Vacuum Ultraviolet Field Emission Lamp Consisting of Neodymium Ion Doped Lutetium Fluoride Thin Film as Phosphor

Abstract

A vacuum ultraviolet (VUV) field emission lamp was developed by using a neodymium ion doped lutetium fluoride (Nd3+ : LuF3) thin film as solid-state phosphor and carbon nanofiber field electron emitters. The thin film was synthesized by pulsed laser deposition and incorporated into the lamp. The cathodoluminescence spectra of the lamp showed multiple emission peaks at 180, 225, and 255 nm. These emission spectra were in good agreement with the spectra reported for the Nd3+ : LuF3 crystal. Moreover, application of an acceleration voltage effectively increased the emission intensity. These results contribute to the performance enhancement of the lamp operating in the VUV region.

Masahiro Yanagihara 1 and Takayuki Tsuji 1 and Mohd Zamri Yusop 1, 2 and Masaki Tanemura 1 and Shingo Ono 1 and Tomohito Nagami 3 and Kentaro Fukuda 3 and Toshihisa Suyama 3 and Yuui Yokota 4 and Takayuki Yanagida 5 and Akira Yoshikawa 4

Academic Editor:Xiao-Feng Zhao

1, Nagoya Institute of Technology, Gokiso-cho, Showa-ku, Nagoya, Aichi 466-8555, Japan
2, Department of Materials, Manufacturing & Industrial , Faculty of Mechanical Engineering, Universiti Teknologi Malaysia (UTM), 81310 Skudai, Johor, Malaysia
3, Tokuyama Corporation, Kasumigaseki Common Gate West Tower 2-1, Kasumigaseki 3-chome, Chiyoda-ku, Tokyo 100-8983, Japan
4, Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577, Japan
5, Kyushu Institute of Technology, 2-4 Hibikino, Wakamatsu-ku, Kitakyushu 808-0196, Japan

Received 16 July 2014; Accepted 24 August 2014; 11 September 2014

This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

1. Introduction

Vacuum ultraviolet (VUV) light has been used in numerous fields, such as cleaning, surface modification, and sterilization, because short wavelength light with high photon energy is capable of breaking strong chemical bonds [1-3]. Therefore, performance improvements of VUV lamps contribute to the progress of these applications. The VUV gas lamp has widely been used [4-6] but presents limited stability, lifetime, and size. VUV lamps using a solid-state phosphor have attracted considerable attention as alternate light sources because they exhibit less deterioration, less fluctuation, and higher density than gas lamps [7, 8]. These lamps require wide band gap materials but few solid-state phosphors have substantial band gaps. Group III nitrides are suitable because they present a direct transition type band structure with a wide band gap [9, 10]. However, even when using AlN, which emits light at a relatively short wavelength, the operating wavelength was limited to deep UV region [9, 11-13]. The wide band gap of diamond can be applied to UV but not to VUV lamps [14]. On the other hand, some fluorides have band gaps that are sufficiently wide to enable light emission in the VUV region [15, 16]. Fluoride composite materials have been widely studied as laser materials, scintillation materials, and optical materials because of their extremely wide band gap [17-24]. Specifically, a KMgF₃ thin film acting as a solid-state phosphor and carbon nanofiber (CNF) field electron emitter has previously been incorporated into a VUV lamp [25]. The emission spectra from the lamp showed two emission peaks at 155 and 180 nm in the 140-200 nm wavelength range, showing that solid-state phosphors can be exploited in VUV lamps.

Neodymium ion doped lutetium fluoride (Nd³⁺ : LuF₃ ), whose cathodoluminescence (CL) efficiency is almost equivalent to KMgF₃ , was selected as a phosphor to develop a new VUV lamp. This lamp also consisted of CNFs field electron emitters. Among Nd³⁺ ion doped fluoride materials that emit VUV light, such as Nd³⁺ : LuF₃ , Nd³⁺ : LaF₃ , and Nd³⁺ : LuLiF₄ [26-28], Nd³⁺ : LuF₃ single crystals have reported the highest X-ray excited luminescence conversion efficiency [26]. However, large Nd³⁺ : LuF₃ single crystals have proven difficult to grow because of the occurrence of a hexagonal to orthorhombic phase transition (ca. 950°C) during the crystal growth process [26]. The stress caused by this structural reconfiguration results in crack formation in Nd³⁺ : LuF₃ single crystals. In contrast, growth of thin film suppresses these cracks owing to reducing stress by depositing small particles. For this reason, we fabricated Nd³⁺ : LuF₃ thin film by pulsed laser deposition (PLD) to deposit small particles. In addition, PLD has produced fewer chemical composition discrepancies between source targets and deposited thin films. Consequently, the fabrication of fluoride thin films by PLD does not require the utilization of the toxic fluorine gas [29].

