Femtosecond laser modification of an array of vertically aligned carbon nanotubes intercalated with Fe phase nanoparticles

Abstract

Femtosecond lasers (FSL) are playing an increasingly important role in materials research, characterization, and modification. Due to an extremely short pulse width, interactions of FSL irradiation with solid surfaces attract special interest, and a number of unusual phenomena resulted in the formation of new materials are expected. Here, we report on a new nanostructure observed after the interaction of FSL irradiation with arrays of vertically aligned carbon nanotubes (CNTs) intercalated with iron phase catalyst nanoparticles. It was revealed that the FSL laser ablation transforms the topmost layer of CNT array into iron phase nanospheres (40 to 680 nm in diameter) located at the tip of the CNT bundles of conical shape. Besides, the smaller nanospheres (10 to 30 nm in diameter) are found to be beaded at the sides of these bundles. Some of the larger nanospheres are encapsulated into carbon shells, which sometime are found to contain CNTs. The mechanism of creation of such nanostructures is proposed.

Labunov et al. Nanoscale Research Letters 2013, 8:375 http://www.nanoscalereslett.com/content/8/1/375

NANO EXPRESS Open Access

Femtosecond laser modification of an array of vertically aligned carbon nanotubes intercalated with Fe phase nanoparticles

Vladimir Labunov1, Alena Prudnikava1*, Serguei Bushuk2, Serguei Filatov3, Boris Shulitski1, Beng Kang Tay4, Yury Shaman5 and Alexander Basaev5

Abstract

Femtosecond lasers (FSL) are playing an increasingly important role in materials research, characterization, and modification. Due to an extremely short pulse width, interactions of FSL irradiation with solid surfaces attract special interest, and a number of unusual phenomena resulted in the formation of new materials are expected. Here, we report on a new nanostructure observed after the interaction of FSL irradiation with arrays of vertically aligned carbon nanotubes (CNTs) intercalated with iron phase catalyst nanoparticles. It was revealed that the FSL laser ablation transforms the topmost layer of CNT array into iron phase nanospheres (40 to 680 nm in diameter) located at the tip of the CNT bundles of conical shape. Besides, the smaller nanospheres (10 to 30 nm in diameter) are found to be beaded at the sides of these bundles. Some of the larger nanospheres are encapsulated into carbon shells, which sometime are found to contain CNTs. The mechanism of creation of such nanostructures is proposed.

Keywords: Femtosecond laser ablation; Carbon nanotube array; Iron phase nanosphere; Chemical vapor deposition

PACS: 61.48.De, 06.60.Jn, 42.62.Cf

Background

Ultrafast lasers are playing an increasingly significant role in materials research, characterization, and surface morphology modification due to a number of unexpected phenomena and formation of new structures. For the past 10 years, being the leading material in semiconductor and photonic industries, silicon has attracted majority of interest and the modification of its surface morphology in different environments using the femtosecond laser (FSL) irradiation has been intensively studied [1-9].

The initial discovery was made when a polished silicon surface was transformed into a forest of quasi-ordered micrometer-sized conical structures upon exposure to several hundred FSL pulses in an atmosphere containing sulfur hexafluoride (SF6) [10,11]. These conical structures

could trap a large quantity of sulfur doping the semiconductor at a concentration that was well above the solubility limit. The confluence of these chemical and structural changes has yielded a unique new material with novel optical properties that have never been observed. This material absorbed about twice as much of visible light as compared to normal silicon and had the ability to detect infrared light that is invisible to the current generation of silicon detectors; also, it possessed significant advantages in detection, imaging, and power generation applications [3,9,12-14]. Lately, various morphology and property changes were reported that have resulted from the FSL irradiation with different varieties of ambient, including various gaseous, as well as vacuum, liquid, water, and air [2,5,6,15-17].

Over the past two decades, carbon nanotubes (CNTs) have attracted a lot of attention due to their exceptional properties [18,19], and as it is expected, potentially, they can replace silicon in the emerging nanoelectronics and nanophotonics.

