and third Stokes lines on the high-speed photodiode are 3.7 and1.7 mW, respectively (the coupled optical pump power to the microresonator was 31 mW). For comparison purposes, the open-and closed-loop phase-noise spectra are presented in Fig. 3b together with the scaled-up phase noise of the low-frequency reference oscillator. Phase-noise levels (open loop) of

90 dBc Hz 1 at 10 kHz offset and 110 dBc Hz 1 at

100 kHz are obtained for the 21.7 GHz carrier. The measured white-phase-noise oor of the oscillator ( 156 dBc Hz 1

4100 MHz) is a record for a microcavity-based microwave source by several orders of magnitude9,30,35. The calculated shot noise oor is 158 dBc Hz 1 for the 21.7 GHz carrier, with 2.2 mA average

photocurrent and a generated RF power of 15.5 dBm, and is in

good agreement with the measured result. Using another device, both a higher RF power of 2.9 dBm (1.9 mW, no optical or RF amplication) and yet lower white-phase-noise oor of 160 dBc/

Hz were obtained. These results are within 19 dB of the very lowest white-phase-noise oors recently demonstrated using high-performance frequency combs and high-power photodiodes49. Further details on this measurement as well as the power calculations themselves are provided in the Supplementary Note 2.

For closed-loop operation, an integer frequency divider (1/32) is used to divide the free-running microwave carrier to 678 MHz for phase comparision with a low-frequency reference oscillator at 678 MHz. The blue curve in Fig. 3b shows the phase noise of the closed-loop Brillouin oscillator. The close-to-carrier phase noise is now greatly reduced. The phase noise of the frequency reference is also shown in Fig. 3b as the green dashed line. A factor of 20

log32 30 dB has been added to this line to account for phase-noise

scaling with frequency, and thereby enable comparison with the phase noise of the closed-loop oscillator. As expected, for low-offset frequencies, the closed-loop oscillator tracks the scaled-up reference noise. The corresponding RF spectra for the open-loop (span 200 kHz and resolution bandwidth 100 Hz) and closed-loop (span 200 Hz and resolution bandwidth 1 Hz) oscillators are given in Fig. 3d,e, respectively. To characterize the long-term frequency stability of the Brillouin oscillator, ADEV measurements were carried out for open-loop and closed-loop operation using gate times from 1 to 400 s. The measurement results (normalized to the Brillouin oscillator frequency) are shown in Fig. 3f. For these measurements, a sub-harmonic (1/256) at 84.6 MHz of the Brillouin oscillator is measured, as the maximum input frequency of the ADEV is 400 MHz. It can be seen that the long-term drift of the open-loop VCO is greatly suppressed. More than 80 dB reduction of the ADEV (with respect to the 10-MHz mutual time base) is obtained at 400 s gate time. Also, a residual Allan Deviation of 5 10 13 is achieved at 1 s. Overall, the closed-loop

NATURE COMMUNICATIONS | 4:2097 | DOI: 10.1038/ncomms3097 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications 5

& 2013 Macmillan Publishers Limited. All rights reserved.

ARTICLE NATURE COMMUNICATIONS | DOI: 10.1038/ncomms3097

Brillouin oscillator has low phase noise at both close-to-carrier and high-offset frequencies. In fact, the phase-noise level demonstrated here is between a mid-range (Agilent N5183A MXG, phase noise of 97 dBc/Hz at 100 kHz offset for 20 GHz carrier; Data Sheet,

Literature number 5989-7572EN) and high-performance (Agilent E8257D PSG, phase noise of 111 dBc/Hz at 100 kHz offset for

20 GHz carrier; Data Sheet, Literature number 5989-0698EN) commercial electrical microwave synthesizers.

Frequency synthesizer operation. RF frequency synthesis derived from the low-noise closed-loop Brillouin oscillator was also demonstrated. This is done by using a (fractional or integer) frequency divider to divide the closed-loop Brillouin oscillator at21.7 GHz to different frequencies. A series of the phase-noise spectra using different division ratios (f/N; N 32, 256, 512, 1,024

and 2,048) is shown in Fig. 4a. Generally, the single-sideband phase noise L(f) will drop 20logN dB upon frequency division. Thus, RF frequency synthesis at arbitrary frequencies up to22 GHz is possible based on the low-noise K-band Brillouin oscillator. The time-domain traces are shown in Fig. 4b for2.7 GHz, 1.35 GHz and 678 MHz, measured using an oscilloscope with 4 GHz bandwidth.

