Ultra-high aspect ratio high-resolution nanofabrication for hard X-ray diffractive optics

Abstract

Although diffractive optics have played a major role in nanoscale soft X-ray imaging, high-resolution and high-efficiency diffractive optics have largely been unavailable for hard X-rays where many scientific, technological and biomedical applications exist. This is owing to the long-standing challenge of fabricating ultra-high aspect ratio high-resolution dense nanostructures. Here we report significant progress in ultra-high aspect ratio nanofabrication of high-resolution, dense silicon nanostructures using vertical directionality controlled metal-assisted chemical etching. The resulting structures have very smooth sidewalls and can be used to pattern arbitrary features, not limited to linear or circular. We focus on the application of X-ray zone plate fabrication for high-efficiency, high-resolution diffractive optics, and demonstrate the process with linear, circular, and spiral zone plates. X-ray measurements demonstrate high efficiency in the critical outer layers. This method has broad applications including patterning for thermoelectric materials, battery anodes and sensors among others.

ARTICLE

Received 17 Jan 2014 | Accepted 28 May 2014 | Published 27 Jun 2014

Although diffractive optics have played a major role in nanoscale soft X-ray imaging, high-resolution and high-efciency diffractive optics have largely been unavailable for hard X-rays where many scientic, technological and biomedical applications exist. This is owing to the long-standing challenge of fabricating ultra-high aspect ratio high-resolution dense nano-structures. Here we report signicant progress in ultra-high aspect ratio nanofabrication of high-resolution, dense silicon nanostructures using vertical directionality controlled metal-assisted chemical etching. The resulting structures have very smooth sidewalls and can be used to pattern arbitrary features, not limited to linear or circular. We focus on the application of X-ray zone plate fabrication for high-efciency, high-resolution diffractive optics, and demonstrate the process with linear, circular, and spiral zone plates. X-ray measurements demonstrate high efciency in the critical outer layers. This method has broad applications including patterning for thermoelectric materials, battery anodes and sensors among others.

DOI: 10.1038/ncomms5243

Ultra-high aspect ratio high-resolution nanofabrication for hard X-ray diffractive optics

Chieh Chang1 & Anne Sakdinawat1

1 SLAC National Accelerator Laboratory, Stanford Synchrotron Radiation Lightsource, 2575 Sand Hill Road MS69, Menlo Park, California 94025, USA. Correspondence and requests for materials should be addressed to A.S. (email: mailto:[email protected]

Web End [email protected] ).

NATURE COMMUNICATIONS | 5:4243 | DOI: 10.1038/ncomms5243 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications 1

& 2014 Macmillan Publishers Limited. All rights reserved.

ARTICLE NATURE COMMUNICATIONS | DOI: 10.1038/ncomms5243

Diffractive optics have played a major role in nanoscale X-ray imaging1 and focusing in the soft X-ray region. X-ray microscopes capable of mapping material

properties, performing tomography and probing various types of samples from computer chips to biological cells in the tens of nanometres resolution have become a powerful scientic tool. However, in the hard X-ray region where penetration lengths are much greater and thicker samples can be studied, it is more difcult to control the wavefront of X-rays with both high-efciency and high-resolution owing to the difculty in fabricating ultra-high aspect ratio diffractive optics2. The ability to fabricate high-efciency hard X-ray diffractive optics using vertical directionality controlled metal-assisted chemical etching (V-MACE) (Fig. 1a) opens up new opportunities for high-resolution microscopy with compact X-ray sources and for more sophisticated wavefront manipulating capabilities for synchrotrons and X-ray-free electron lasers.

High-resolution, high-efciency X-ray diffractive optics, such as zone plates, are challenging to fabricate because of the need to make dense, very high aspect ratio, nanoscale structures to maintain both high spatial resolution and high diffraction efciency. The smallest features, located at the outermost zones of the zone plate, dene the numerical aperture of the lens at a given wavelength. The diffraction efciency is related to the zone thicknesses, wavelength, and material. Higher X-ray energies require thicker zones for efcient focusing and, therefore, require zone plates with ultra-high aspect ratio nanostructures. For extremely high aspect ratio and high resolutions typically o10 nm, volume effects35 occur, and to gain efciency zones must be tilted/tapered.