Hence, investigating the interaction of FSL irradiation with CNTs would represent a great interest. The first

* Correspondence: mailto:[email protected]

Web End [email protected]

Equal contributors

1Laboratory of Integrated Micro- and Nanosystems, Belarusian State University of Informatics and Radioelectronics, P. Brovka St. 6, Minsk 220013, Republic of BelarusFull list of author information is available at the end of the article

2013 Labunov et al.; licensee Springer. This is an Open Access article distributed under the terms of the Creative Commons

Attribution License (http://creativecommons.org/licenses/by/2.0

Web End =http://creativecommons.org/licenses/by/2.0), which permits unrestricted use, distribution, and reproduction

in any medium, provided the original work is properly cited.

Labunov et al. Nanoscale Research Letters 2013, 8:375 Page 2 of 10 http://www.nanoscalereslett.com/content/8/1/375

result that is useful for our investigation was obtained while studying the light interaction with fluffy arrays of single and multiwall CNTs containing metal (Fe) catalyst nanoparticles using a photoflash [20-24]. Photoacoustics and ignition have been observed in these arrays. The mechanism of ignition was attributed to the light absorption by CNT arrays due to the black body effect that generated rapid increase in temperature. As a result, a chain oxidation reaction of CNTs and metal nanoparticles was initiated which caused ignition; as a result of which, nanoparticles containing Fe2O3 and Fe3O4 [24] or C, O, Si, and Fe [23,24] were produced. The most important result of this investigation was that the metal nanoparticles are playing significant role in the deposited energy absorption.

A number of investigations were performed with the laser irradiation of arrays of dense vertically aligned CNTs which have been pursuing the aim of pattering the arrays in order to obtain the configurations of some devices. This process is known as laser pruning [25], burning [26], or laser machining [27]. The lowering of the nanotube density and formation of nanotube junctions and nanoparticles via laser surface treatment were well reported [25-27]. To our best knowledge, only in few works, the femtosecond laser pulses were used for CNT treatment, for example [27,28], while in the rest continuous irradiation of the gas or solid state lasers was utilized [25,26,29,30]. What is important is that in all aforementioned studies, CNT arrays were synthesized by different chemical vapor deposition (CVD) methods, either thermal, hot filament, or plasma enhanced, but in all of them, the localized on the substrate catalysts (Fe or Al/Fe) were used. As a result of this technology utilization, the CNT arrays did not contain metal catalyst nanoparticles. This situation determines the interaction process itself and the obtained products of interaction and could be considered as the simplest case of the laser irradiation interaction with the CNT arrays.

In the present work, we investigate for the first time the interaction of femtosecond laser irradiation with the arrays of vertically aligned carbon nanotubes intercalated with the ferromagnetic (Fe phase) nanoparticles. The presence of metal nanoparticles in CNT array, as it was shown in [20-23], plays the important role in the energy absorption by the array. The importance of the present investigation is defined by the possible applications of the obtained results. The arrays of CNTs with the inter-calated ferromagnetic nanoparticles, so called magnetically functionalized CNTs (MFCNTs) [31,32], may be considered as an ideal medium for different magnetic applications. They can be used as sensors, sensitive elements of magnetometers, magnetic filters, ferrofluids, xerography, magneto-resonance imaging, magnetic hypothermia, and biomedical applications. The superior application of oriented MFCNT arrays can be in a

sphere of magnetic write/read heads and high-density data storage devices [33-36]. The FSL irradiation may become an instrument for the machining of the mentioned devices based on the arrays of MFCNTs.

In particular, in the present work, we investigate the surface morphology modification of the vertically aligned MFCNTs upon FSL irradiation and properties of the products obtained after irradiation and develop the mechanism of the interaction of FSL with such complicated media as the arrays of MFCNTs.

Methods

CNT arrays were synthesized on Si substrates by the floating catalyst CVD via a high-temperature pyrolysis of the xylene/ferrocene solution injected into the reaction zone of quartz reactor. In our particular case, the concentration of ferrocene in the solution was 10%; the temperature in the reaction zone was 875C, and the process duration was 30 s. Obtained as a result of ferrocene decomposition, Fe phase nanoparticles serve as catalyst for CNTs growth. During the growth process, these nanoparticles are intercalating into CNT arrays and are considered as fillers of CNTs.