2. Experimental Methods

2.1. Thin Film Fabrication

The target was prepared by pressing a 1 : 9 NdF₃ -LuF₃ powder mixture. A (001)-oriented MgF₂ crystal (20 mm × 20 mm × 0.5 mm) mounted on a rotating holder was used as a substrate and was maintained at 400°C during PLD. This substrate temperature was chosen because previous experiments on the growth of Nd³⁺ : LaF₃ thin films showed that substrate heating improved crystalline quality and VUV luminescence quantum efficiency and resulted in optimal performance at 400°C [27]. The thin film was deposited by irradiating the Nd³⁺ : LuF₃ target with the third harmonics of a Nd : YAG laser (355 nm in wavelength). The 2 mm diameter laser spot was focused on the target at a fluence of 2.5 J/cm² and a repetition rate of 10 Hz. The deposition was carried out for 8 h at an average pressure of 3 × 10^-4 Pa without atmosphere control.

2.2. Field Emission Lamp Construction

CNFs were grown by bombarding a grassy carbon substrate with Ar⁺ at room temperature [30-32]. The ion beam, which had a diameter of 6 cm, was set at an incident angle of 45° and energy of 1 keV, respectively. The length and diameter of CNFs were 0.3-2 and 20 mm, respectively, with an approximate density of 5 × 10⁸ cm^-2 . Figure 1 shows the schematic of the lamp. In addition to the CNFs and the thin film, the lamp contained two copper mesh electrodes with a mesh width of 0.1 mm. Two teflon spacer plates were used to prevent short circuits and provide space for electron acceleration. A 200 µ m thick spacer was placed between CNFs and a copper electrode and a 5 mm thick spacer was placed between the two copper electrodes. In this lamp, electrons were emitted from CNFs using the extraction voltage and accelerated toward the thin film using the acceleration voltage. VUV CL from the Nd³⁺ : LuF₃ thin film was emitted through the substrate. A substrate with high transmittance in the VUV region was needed to output light efficiently and MgF₂ , which exhibited 94% transmittance at 180 nm, satisfied this condition. The lamp benefited from a low power consumption and reduced thermal effects when the field electron emitters were used as cold cathodes [33, 34]. The lamp was operated in the vacuum chamber at an average pressure of 8 × 10^-5 Pa.

Figure 1: Schematic diagram of VUV field emission lamp. SEM image of CNFs is shown in the insert.

[figure omitted; refer to PDF]

3. Results and Discussion

The thickness and surface morphology of the Nd³⁺ : LuF₃ thin film was investigated by using scanning electron microscopy (SEM). The thin film contained some droplets with cracks that originate from structural phase transitions. In contrast, the uniform layer was about 15 nm thick without any cracks. The crystallographic properties were also evaluated by using X-ray diffraction. The high and sharp diffraction patterns indicated the well crystallization of the thin film. The detailed data of these evaluations are described in [29].

Figure 2 shows the CL spectra of the Nd³⁺ : LuF₃ thin film at different acceleration voltages ranging from 1 to 20 kV. The electron beam current was kept at 600 pA during the CL measurements. The spectra showed a dominant peak in the VUV region at 179 nm and two additional emission peaks at 223 and 255 nm, which are consistent with the emission peaks observed for Nd³⁺ : LuF₃ single crystals [17]. These results show that although the PLD target was obtained by pressing NdF₃ and LuF₃ powders together (undoped material), Nd³⁺ acted as a dopant for LuF₃ and a luminescent center in the thin film.

Figure 2: CL spectra of the Nd³⁺ : LuF₃ thin film at acceleration voltages ranging from 1 to 20 kV.

[figure omitted; refer to PDF]

The influence of the acceleration voltage on the CL intensity of the Nd³⁺ : LuF₃ thin film at 180 nm was also investigated as shown in Figure 3. The CL intensity increased with increasing acceleration voltage before saturation at 25 kV. This result suggests that incident electrons passed through the thin film before giving all their energy to the thin film at 25 kV.

Figure 3: Output CL intensity of the Nd³⁺ : LuF₃ thin film at 179 nm for acceleration voltages ranging from 1 to 25 kV.