Current methods used to produce X-ray diffractive optics include top-down methods involving patterning of a thick resist mould6,7, pattern transfer into a substrate using deep reactive ion etching810, anisotropic Si wet etch11,12, multiple patterning techniques13, multilayer Laue lens, various multilayer-sliced zone plate techniques14, lithographic stacking15 and mechanical stacking16. Advantages and tradeoffs exist with each method. For example, traditional top-down diffractive optics fabrication methods commonly result in aspect ratios of 12:1 or less, but are relatively simple to produce. Mechanical stacking is currently the most used technique for producing high aspect ratio X-ray diffractive optics. Although possible, challenges exist for stacking more than two zone plates. Multilayer Laue lenses can achieve very high aspect ratio but are limited to linear structures and small effective areas. Focusing in two dimensions requires a pair of lenses and a reduction in efciency proportional to the number of lenses used. Multilayer-sliced zone plate techniques such as the method using atomic layer deposition and focused ion beam can produce very high aspect ratio structures with very small feature sizes but are limited to circular structures, small effective areas and errors in zone shapes. The benets of fabricating diffractive X-ray optics using the technique described here include the ability to fabricate large area structures, important for maintaining sufcient working distance, with arbitrary geometries and patterns, the ability to focus in two dimensions using a single diffractive optical element and the simplicity of a single-step lithographic process.

MACE using noble metals, rst reported by Li and Bohn17, is a simple and low-cost method used to fabricate Si nanowires, nanoporous silicon and nanopillars1821. Several reviews22,23 can

a

1

2

3

4

5

PMMA

PMMA

b

Si

Si

Si

Si

Si

Ti/Au PMMA

c

Ti/Au

Ti/Au

Figure 1 | Process ow and high aspect ratio zone plates. (a) Schematic of general process ow for metal-assisted chemical etching (MACE). (a1) Resist is spun on the wafer. (a2) Resist is exposed and developed. (a3) A thin layer of Ti and Au is electron-beam-evaporated onto the sample, and aliftoff is performed. (a4) The metal layer remains on the top of the wafer. The sample and etchant mixture consisting of HF, H2O2 and H2O are cooled. (a5)

A droplet of the etchant is placed onto the sample and etching takes place. The mask moves with the etching front, creating structured trenchesin the silicon. Vertical directionality controlled MACE causes the etching front to proceed vertically, and in this case is controlled by the pattern design in step 2, the thickness of the metal layers in step 3, and the temperature of the etching in step 5. (b) Scanning electron microscope (SEM) image of a zone plate pattern produced using vertical directionality controlled MACE. Scale bar, 5 mm. (c) Cross-sectional view of the zone plate produced using V-MACE.

The outermost zone widths of the zone plate are 100 nm. Scale bar, 2 mm.

2 NATURE COMMUNICATIONS | 5:4243 | DOI: 10.1038/ncomms5243 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications

& 2014 Macmillan Publishers Limited. All rights reserved.

NATURE COMMUNICATIONS | DOI: 10.1038/ncomms5243 ARTICLE

be found on the topic of MACE. In MACE, a noble metal layer, such as Au, is patterned onto the substrate. This serves as the etch mask. An etchant solution consisting of hydrogen peroxide (H2O2), hydrouoric acid (HF) and water (H2O) is placed onto the pattern and substrate, and Si is etched, creating trenches in the substrate. Movement of the metal catalyst during the etching process, such as sliding, rotation and folding24, has been shown to create interesting three-dimensional patterns. However, because of this movement, the aspect ratio achievable for vertical features in an isolated, arbitrary pattern has been limited.

In this paper, we describe vertical directionality controlled MACE (V-MACE), a method capable of fabricating vertical features in an arbitrary nanoscale pattern with over 100:1 aspect ratio, and use it to create ultra-high aspect ratio X-ray zone plates such as those illustrated in Fig. 1b. V-MACE involves the use of additional electron-hole-concentration balancing structures, metal anchors internal or external to a desired structure and appropriate etch chemistry. Advantages of this method include the ability to etch a dened pattern specic to the application of interest including complex, curved, linear or non-linear patterns. It is also a simple fabrication method requiring only a single lithography step combined with a wet etch. Large diameter optics combined with ultra-high aspect ratio features at high resolution can be achieved, and the structure fabricated using this method is easily compatible with common metallization techniques as well as mechanical stacking methods. As a demonstration of the utility of this fabrication technique, platinum atomic layer deposition of a Si zone plate mould is described, along with zone plate efciency measurements using 8.995 keV X-rays, which resulted in a 20.1% rst-order efciency with the highest resolution zones.