The morphology of the CNT arrays before and after the FSL irradiation was investigated by scanning electron microscopy (SEM) (Hitachi S-4800 FE-SEM, Chiyoda-ku, Japan). For Raman measurements, Renishaw micro-Raman Spectrometer (Series1000, Renishaw, Wotton-under-Edge, UK) with laser beam of 1.5 mW incident power and 514 nm wavelength was used. The structure of CNTs was characterized by transmission electron microscopy (TEM, JEM 100-CX, JEOL) and a high-resolution TEM (JEM-2010, JEOL Ltd., Akishima-shi, Japan). For X-ray diffraction analysis (XRD), DRON-3 diffractometer (Bourevestnik, Inc., Maloochtinskiy, Russia) was used; the local configurations of iron ions of CNTs fillers were examined with Mssbauer spectroscopy (spectrometer MS2000 with Fe/Rh source, 40 mCu). Elemental analysis was made by energy-dispersive X-ray spectroscopy (EDX) (SUPRA-55WDS with the EDX prefix, Carl Zeiss, Inc., Oberkochen, Germany).

The FSL irradiation was performed in ambient atmosphere with laser scanning microscope (Zeiss LSM 510 NLO based on Zeiss Aviovert 200 M inverted research microscope). This setup is equipped with femtosecond titanium-sapphire laser (Spectra-Physics Tsunami, Santa Clara, CA, USA) delivering 100 fs pulses at a wavelength of 790 nm with 82 MHz repetition rate. The energy of a single pulse was 15 nJ. The laser beam was then focused by Zeiss Plan-Neofluar 40x/0.75 objective and formed a spot with 1.2 m in diameter on the sample surface. The beam was attenuated with an acoustic-optical filter to the energy level of 6.25nJ per pulse at the focal plane of the microscope objective. The investigated samples were

Labunov et al. Nanoscale Research Letters 2013, 8:375 Page 3 of 10 http://www.nanoscalereslett.com/content/8/1/375

placed onto the stage of the microscope without cover glass. CNT array treatment was achieved by scanning line-by-line at 512 lines per scan resolution. The scan speed was about 145 mm/s. The dimension of the scan area could be varied from 230 230 m to 30 30 m. Zoom factor of the microscope was chosen equal or

greater to the required Nyquist criterion to ensure the focal spot overlaps between neighboring lines. Three-dimensional scanning is achieved with a built-in Z-axis drive. The step of Z-axis was chosen to be 1 m, again to ensure the spatial overlapping of the focal spot between neighboring planes.

a

b

1

100 nm

2

c

d

1400

1200

Intensity, a.u.

1000

800

600

400

200

0 0 500 1000 1500 2000

Raman shift, cm-1

e f

70

substrate (400) Si

(002) graphite

60

0,9990

50

(201)Fe 3C

(021)Fe 5C 2

(110)Fe

(211)Fe 3C

(122)Fe 3C

Intensity, a.u.

intensity, a.u.

0,9975

40

(112)Fe 3C

(004)Fe 3C

(222)Fe 3C

0,9960

(313)Fe 3C

0,9945

experiment

total

FeC2 -Fe

Fe3C

-Fe

30

20

10

0,9930

0 20 30 40 50 60 70 80

-6 -4 -2 0 2 4 6

2

velocity, mm s-1

Figure 1 Characteristics of the obtained CNT array grown on Si substrate. (a) Morphology (SEM). (b) TEM image of CNTs with the filler in the CNTs channels (1) and walls (2). (c) HRTEM image of a multiwall CNT with the filler in its channel. (d) Raman spectrum. (e) XRD pattern.(f) Mssbauer spectrum.