Out-of-loop Allan deviation. Finally, closed-loop operation of the Brillouin oscillator was also possible by referencing to a xed-frequency, ultra-low-noise oven-controlled crystal oscillator (OCXO) at 400 MHz. Figure 5 shows the Allan deviation measurements normalized to the Brillouin oscillator frequency. The blue square markers are the residual ADEV of the Brillouin microwave oscillator with regard to the reference OCXO. For a more rigorous measurement, we also measure the out-of-loop Allan deviation of the closed-loop VCO using a second independent ultra-low-noise OCXO (10 MHz). The green diamond markers are the out-of-loop ADEV and the red circle markers are the ADEV of the reference OCXO at 400 MHz measured against the second OCXO at 10 MHz. The out-of-loop ADEV tracks the 400 MHz reference for t40.03 s. Thus, the out-of-loop ADEV is reference-limited, and an out-of-loop ADEV level of 5 10 12 at

1 s gate time is demonstrated.

DiscussionIn this work, we have demonstrated a microwave synthesizer with commercial-level frequency stability using a compact, on-chip Brillouin laser VCO. The combined demonstrations show that the Brillouin VCO can operate as a direct replacement for conventional electronic VCO devices. Signicantly, the phase noise of the Brillouin VCO does not degrade with increasing frequency as compared with electronic devices. This is because the phase noise contributed by the underlying Stokes lines (assuming constant power in each line) is not sensitive to order or to pump frequency. Also, by operating the Brillouin at shorter pump wavelengths or by operating on higher-order Stokes lines, the base frequency of the synthesizer can be readily boosted. For example, by operation with a green pump (doubled yttrium aluminum garnet laser), the base frequency would be boosted to beyond 60 GHz using the same Stokes 1 to Stokes 3 photomixing conguration demonstrated here (again with no degradation in phase-noise performance). Also, by operation on the 15 or 17 Stokes combinations, millimeter-wave generation well beyond 100 GHz is feasible. Likewise, electronic dividers have been demonstrated to these frequencies50, thereby making the possibility of high-performance millimeter-wave synthesizers possible using this approach. It is important to note that such millimeter-wave synthesizers would be predicted to produce X-band signals with signicantly lower phase noise than what has even been demonstrated here. This is because the divider

process quadratically improves the phase noise. For example, by only maintaining the SchawlowTownes noise at shorter pump wavelengths, the predicted X-band (B10 GHz) phase-noise level would be 130 dBc Hz 1 at 100 kHz offset upon division of a 90-

GHz SBS-generated base frequency. Ultimately, the current limit to phase noise in these devices is the onset of cascade to higher-order Stokes lines. If this process could be forestalled through, for example, judicious cavity dispersion control, then much lower phase-noise levels than what has been demonstrated here are possible.

References

1. Leeson, D. B. A simple model of feedback oscillator noise spectrum. Proc. IEEE 54, 329330 (1966).

2. Yariv, A. Quantum Electronics (John Wiley & Sons, 1989).3. Seeds, A. J. & Williams, K. J. Microwave photonics. J. Lightw. Technol. 24,

46284641 (2006).

4. Khanna, A. Microwave oscillators: the state of the technology. Microwave J. 49, 2228 (2006).

5. Howe, D. & Hati, A. Low-noise x-band oscillator and amplier technologies: comparison and status. IEEE Int. Freq. Control Symp. 481487 (2005).

6. Capmany, J. & Novak, D. Microwave photonics combines two worlds. Nat. Photon 1, 319330 (2007).

7. Yao, X. S. & Maleki, L. Optoelectronic microwave oscillator. J. Opt. Soc. Am. B 13, 17251735 (1996).

8. Maleki, L. Sources: the optoelectronic oscillator. Nat. Photon 5, 728730 (2011).9. Savchenkov, A. et al. Voltage-controlled photonic oscillator. Opt. Lett. 5, 15721574 (2010).

10. Gorodetsky, M. L., Savchenkov, A. A. & Ilchenko, V. S. Ultimate Q of optical microsphere resonators. Opt. Lett. 21, 453455 (1996).

11. Vernooy, D. W., Ilchenko, V. S., Mabuchi, H., Streed, E. W. & Kimble, H. J. High-Q measurements of fused-silica microspheres in the near infrared. Opt. Lett. 23, 247249 (1998).

12. Armani, D., Kippenberg, T., Spillane, S. & Vahala, K. Ultra-high-Q toroid microcavity on a chip. Nature 421, 925928 (2003).

13. Savchenkov, A. A., Ilchenko, V. S., Matsko, A. B. & Maleki, L. Kilohertz optical resonances in dielectric crystal cavities. Phys. Rev. A 70, 051804 (2004).