ResultsEffect of electron-hole concentration balancing structures. During MACE, electron holes are constantly generated and injected into silicon. They diffuse into the silicon isotropically and can be modelled as a two-dimensional constant-source diffusion process described by complementary error functions19. Therefore, as MACE progresses, the electron holes diffuse to the vicinity of

each AuSi interfaces, eventually, evolving to a prole distribution where the electron-hole concentration is highest at the centre of the Au metal lms, gradually decreasing towards the edge. This non-uniform electron hole distribution leads to differences in etch rates throughout a structure and is evidenced in the outward splaying effect observed in all our deep etch experiments, preventing the ability to create a vertical etch prole for isolated structures, as seen in Fig. 2a.

This splaying can be corrected using electron-hole concentration balancing structures to create a more uniform electron-hole distribution so as to induce a constant etch rate and thus achieve a vertical etch prole. Balancing structures are any additional structures located in regions where there is a large electron-hole concentration difference. For example, they can be used at the edges of isolated structures that provide additional electron-holes in the silicon during the MACE, and thus balanced concentration in the vicinity of areas where vertical etch directionality is desired. Balancing structures can take the form of a variety of geometries such as a plane catalyst stripe, perforated catalyst stripe, or any other means, not limited to the use of an additional metal catalyst, of creating a balanced electron-hole concentration at the edges, for example, using localized electric currents. In addition, the balancing structure can be induced in any direction relative to the isolated feature, to the side, above or below, such that the desired electron-hole concentration balance is obtained within the region of interest, and etch rates in this region become uniform.

As a demonstration of the effect of electron-hole concentration balancing structures, a high aspect ratio isolated linear grating has been fabricated, with and without the balancing structures, as seen in Fig. 2. The linear grating is 10 mm in width with a half period of 125 nm. Figure 2a shows a cross-section of the linear grating without the use of electron-hole concentration balancing structures. A splaying of the edges of features due to electron-hole concentration differences leads to non-vertical etching. Figure 2b shows a cross-section of the linear grating with the use of hole concentration balancing structures. The balancing structures in this case are solid stripes of Au catalyst 10 mm in width surrounding the edges of the linear grating. The catalyst dimensions and shape can be tailored to result in minimal

a

c

b

Figure 2 | Effect of electron-hole concentration balancing structures. (a) SEM image of an isolated array of 125 nm lines and spaces etched using MACE without vertical directionality control. Splaying results as a result of the imbalance in electron-hole concentration. Scale bar, 10 mm. (b) SEM image of an isolated array of 125 nm lines and spaces etched using MACE with vertical directionality control. Electron-hole balancing structures are shown to either side of the isolated line array. Lines are etched vertically. Scale bar, 10 mm. (c) SEM image of 100 nm 1:1 lines, 6.6 mm tall. Scale bar, 1 mm.

NATURE COMMUNICATIONS | 5:4243 | DOI: 10.1038/ncomms5243 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications 3

& 2014 Macmillan Publishers Limited. All rights reserved.

ARTICLE NATURE COMMUNICATIONS | DOI: 10.1038/ncomms5243

disturbance to the nal device, or to be used for further processing, for example, electroplating. It can be seen that the effects of the electron-hole concentration balancing structures result in vertical etch control of the linear grating.

Figure 2c demonstrates high aspect ratio fabrication of silicon gratings using this method. The grating in Fig. 2c has a half period of 100 nm and is 6.6 mm tall, resulting in an aspect ratio of 66:1.

High aspect ratio zone plates. We have fabricated ultra-high aspect ratio X-ray zone plates using this method. In order to obtain additional rigidity in the metal lm catalyst to prevent catalyst movements such as folding and sliding, thus minimizing distortion of the metal lms during the etching, we add metal anchors to the metal lm catalyst. The metal anchors in this case are external to the zones so that each of the zones becomes interconnected. This is illustrated in Fig. 3a. Variations in the anchoring pattern can result in different mechanical responses of the catalyst during etching. Some variations are shown in the SEM images of zone plate portions in Fig. 3b,c. In addition, to help mitigate the collapse of the zones during drying, we add buttressing structures that are discontinuities in the metal catalyst, such that the silicon zones can also be interconnected. This is useful for helping mechanically stabilize the silicon structure during the drying process and during further processing. It is also useful for the creation of a silicon free-standing zone plate or any other interconnected silicon structure.