[figure omitted; refer to PDF]

The emission spectra of the lamp were measured at different acceleration voltages ranging from 1 to 2.5 kV. The extraction voltage was kept at 600 V during the measurements. The emission spectra (Figure 4) presented a dominant peak in the VUV region at 180 nm and two additional peaks at 225 and 255 nm. These spectra closely matched the emission spectra obtained for the Nd³⁺ : LuF₃ thin film.

Figure 4: Emission spectra of the lamp at acceleration voltages ranging from 1 to 2.5 kV.

[figure omitted; refer to PDF]

The influence of the acceleration voltage on the CL intensity of the lamp at 180 nm was evaluated. The CL intensity (Figure 5) showed a nonlinear dependence on the acceleration voltage, which was attributed to an increase of the electron diffusion region in the thin film. The output power of this lamp may amount to several microwatts because Nd³⁺ : LuF₃ and KMgF₃ show quasiequivalent conversion efficiencies [16]. An increase in acceleration voltage may therefore efficiently enhance the output power of this lamp.

Figure 5: Output CL intensity of the lamp at 180 nm for acceleration voltages ranging from 1 to 2.5 kV.

[figure omitted; refer to PDF]

The luminescence area of this VUV lamp can easily generate a large area with little thermal effect and low power consumption by employing a CNF field electron emitter. In addition a solid-state phosphor brings many benefits in the VUV lamp such as safety, longevity, stability, and downsizing.

4. Conclusions

In summary, a VUV field emission lamp consisting of a Nd³⁺ : LuF₃ thin film as a solid-state phosphor and CNF field electron emitter was fabricated. The CL spectra of the lamp showed multiple emission peaks at 180, 225, and 255 nm, which were in good agreement with emission spectra previously reported for the Nd³⁺ : LuF₃ crystal. This result suggested that Nd³⁺ ion acted as a luminescent center and doped LuF₃ in the synthesized thin film although the target used during PLD was obtained by pressing NdF₃ and LuF₃ powders into a pellet. Furthermore, the output emission intensity showed a nonlinear response to the acceleration voltage, indicating that an increase in acceleration voltage may significantly enhance this output emission intensity. Although recent gas lamps are improving their performances, this lamp may soon become one of the candidates of VUV light sources. These techniques are essential to numerous applications, such as sterilization, surface cleaning, and synthesis and degradation of chemical material.

Acknowledgments

This research was partially supported by a Grant-in-Aid for Scientific Research C (40370126), from the Japan Society for the Promotion of Science (JSPS), Nippon Sheet Glass Foundation, and Nanotechnology Platform Program (Molecule and Material Synthesis) of the Ministry of Education, Culture, Sports, Science and Technology (MEXT), Japan. The authors would like to thank Professor Y. Ichikawa of the Nagoya Institute of Technology (NIT) for invaluable discussions. The authors are grateful to Dr. S. Nakao of the Institute for Molecular Science (IMS) for important technical support in this research. The authors would like to thank Enago (http://www.enago.jp/) for the English Language review.

Conflict of Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

References

[1] J. R. Vig, "UV/ozone cleaning of surfaces," Journal of Vacuum Science & Technology A , vol. 3, pp. 1027, 1985.

[2] L. J. Matienzo, J. A. Zimmerman, F. D. Egitto, "Surface modification of fluoropolymers with vacuum ultraviolet irradiation," Journal of Vacuum Science & Technology A , vol. 12, pp. 2662, 1994.

[3] S. Lerouge, A. C. Fozza, M. R. Wertheimer, R. Marchand, L. Yahia, "Sterilization by low-pressure plasma: the role of vacuum-ultraviolet radiation," Plasmas and Polymers , vol. 5, no. 1, pp. 31-46, 2000.

[4] J. Wieser, D. E. Murnick, A. Ulrich, H. A. Huggins, A. Liddle, W. L. Brown, "Vacuum ultraviolet rare gas excimer light source," Review of Scientific Instruments , vol. 68, no. 3, pp. 1360-1364, 1997.

[5] J. Y. Zhang, I. W. Boyd, "Efficient excimer ultraviolet sources from a dielectric barrier discharge in rare-gas/halogen mixtures," Journal of Applied Physics , vol. 80, pp. 633, 1996.

[6] A. C. Fozza, A. Kruse, A. Holländer, A. Ricard, M. R. Wertheimer, "Vacuum ultraviolet to visible emission of some pure gases and their mixtures used for plasma processing," Journal of Vacuum Science and Technology A: Vacuum, Surfaces and Films , vol. 16, no. 1, pp. 72-77, 1998.