14. Grudinin, I. S., Ilchenko, V. S. & Maleki, L. Ultrahigh optical Q factors of crystalline resonators in the linear regime. Phys. Rev. A 74, 063806 (2006).

15. Lee, H. et al. Chemically etched ultrahigh-Q wedge-resonator on a silicon chip. Nat. Photon 6, 369373 (2012).

16. Pillet, G. et al. Dual-frequency laser at 1.5 mm for optical distribution and generation of high-purity microwave signals. J. Lightw. Technol. 26, 27642773 (2008).

17. Maxin, J. et al. Dual-frequency distributed feedback bre laser for microwave signals generation. Electron. Lett. 47, 816818 (2011).

18. Drever, R. et al. Laser phase and frequency stabilization using an optical resonator. Appl. Phys. B 31, 97105 (1983).

19. Schneider, G. J., Murakowski, J. A., Schuetz, C. A., Shi, S. & Prather, D. W. Radiofrequency signal-generation system with over seven octaves of continuous tuning. Nat. Photon 7, 118122 (2013).

20. Fortier, T. et al. Generation of ultrastable microwaves via optical frequency division. Nat. Photon 5, 425429 (2011).

21. Fukushima, S., Silva, C., Muramoto, Y. & Seeds, A. 10 to 110 GHz tunable opto-electronic frequency synthesis using optical frequency comb generator and unitravelling-carrier photodiode. Electron. Lett. 37, 780781 (2001).

22. McFerran, J. J. et al. Low-noise synthesis of microwave signals from an optical source. Electron. Lett. 41, 650651 (2005).

23. Swann, W. C., Baumann, E., Giorgetta, F. R. & Newbury, N. R. Microwave generation with low residual phase noise from a femtosecond ber laser with an intracavity electro-optic modulator. Opt. Express 19, 2438724395 (2011).

24. DelHaye, P. et al. Optical frequency comb generation from a monolithic microresonator. Nature 450, 12141217 (2007).

25. Kippenberg, T., Holzwarth, R. & Diddams, S. Microresonator-based optical frequency combs. Science 332, 555559 (2011).

26. Alnis, J., Schliesser, A., Wang, C., Hofer, J., Kippenberg, T. & Hansch, T. Thermal-noise-limited crystalline whispering-gallery-mode resonator for laser stabilization. Phys. Rev. A 84, 011804 (2011).

27. Young, B., Cruz, F., Itano, W. M. & Bergquist, J. Visible lasers with subhertz linewidths. Phys. Rev. Lett. 82, 37993802 (1999).

28. Savchenkov, A. A., Matsko, A. B., Ilchenko, V. S., Yu, N. & Maleki, L. Whispering-gallery-mode resonators as frequency references. II. stabilization.J. Opt. Soc. Am. B 24, 29882997 (2007).29. Yu, N., Baumgartel, L. M., Chembo, Y., Grudinin, I. S., Strekalov, D. V. & Thompson, R. J. Whispering-gallery-mode resonators for miniature optical clocks. SPIE Proc. 82360P82360P (2012).

6 NATURE COMMUNICATIONS | 4:2097 | DOI: 10.1038/ncomms3097 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications

& 2013 Macmillan Publishers Limited. All rights reserved.

NATURE COMMUNICATIONS | DOI: 10.1038/ncomms3097 ARTICLE

30. Savchenkov, A. et al. Kerr combs with selectable central frequency. Nat. Photon 5, 293296 (2011).

31. Papp, S. B. & Diddams, S. A. Spectral and temporal characterization of a fused-quartz-microresonator optical frequency comb. Phys. Rev. A 84, 053833 (2011).

32. Li, J., Lee, H., Chen, T. & Vahala, K. J. Low-pump-power, low-phase-noise, and microwave to millimeter-wave repetition rate operation in microcombs. Phys. Rev. Lett. 109, 233901 (2012).

33. Papp, S. B., DelHaye, P. & Diddams, S. A. Mechanical control of a microrodresonator optical frequency comb. Phys. Optics. Preprint at http://arxiv.org/abs/ 1205.4272 (2012).

34. DelHaye, P., Papp, S. B. & Diddams, S. A. Hybrid electro-optically modulated microcombs. Phys. Rev. Lett. 109, 263901 (2012).

35. Savchenkov, A. et al. Miniature optical atomic clock: Stabilization of a kerr comb oscillator. Phys. Optics. Preprint at http://arxiv.org/abs/1301.3198 (2013).

36. Yao, X. S. High-quality microwave signal generation by use of brillouin scattering in optical bers. Opt. Lett. 22, 13291331 (1997).