Mechanical anchors can be external or internal to the feature. External anchors hold portions of the pattern together that, in this case, are the different zones. Internal anchors are created by holes in the catalyst that are smaller than the structure that needs to be patterned. They can be used both for stability in the metal catalyst lm and as a means for etching larger features, giving a physical pathway for etchants to diffuse. The remaining structures left by the internal anchors can be removed through various techniques including silicon oxidation and HF etching.

Figure 4a illustrates the fabrication of a very high aspect ratio zone plate in silicon with a diameter of 100 mm, outermost zone width of 100 nm and a duty cycle of 1:3. The duty cycle was designed such that atomic layer deposition can be performed later for zone doubling13, or so that the zone plate can be used for higher order diffraction25. The zone plate was mechanically cleaved to examine the cross-section. Figure 4b shows the sidewalls of this cross-section. The sidewalls after this etch are quite smooth and determined by the roughness in the metal catalyst. The thin vertical line, 30 nm in width, shown at the centre of the tilted zone segment is a silicon buttresses that connects the neighbouring zones. They can also be seen in Fig. 4a. The cross-section clearly demonstrates that high aspect ratio

features with a vertical prole has been achieved. Shown in Fig. 4c are lines that have 100 nm half period and are 14 mm tall.

However, porous silicon formation can be seen at the top of the structures along with some curvature. These can easily be removed with a silicon etch. The vertical portion of the features remains at over 12 mm tall, leading to an aspect ratio 4120:1. The inset in Fig. 4c shows a zoomed-in version of the lines, and control of the silicon lines, at 51 nm width.

High-resolution zone plates. Spiral zone plates that have previously been used to generate X-rays with orbital angular momentum26,27 were fabricated. A 2 2 array of spiral zone

plates, each with a square aperture, diameter of 60 mm, smallest outermost zone width of 60 nm, duty cycle of 1:3 and spiral charge of 20 were fabricated. In this case, the adjacent zone plates in the array served as the electron-hole balancing structures. Figure 5a shows a SEM image of the cross-section of this zone plate when mechanically cleaved. Uniformity in the etch depth across the range of feature sizes in the zone plate can be seen. Figure 5b shows zones close to the edge of the zone plate with 32 nm line width and 136 nm period, demonstrating a duty cycle of 1:3. The zones here are 2.5 mm tall creating aspect ratios of B40:1.

Platinum metallization and efciency testing of zone plates.

For use with hard X-rays, the silicon zone plate mould must be metallized, for example, through atomic layer deposition or electroplating. Electroplating provides high efciency throughout an entire zone plate area, whereas traditional atomic layer deposition provides the ability to create higher resolution zones with high efciency, but in a tradeoff of overall zone plate efciency. A combination of both methods, or variations of these methods, can be envisioned for achieving the benets of both techniques. In this experiment, Pt atomic layer deposition was performed, and efciency of the outermost zones was measured at 8.995 keV using the beamline 6.2 transmission X-ray microscope at the Stanford Synchrotron Radiation Light-source. A silicon zone plate mould was fabricated using V-MACE. A 5-nm layer of Al2O3 followed by a 45-nm layer of Pt were deposited as depicted in Fig. 6a. The nal platinum zone plate structure had a 50-nm outermost zone width, 200 mm diameter and 2.1 mm zone thickness. An SEM image of the resulting structure is shown in Fig. 6b. Local zone plate efciency measurements over a 30-mm diameter outermost zone region resulted in a 20.1% rst-order diffraction efciency. We note that this zone thickness will yield higher efciencies at energies 410 keV owing to more favourable phase-shifting properties of the Pt zones at higher energies.

a b c

Figure 3 | Metal interconnections and zone plate buttresses. (a) CAD image of metal interconnections and zone plate buttresses in a spiral zone plate data set. (b,c) Representative SEM images of metallized patterns produced by liftoff showing the metal interconnections as well as the gaps,which are the buttresses of the zone plate. Scale bars, 5 mm.

4 NATURE COMMUNICATIONS | 5:4243 | DOI: 10.1038/ncomms5243 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications

& 2014 Macmillan Publishers Limited. All rights reserved.