Labunov et al. Nanoscale Research Letters 2013, 8:375 Page 4 of 10 http://www.nanoscalereslett.com/content/8/1/375

Results

The characteristic morphology and composition of the obtained CNT array as well as the CNT structure are depicted in Figure 1a,b,c,d,e,f. Figure 1a shows the SEM image of the synthesized dense vertically aligned CNT array. Figure 1b,c shows the TEM images of the synthesized CNTs which are found to be multiwall, with outer diameters of 12 to 70 nm. From Figure 1b, it is seen that some CNTs are filled with nanoparticles (1) in the channels of CNTs and (2) in between their walls. Figure 1d corresponds to the Raman spectrum collected from the sample which contains D peak (approximately 1,358 cm1) arising from the structural disorder and G peak (approximately 1,584 cm1) common to all sp2 carbon forms. The ratio of intensities IG/ID = 2.47 testifies that CNTs are well crystallized and have low defect concentration. The XRD pattern in Figure 1e shows that the CNT array contains graphite (002) with a rhombohedral structure [37] (ICDD card no. 752078, PCPDFWIN), which is a characteristic of CNTs. Besides, the XRD pattern exhibits a series of peaks corresponding to Fe phase (including carbides): Fe3C and Fe5C2. Analysis of the

XRD result reveals that carbide Fe3C with an ortho-rhombic structure (space group Pbnm) dominates over the other phases of nanocomposite (approximately 90%) [32,38]. The Mssbauer spectrum collected in transmission geometry at room temperature is shown in Figure 1f, and the hyperfine parameters (subspectra) are summarized in Table 1. It has been specified that these states of iron are fcc -Fe, bcc -Fe, and Fe3C. However, the spectrum does not reveal the state of Fe5C2 but instead the doublet of FeC2. This discrepancy can be attributed to the difference in sensitivity between the two methods.

A SEM image of the FSL irradiated area of CNT array is presented in Figure 2. The size of the irradiated zone is 200 200 m2 (Figure 2, inset). It can be observed that upon the FSL irradiation, a square cavity of approximately 10 m in depth was created. Nanoparticles of spherical shape were found at the bottom of the cavity located at the tips of conical shape CNT bundles. It is more prominent to observe these nanostructures at the walls of the cavity (indicated as 1 in Figure 2). Also, some of these nanospheres (indicated as 2 in Figure 2) are found to be sited slightly away from the irradiated area.

In Figure 3a, the SEM image of the irradiated area is presented. It is seen that the nanospheres found at the tips of the CNT bundles (1,2) generally have a larger diameters, while those that are found to be beading the CNT bundles (3) have the smaller ones (approximately 10 to 30 nm). From Figure 3a, it is clearly seen that there are two types of larger nanospheres. Some of them are enveloped by the shells of a very complicated structure (2), whereas others do not have shells (2).

In Figure 3b,c, the quantitative analysis on the size distribution of the nanospheres of type (1, 2) is presented. It is seen that these nanospheres have a wide radius distribution (20 to 340 nm) with predominant radius in the range of 30 to 70 nm.

The TEM images are presented in Figure 4a,b,c. In Figure 4a, it can be seen clearly that some of the nanospheres are encapsulated within a shell (1), while some are not (2). Besides, the diameters of CNTs attached to the nanospheres are found to be smaller (approximately 5 nm), as compared to CNTs before laser irradiation (Figure 1b). Smaller nanospheres can also be seen attaching to the outer walls of CNTs (3). Figure 4b represents big size nanospheres covered by the shell (1), which contains some inclusions (2) and a number of easily recognized CNTs (3), whereas in Figure 4c, the magnified image of the nonencapsulated nanosphere is shown.

The EDX spectroscopy was employed in order to obtain a general overview of element distribution in the formed structure (Figure 5a,b,c,d). To have a better understanding within the nanostructure, partial of the CNT array was removed with a high-intensity FSL beam. The corresponding EDX image of the investigated area is shown in Figure 5a. In this figure, dark blue region corresponds to Si substrate, blue corresponds to CNTs, and green represents the nanospheres. Figure 5d shows the EDX spectrum demonstrating signals of Si, O, Fe, and C.

The in-depth quantitative analysis of the elemental composition within the nanosphere was obtained with a localized EDX analysis across its diameter with a 30-nm diameter electron beam spot. In Figure 5b, ten scanning spots across a 600-nm diameter nanosphere are depicted and in Figure 5c, the corresponding EDX analysis plot. It is shown that the composition near to the core of the nanosphere (between 160 and 380 nm of distance) has a higher content of Fe and O as compared to the outer layer of the nanosphere, where C and Si contents are higher. This fact testifies that the nanosphere composition is mainly Fe and O.