[7] K. Watanabe, T. Taniguchi, T. Niiyama, K. Miya, M. Taniguchi, "Far-ultraviolet plane-emission handheld device based on hexagonal boron nitride," Nature Photonics , vol. 3, no. 10, pp. 591-594, 2009.

[8] A. Bergh, G. Craford, A. Duggal, R. Haitz, "The promise and challenge of solid-state lighting," Physics Today , vol. 54, no. 12, pp. 42-47, 2001.

[9] I. Akasaki, H. Amano, H. Murakami, M. Sassa, H. Kato, K. Manabe, "Growth of GaN and AlGaN for UV/blue p-n junction diodes," Journal of Crystal Growth , vol. 128, no. 1-4, pp. 379-383, 1993.

[10] I. Akasaki, H. Amano, "Crystal growth and conductivity control of group III nitride semiconductors and their application to short wavelength light emitters," Japanese Journal of Applied Physics , vol. 36, no. 9A, pp. 5393, 1997.

[11] W. M. Yim, E. J. Stofko, P. J. Zanzucchi, J. I. Pankove, M. Ettenberg, S. L. Gilbert, "Epitaxially grown AlN and its optical band gap," Journal of Applied Physics , vol. 44, no. 1, pp. 292-296, 1973.

[12] E. Silveira, J. A. Freitas, S. B. Schujman, L. J. Schowalter, "AlN bandgap temperature dependence from its optical properties," Journal of Crystal Growth , vol. 310, no. 17, pp. 4007-4010, 2008.

[13] T. Oto, R. G. Banal, K. Kataoka, M. Funato, Y. Kawakami, "100 mW deep-ultraviolet emission from aluminium-nitride-based quantum wells pumped by an electron beam," Nature Photonics , vol. 4, no. 11, pp. 767-771, 2010.

[14] S. Koizumi, K. Watanabe, M. Hasegawa, H. Kanda, "Ultraviolet emission from a diamond pn junction," Science , vol. 292, no. 5523, pp. 1899-1901, 2001.

[15] T. Nishimatsu, N. Terakubo, H. Mizuseki, Y. Kawazoe, D. A. Pawlak, K. Shimamura, T. Fukuda, "Band structures of perovskite-like fluorides for vacuum-ultraviolet-transparent lens materials," Japanese Journal of Applied Physics 2: Letters , vol. 41, no. 4, pp. L365-L367, 2002.

[16] S. Ono, R. El Ouenzerfi, A. Quema, H. Murakami, N. Sarukura, T. Nishimatsu, N. Terakubo, H. Mizuseki, Y. Kawazoe, A. Yoshikawa, T. Fukuda, "Band-structure design of fluoride complex materials for deep-ultraviolet light-emitting diodes," Japanese Journal of Applied Physics , vol. 44, no. 10, pp. 7285-7290, 2005.

[17] P. J. Key, R. C. Preston, "Magnesium fluoride windowed deuterium lamps as radiance transfer standards between 115 and 370 nm," Journal of Physics E: Scientific Instruments , vol. 13, no. 8, pp. 866, 1980.

[18] Y. Hatanaka, H. Yanagi, T. Nawata, Y. Inui, T. Mabuchi, K. Yasumura, E. Nishijima, T. Fukuda, "Properties of ultra-large CaF₂ crystals for the high NA optics," in Optical Microlithography XVIII, vol. 5754, of Proceedings of SPIE, 2005.

[19] T. Kozeki, Y. Suzuki, M. Sakai, H. Ohtake, N. Sarukura, Z. Liu, K. Shimamura, K. Nakano, T. Fukuda, "Observation of new excitation channel of cerium ion through highly vacuum ultraviolet transparent LiCAF host crystal," Journal of Crystal Growth , vol. 229, no. 1, pp. 501-504, 2001.

[20] A. Yoshikawa, T. Yanagida, Y. Yokota, N. Kawaguchi, S. Ishizu, K. Fukuda, T. Suyama, K. J. Kim, J. Pejchal, M. Nikl, K. Watanabe, M. Miyake, M. Baba, K. Kamada, "Single crystal growth, optical properties and neutron response of Ce³⁺ doped LiCaAlFg," IEEE Transactions on Nuclear Science , vol. 56, no. 6, pp. 3796-3799, 2009.