37. Schneider, T., Junker, M. & Lauterbach, K.-U. Theoretical and experimental investigation of brillouin scattering for the generation of millimeter waves.J. Opt. Soc. Am. B 23, 10121019 (2006).38. Geng, J., Staines, S. & Jiang, S. Dual-frequency brillouin ber laser for optical generation of tunable low-noise radio frequency/microwave frequency. Opt. Lett 33, 1618 (2008).

39. Gross, M. C. et al. Tunable millimeter-wave frequency synthesis up to 100 GHz by dual-wavelength brillouin ber laser. Opt. Express 18, 1332113330 (2010).

40. Callahan, P. T., Gross, M. C. & Dennis, M. L. Frequency-independent phase noise in a dual-wavelength brillouin ber laser. IEEE J. Quantum Electron. 47, 11421150 (2011).

41. Grudinin, I. S., Matsko, A. B. & Maleki, L. Brillouin lasing with a CaF2 whispering gallery mode resonator. Phys. Rev. Lett. 102, 043902 (2009).

42. Tomes, M. & Carmon, T. Photonic micro-electromechanical systems vibrating at X-band (11-GHz) rates. Phys. Rev. Lett. 102, 113601 (2009).

43. Pant, R. et al. On-chip stimulated Brillouin scattering. Opt. Express 19, 82858290 (2011).

44. Li, J., Lee, H., Chen, T. & Vahala, K. J. Characterization of a high coherence, brillouin microcavity laser on silicon. Opt. Express 20, 2017020180 (2012).

45. Cai, M., Painter, O. & Vahala, K. J. Observation of critical coupling in a ber taper to a silica-microsphere whispering-gallery mode system. Phys. Rev. Lett. 85, 7477 (2000).

46. Langley, L. et al. Packaged semiconductor laser optical phase-locked loop (opll) for photonic generation, processing and transmission of microwave signals. IEEE Trans. Microw. Theory 47, 12571264 (1999).

47. Bordonalli, A., Walton, C., Seeds, A., Seeds, A. & Seeds, A. J. High-performance phase locking of wide linewidth semiconductor lasers by combined use of optical injection locking and optical phase-lock loop. J. Lightwave Technol. 17, 328 (1999).

48. Alouini, M. et al. Offset phase locking of Er, Yb: glass laser eigenstates for rf photonics applications. IEEE Photon. Technol. Lett. 13, 367369 (2001).

49. Quinlan, F. et al. Exploiting shot noise correlations in the photodetection of ultrashort optical pulse trains. Nat. Photon 7, 290293 (2013).

50. Rylyakov, A. & Zwick, T. 96-GHz static frequency divider in SiGe bipolar technology. IEEE J. Solid-State Circ. 39, 17121715 (2004).

Acknowledgements

We would like to thank Dave Howe, Scott Diddams, Scott Papp (NIST, Boulder CO) and Lute Maleki (OEWaves) for their helpful discussions and comments on this manuscript. This work was sponsored by the DARPA Orchid program. Wealso acknowledge the support from the Institute for Quantum Information and Matter, an NSF Physics Frontiers Center with support of the Gordon and Betty Moore Foundation, and the Kavli Nanoscience Institute.

Author contributions

J.L. and K.J.V. conceived and designed the experiment. J.L. performed the measurements and data analysis with supervision by K.J.V. H.L. fabricated the devices, with assistance from J.L. All authors helped to write the paper.

Additional information

Supplementary Information accompanies this paper at http://www.nature.com/naturecommunications

Web End =http://www.nature.com/ http://www.nature.com/naturecommunications

Web End =naturecommunications

Competing nancial interests: The authors declare no competing nancial interests.

Reprints and permission information is available online at http://npg.nature.com/reprintsandpermissions/

Web End =http://npg.nature.com/ http://npg.nature.com/reprintsandpermissions/

Web End =reprintsandpermissions/

How to cite this article: Li, J. et al. Microwave synthesizer using an on-chip Brillouin oscillator. Nat. Commun. 4:2097 doi: 10.1038/ncomms3097 (2013).

This article is licensed under a Creative Commons Attribution 3.0 Unported Licence. To view a copy of this licence visit http://creativecommons.org/licenses/by/3.0/

Web End =http:// http://creativecommons.org/licenses/by/3.0/

Web End =creativecommons.org/licenses/by/3.0/ .

NATURE COMMUNICATIONS | 4:2097 | DOI: 10.1038/ncomms3097 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications 7

& 2013 Macmillan Publishers Limited. All rights reserved.