NATURE COMMUNICATIONS | DOI: 10.1038/ncomms5243 ARTICLE

a

c

b

Figure 4 | High aspect ratio zone plates. (a) SEM image of a deeply etched zone plate with a mechanically cleaved portion showing the cross-section. Scale bar, 10 mm. (b) Side prole of the lines in cross-section. The thin lines in the centre are the zone plate buttresses providing structural stability to the consecutive zones. Metal is seen at the bottom of the zones. Sidewalls are smooth. Scale bar, 500 nm. (c) Cross-sectional image of the zones demonstrating very deep, vertical etching. Scale bar, 2 mm. The inset shows that the line widths are 51 nm at an B1:3 line to space ratio. Scale bar in the inset, 1 mm.

DiscussionIn this paper, we have described how ultra-high aspect ratio etched silicon zone plate moulds were fabricating using V-MACE. Because a zone plate consists of a large range of feature sizes, larger in the centre and smaller in the outermost zones, etch rate variations as a function of zone width needs to be controlled for uniform, vertical etching. We minimize this by using low temperature and low H2O2 concentrations, along with appropriate dimensional variations in the pattern, such as catalyst interconnection density and Si zone buttress density. The low temperature and low H2O2 concentration causes the reduction reaction of H2O2 to become the rate-limiting step in MACE such that the etch rate variation, originally because of different etchant diffusion lengths of different feature sizes, is minimized.

This etching method is compatible with other catalyst patterning schemes. In this paper, a liftoff process was used to pattern the metal catalyst, but other methods can be used for patterning including, but not limited to, focused ion beam and reactive ion etching of the metal catalyst. It is important in all cases that the interface between the silicon and the metal catalyst be clean for directional control during the etching.

For the work described in this paper, Au catalysts were used. A thin Ti layer was also used, as an adhesion layer for the liftoff process, and later dissolved in the etchant solution. It is well known from the literature that other metal catalysts, such as Ag28 and Pt29, as well as other substrates such as GaAs30, can be etched

using this method. Therefore, this technique is not limited only to the specic catalyst material and substrate materials used here.

This simple fabrication method is suitable for creating optics optimized for the extreme ultraviolet (EUV) to the hard X-ray regime. For the hard X-ray regime, the zone plates can be combined with metallization techniques. Because the metal catalyst sinks to the bottom of the trench after etching, electroplating can be performed for metallization such that a gold zone plate can be made. In addition, atomic layer deposition for coating a variety of different types of materials, optimized for particular wavelengths, can also be performed. For example, Au zone plates with 6 mm thickness could produce up to 35% rst-order diffraction efciency at 25 keV photon energy. Au zone plates with 10 mm thickness could produce close to 40% rst-order diffraction efciency at 50 keV 31, the maximum efciency for a binary phase zone plate. In addition, combining two zone plates with different patterns such that a blazed zone plate prole15 is created through mechanical stacking could further increase the efciency.

For EUV and soft X-rays, etching does not necessarily have to be very deep. As it is currently possible to create nanowires o10 nm wide using conventional MACE, we believe it should be possible to etch similar dimensions for X-ray optics applications through application of V-MACE. In addition, it is also possible to directly use the silicon lens and forgo the metallization or material deposition process for softer X-ray energies. For

NATURE COMMUNICATIONS | 5:4243 | DOI: 10.1038/ncomms5243 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications 5

& 2014 Macmillan Publishers Limited. All rights reserved.

ARTICLE NATURE COMMUNICATIONS | DOI: 10.1038/ncomms5243

a

Pt

Si

Al2O3

a

b

b c

Figure 5 | High-resolution zone plates. (a) SEM image of a cleaved spiral zone plate from a 2 2 array of zone plates. The cross-sectional view

shows uniformity in etching depth over a range of feature sizes in the zone plate. Scale bar, 5 mm. (b) Cross-sectional views of some of the small zones in this zone plate. Line widths are B32 nm and 2.5 mm tall, and the period is 136 nm. Scale bar, 500 nm. (c) A top-down view of the etched zone plate of a charge 20 spiral zone plate. Scale bar, 5 mm.