[21] N. Kawaguchi, T. Yanagida, A. Novoselov, K. J. Kim, K. Fukuda, A. Yoshikawa, M. Miyake, M. Baba, "Neutron responses of Eu²⁺ activated LiCaAIF6 scintillator," in Proceedings of the IEEE Nuclear Science Symposium Conference Record (NSS/MIC '08), pp. 1174-1176, Dresden, Germany, October 2008.

[22] R. Visser, P. Dorenbos, C. W. E. van Eijk, A. Meijerink, H. W. den Hartog, "The scintillation intensity and decay from Nd³⁺ 4f² 5d and 4f³ excited states in several fluoride crystals," Journal of Physics: Condensed Matter , vol. 5, article 8437, 1993.

[23] S. Ono, Y. Suzuki, T. Kozeki, H. Murakami, H. Ohtake, N. Sarukura, H. Sato, S. Machida, K. Shimamura, T. Fukuda, "High-energy, all-solid-state, ultraviolet laser power-amplifier module design and its output-energy scaling principle," Applied Optics , vol. 41, no. 36, pp. 7556-7560, 2002.

[24] R. W. Waynant, P. H. Klein, "Vacuum ultraviolet laser emission from Nd⁺³ :LaF₃ ," Applied Physics Letters , vol. 46, pp. 14, 1985.

[25] M. Yanagihara, M. Z. Yusop, M. Tanemura, S. Ono, T. Nagami, K. Fukuda, T. Suyama, Y. Yokota, T. Yanagida, A. Yoshikawa, "Vacuum ultraviolet field emission lamp utilizing KMgF3 thin film phosphor," APL Materials , vol. 2, no. 4, 2014.

[26] K. Fukuda, S. Ishizu, N. Kawaguchi, T. Suyama, T. Yanagida, Y. Yokota, M. Nikl, A. Yoshikawa, "Crystal growth and optical properties of the Nd3+ doped LuF 3 single crystals," Optical Materials , vol. 33, no. 8, pp. 1143-1146, 2011.

[27] M. Ieda, T. Ishimaru, S. Ono, K. Yamanoi, M. Cadatal-Raduban, T. Shimizu, N. Sarukura, K. Fukuda, T. Suyama, Y. Yokota, T. Yanagida, A. Yoshikawa, "Optical characteristic improvement of neodymium-doped lanthanum fluoride thin films grown by pulsed laser deposition for vacuum ultraviolet application," Japanese Journal of Applied Physics , vol. 51, no. 2, 2012.

[28] A. F. H. Librantz, L. Gomes, S. L. Baldochi, I. M. Ranieri, G. E. Brito, "Luminescence study of the 4f25d configuration of Nd3+ in LiYF4, LiLuF4 and BaY2F8 crystals," Journal of Luminescence , vol. 121, no. 1, pp. 137-148, 2006.

[29] M. Ieda, T. Ishimaru, S. Ono, K. Yamanoi, M. Cadatal-Raduban, T. Shimizu, N. Sarukura, Y. Yokota, T. Yanagida, A. Yoshikawa, "Structural and optical properties of neodymium-doped lutetium fluoride thin films grown by pulsed laser deposition," Optical Materials , vol. 35, no. 12, pp. 2329-2331, 2013.

[30] M. Tanemura, T. Okita, H. Yamauchi, S. Tanemura, R. Morishima, "Room-temperature growth of a carbon nanofiber on the tip of conical carbon protrusions," Applied Physics Letters , vol. 84, no. 19, pp. 3831-3833, 2004.

[31] M. Tanemura, J. Tanaka, K. Itoh, Y. Fujimoto, Y. Agawa, L. Miao, S. Tanemura, "Field electron emission from sputter-induced carbon nanofibers grown at room temperature," Applied Physics Letters , vol. 86, no. 11, pp. 1-3, 2005.

[32] M. Tanemura, T. Okita, J. Tanaka, M. Kitazawa, K. Itoh, L. Miao, S. Tanemura, S. P. Lau, H. Y. Yang, L. Huang, "Room-temperature growth and applications of carbon nanofibers: A review," IEEE Transactions on Nanotechnology , vol. 5, no. 5, pp. 587-593, 2006.

[33] R. C. Che, L.-M. Peng, M. S. Wang, "Electron side-emission from corrugated nanotubes," Applied Physics Letters , vol. 85, no. 20, pp. 4753-4755, 2004.

[34] Y. Saito, S. Uemura, K. Hamaguchi, "Cathode ray tube lighting elements with carbon nanotube field emitters," Japanese Journal of Applied Physics , vol. 37, no. 3, pp. L346-L348, 1998.