Figure 6 | Pt metallization for X-ray zone plates. (a) Schematic of Pt atomic layer deposition of Si zone plate structure. The starting Si zone plate mould is shown in red. A 5-nm layer of Al2O3 is deposited followed bya 45-nm layer of Pt. The coating is conformal over the entire Si zone plate mould. (b) Cross-sectional SEM image of a focused ion beam sectioned zone plate. The image is taken at a tilt angle of 52 degrees. Scale bar, 1 mm.

example, with 50 eV radiation, a silicon zone plate with 280 nm thickness could produce a theoretical rst-order efciency of B27%. For 700900 eV wavelength, in the soft X-ray region, a silicon zone plate of 1 mm thickness could produce a theoretical rst-order efciency of B2629%. In each of these cases there will be some area loss, resulting in slight lowering of the theoretical efciency owing to the Si buttress and catalyst anchor density, but overall efciencies will remain high compared with what is currently available. Volume effects, for example, in the case of vertical outermost zone widths approaching 10 nm and zone thicknesses approaching 1 mm, will cause a reduction in diffraction efciency unless the zones are tilted or appropriately shaped. In addition, as in the case of hard X-rays, these zone plates can be combined with existing concepts such as stacking to produce shaped, blazed zones, thicker or interleaved structures for increased efciency. For applications requiring free-standing zone plates, especially important at the low EUV energies, this fabrication process can be performed on commercially available single crystalline Si membranes.

In conclusion, we have demonstrated a simple process to fabricate ultra-high aspect ratio, dense features in a complex, non-repetitive nanostructure using vertical directionality controlled MACE, with optimizations of metal catalyst mechanical anchors, hole concentration balancing structures, low temperature etching and low H2O2 concentration for the case of X-ray zone plate optics fabrication. This leads to the capability to create high-efciency zone plate optics and more general X-ray diffractive optical structures such as coded apertures and

collimators for hard X-rays, far beyond what is currently available. The versatility of this ultra-high aspect ratio etching process for nanostructures can also lead to its utilization for a broad array of applications, including sensors and energy-related nanostructured materials, among others.

Methods

Lithographic process for linear gratings. A 60-nm-thick layer of 950 K Polymethyl methacrylate (PMMA) is spin coated onto a P-type, Boron-doped /100S CZ Prime silicon wafer with 1020 O cm resistivity (SiliconQuest). The resist layer is then baked at 170 C for 30 min and patterned with a 100-keV JEOL 6300 electron beam lithography system. The patterned resist was then developed in 1:3 MIBK (methyl isobutyl ketone): IPA (isopropyl alcohol) at 4 C for 30 s. An oxygen descum etch was performed to remove any residual PMMA. The metal catalyst layer that consists of 2 nm Ti and 15 nm Au is then electron beam evaporated onto the pattern. Liftoff was performed in acetone. The patterned piece and etching solution comprised of 5.3 M HF, 0.25 M H2O2 and 50 M H2O are cooled to 10 C, and a droplet of etchant is placed on top of the pattern. Etching was performed at 10 C for 40 min and then quenched with a H2O rinse. The pattern was dried using nitrogen.

Lithographic process for high aspect ratio zone plates. A 300-nm-thick layer of ZEP520A is spin coated on a P-type, /100S FZ Prime silicon wafer with

6 NATURE COMMUNICATIONS | 5:4243 | DOI: 10.1038/ncomms5243 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications

& 2014 Macmillan Publishers Limited. All rights reserved.

NATURE COMMUNICATIONS | DOI: 10.1038/ncomms5243 ARTICLE

410,000 O cm resistivity (SiliconQuest). The resist was patterned with a 100-keV JEOL 6300 electron beam lithography system. The patterned resist was then developed in xylenes at 20 C for 40 s. An oxygen descum etch was performed to remove any residual ZEP520A. The metal catalyst layer, 2 nm Ti and 75 nm Au, was then electron beam evaporated onto the pattern. Liftoff was performed in Remover PG (MicroChem) at 70 C. The patterned piece and etching solution comprised of 5.3 M HF, 0.25 M H2O2 and 50 M H2O were cooled to 6 C using a cold plate, and a droplet of etchant was placed on top of the pattern. Etching was performed at 6 C for 90 min and then quenched with a H2O rinse. H2O was replaced with isopropyl alcohol, and the sample was dried using a critical point dryer (Tousimis).

Lithographic process for high-resolution zone plates. A 60-nm-thick layer of 950 K PMMA is spin coated onto a P-type, Boron-doped /100S CZ Prime silicon wafer with 1020 O cm resistivity (SiliconQuest). The resist layer is then baked at 170 C for 30 min and patterned with a 100-keV JEOL 6300 electron beam lithography system. The patterned resist was then developed in 1:3 MIBK:IPA at 4 C for 30 s. An oxygen descum etch was performed to remove any residual PMMA. The metal catalyst layer that consists of 2 nm Ti and 15 nm Au is then electron beam evaporated onto the pattern. Liftoff was performed in acetone. The patterned piece and etching solution comprised of 5.3 M HF, 0.25 M H2O2 and 50 M H2O are cooled to 10 C, and a droplet of etchant is placed on top of the pattern. Etching was performed at 10 C for 30 min and then quenched with a H2O rinse. The pattern was dried using nitrogen.

Pt metallization and zone plate efciency measurement. A Si zone plate mould was fabricated using V-MACE. A 5-nm layer of Al2O3 followed by a 45-nm Pt layer was deposited onto the zone plate mould, resulting in a zone plate with 50 nm outermost zone width, 200 mm diameter and 2.1 mm zone thickness. The zone plate was then placed in the transmission X-ray microscope at beamline 6.2 at the Stanford Synchrotron Radiation Lightsource for zone plate efciency measurements. The energy used for the measurement was 8.995 keV. A 30-mm pinhole diameter was placed behind a portion of the capillary condenser optic of the microscope to restrict the illumination area of the zone plate. In order to obtain the reference intensity, the zone plate was moved out of the way, whereas the radiation still passed through the pinhole and substrate. The intensity of the spot at the CCD was integrated. To obtain the diffracted efciencies, the zone plate was then placed behind the same illumination area, and the diffracted spots were observed at the CCD. The total radiation of the rst-order diffracted spot was integrated, and the rst-order diffraction efciency was calculated by taking the ratio of the radiation in the rst-order diffraction spot with the radiation in the reference spot.

References

1. Sakdinawat, A. & Attwood, D. Nanoscale X-ray Imaging. Nat. Photon. 4, 840848 (2010).

2. Wu, S.-R., Hwu, Y. & Margaritondo, G. Hard-X-ray zone plates: recent progress. Materials 5, 17521773 (2012).

3. Maser, J. & Schmahl, G. Coupled wave description of the diffraction by zone plates with high aspect ratios. Opt. Commun. 89, 355362 (1992).

4. Rehbein, S. & Schneider, G. Volume zone plate development at BESSY. IPAP Conference Series 7, 103106 (2005).

5. Stephan Rehbein, S. H., Guttmann, P., Werner, S. & Schneider, G. High-resolution soft X-ray Microscopy with zone plates in high orders of diffraction. Phys. Rev. Lett. 103, 110801 (2009).

6. Vila-Comamala, J. et al. Dense high aspect ratio hydrogen silsesquioxane nanostructures by 100 keV electron beam lithography. Nanotechnology 21, 285305 (2010).

7. Gorelick, S., Guzenko, V. A., Vila-Comamala, J. & David, C. Direct e-beam writing of dense and high aspect ratio nanostructures in thick layers of PMMA for electroplating. Nanotechnology 21, 295303 (2010).

8. Marty, F. et al. Advanced etchign of silicon based on deep reactive ion etching for silicon high aspect ratio microstructures and three-dimensional micro- and nanostructures. Microelectron. J. 36, 673677 (2005).

9. Wu, B., Kumar, A. & Sharma, P. High aspect ratio silicon etch: a review. J. Appl. Phys. 108 (2010).

10. Uhlen, F. et al. New diamond nanofabrication process for hard x-ray zone plates. J. Vac. Sci. Technol. B 29, 06FG03 (2011).

11. Kendall, D. L. Vertical etching of silicon at very high aspect ratios. Annu. Rev. Mater. Sci. 9, 373403 (1979).

12. Heilmann, R. K., Bruccoleri, A. R., Mukherjee, P. & Schattenburg, M. L. Progress in the development of critical-angle transmission gratings. Proc. SPIE 8443, 84430W8443184438WW (2012).

13. Vila-Comamala, J. et al. Ultra-high resolution zone-doubled diffractive X-ray optics for the multi-keV regime. Opt. Express 19, 175184 (2011).

14. Mayer, M. et al. Efcient focusing of 8 keV X-rays with multilayer Fresnel zone plates fabricated by atomic layer deposition and focused ion beam milling.J. Synchrotron Radiat. 20, 433440 (2013).15. DiFabrizio, E. et al. High-efciency multilevel zone plates for keV X-rays. Nature 401, 895898 (1999).

16. Fang, Y. et al. Nanofabrication of high aspect ratio 24 nm x-ray zone plates for x-ray imaging applications. J. Vac. Sci. Technol. B 25, 20042007 (2007).17. Li, X. & Bohn, P. W. Metal-assisted chemical etching in HF/H2O2 produces porous silicon. Appl. Phys. Lett. 77, 2572 (2000).

18. Chern, W. et al. Nonlithographic patterning and metal-assisted chemical etching for manufacturing of tunable light-emitting silicon nanowire arrays. Nano Lett. 10, 15821588 (2010).

19. Lianto, P., Yu, S., Wu, J., Thompson, C. V. & Choi, W. K. Vertical etching with isolated catalysts in metal-assisted chemical etching of silicon. Nanoscale 4, 75327539 (2012).

20. Rykaczewski, K., Hildreth, O. J., Wong, C. P., Fedorov, A. G. & Scott, J. H. J. Guided three-dimensional catalyst folding during metal-assisted chemical etching of silicon. Nano Lett. 11, 23692374 (2011).

21. Wang, D., Ji, R., Du, S., Albrecht, A. & Schaaf, P. Ordered arrays of nanoporous silicon nanopillars and silicon nanopillars with nanoporous shells. Nanoscale Res. Lett. 8, 19 (2013).

22. Huang, Z., Geyer, N., Werner, P., Boor, J. d. & Gosele, U. Metal-assisted chemical etching of silicon: a review. Adv. Mater. 23, 285308 (2011).

23. Li, X. Metal assisted chemical etching for high aspect ratio nanostructures: A review of characteristics and applications in photovoltaics. Curr. Opin. Solid State Mater. Sci. 16, 7181 (2012).

24. Hildreth, O. J., Lin, W. & Wong, C. P. Effect of catalyst shape and etchant composition on etching direction in metal-assisted chemical etching of silicon to fabricate 3D nanostructures. ACS Nano 3, 40334042 (2009).

25. Schneider, G. Zone plates with high efciency in high orders of diffraction described by dynamical theory. Appl. Phys. Lett. 71, 22422242 (1997).

26. Sakdinawat, A. & Liu, Y. Soft X-ray microscopy using spiral zone plates. Opt. Lett. 32, 26352637 (2007).

27. Yao, A. M. & Padgett, M. J. Orbital angular momentum: origins, behavior and applications. Adv. Optics Photon. 3, 161204 (2011).

28. Zhipeng Huang, H. F. & Zhu, J. Fabrication of silicon nanowire arrays with controlled diameter, length, and density. Adv. Mater. 19, 744748 (2007).29. Chia-Lung Lee, K. T., Kanda, Y., Ikeda, S. & Matsumura, M. Pore formation in silicon by wet etching using micrometre-sized metal particles as catalysts.J. Mater. Chem. 18, 10151020 (2008).30. Matt DeJarld, J. C. S. et al. Formation of high aspect ratio GaAs nanostructues with metal assisted chemical etching. Nano Lett. 11, 52595263 (2011).

31. Shastri, S. D., Maser, J. M., Lai, B. & Tys, J. Microfocusing of 50 keV undulator radiation with two stacked zone plates. Opt. Commun. 197, 914 (2001).

Acknowledgements

We thank Ludwig Galambos, Remus Albu, Richard Tiberio, Tom Carver, Clifford Knollenberg, Roger Chen, Raymond Leung, Michael Feser, Johanna Weker and Linda Geniesse. This research was funded by the DARPA Quantum Orbital Resonance Spectroscopy Program (QORS). Part of this work was performed at the Stanford Nano Shared Facilities and at the Stanford Nanofabrication Facility.

Author contributions

C.C. performed the nanofabrication experiments; A.S. conceived the experiment and performed the X-ray experiments; C.C. and A.S. analysed the data, discussed the results and implications at all stages, and wrote the paper.

Additional information

Competing nancial interests: The authors declare no competing nancial interests.

Reprints and permission information is available online at http://npg.nature.com/reprintsandpermissions/

Web End =http://npg.nature.com/ http://npg.nature.com/reprintsandpermissions/

Web End =reprintsandpermissions/

How to cite this article: Chang, C. and Sakdinawat, A. Ultra-high aspect ratio high-resolution nanofabrication for hard X-ray diffractive optics. Nat. Commun. 5:4243 doi: 10.1038/ncomms5243 (2014).

NATURE COMMUNICATIONS | 5:4243 | DOI: 10.1038/ncomms5243 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications 7

& 2014 Macmillan Publishers Limited. All rights reserved.