Discussion

The removal of the topmost layer of the CNT array and the creation of a cavity upon the FSL irradiation are

Table 1 Hyperfine parameters of the Mssbauer spectrum shown in Figure 1f

Subspectrum eff Contribution Phase

(mm/s) (mm/s) (T)

Singlet 0.13 0 - 20 -Fe

Doublet D 0.20 0.52 - 13 FeC2

Sextet S1 0.17 0 20.6 54 Fe3C

Sextet S2 0.06 0.03 32.6 13 -Fe

Labunov et al. Nanoscale Research Letters 2013, 8:375 Page 5 of 10 http://www.nanoscalereslett.com/content/8/1/375

1

Figure 2 Surface morphology of the FSL irradiated area of the CNT array (SEM). (1) Nanospheres located at the tips of the CNT bundles.(2) Nanospheres located on top of CNT array (outside of the cavity). Inset: the entire 200 200 m2 laser-processed surface.

2

2

a

1

3

Figure 3 SEM images of the nanospheres and their quantitative size distribution. (a) An image of the nanospheres (SEM). (1) A nanosphere without a shell. (2) A nanosphere with the attached CNTs (might be covered with a shell), and (3) the nanospheres beading the CNT bundles.(b) Representative grouping of the nanospheres. (c) Corresponding size distribution.

b

c

Labunov et al. Nanoscale Research Letters 2013, 8:375 Page 6 of 10 http://www.nanoscalereslett.com/content/8/1/375

a

c

1

b

3

1

3

2

2

175 nm

45 nm

100 nm

Figure 4 TEM images of the nanospheres in contact with CNTs in the irradiated area. (a) Nanospheres of larger diameter with (1) and without (2) shells found at the tip of the thinned CNTs, and (3) nanospheres of smaller diameter beading CNTs. (b) Enlarged view of the nanosphere encapsulated into the shell (1) containing some inclusions (2) and CNTs (3). (c) The nanospheres without shells.

achieved by means of ablation. The ultrashort pulse ablation process includes the absorption of optical radiation by bound and free electrons of the material, energy transfer to the lattice, bond breaking, followed by evaporation of the material in a form of atoms or ions, and vapor expansion into an ambient gas. Usually, weak

plasma is formed over the irradiated surface. The sputtered particles, upon losing energy, aggregate into clusters of different sizes, charges, and kinetic energies. These resulting clusters can be either carried away from the reaction zone or re-deposited back onto the target (substrate) surface. This process is known as laser

a

b

200 nm

c

d

keV

Figure 5 EDX spectroscopy data on the composition of the FSL-irradiated CNT array on Si substrate. (a) EDX image of the investigated area. (b, c) Element distribution along the diameter of the nanosphere. (d) EDX spectrum.

Labunov et al. Nanoscale Research Letters 2013, 8:375 Page 7 of 10 http://www.nanoscalereslett.com/content/8/1/375

Figure 6 Schematic of the proposed mechanism of the interaction of the FSL irradiation with CNT arrays.

machining; however, no adequate mechanism for the latter has been proposed.

Here, we propose a basic scheme of formation of the cavity with the observed nanostructures as a result of the interaction of FSL irradiation with the arrays of the vertically aligned CNTs intercalated with Fe phase catalyst nanoparticles. Figure 6 shows the schematic of the proposed mechanism.

In our case, the CNT array represents the target for ablation that consists of two materials, i.e., graphitic CNT walls and various iron phase intercalated within the CNT channels and walls (Figure 6 (1)). Once the ablation threshold is reached, the topmost layer starts to ablate away, i.e., both CNTs and the Fe phase nano-particles. The ablation of the two materials (C and Fe) occurs since the energy density even of a single pulse(0.48 J/cm2) exceeded both of the reported ablation thresholds of various carbonaceous materials (multiwall CNTs, 0.046 J/cm2 [39]; single wall CNTs, 0.05 J/cm2 [40,41]; graphite, 0.13 J/cm2 [42]; graphene, 0.20 J/cm2[43]); and the ablation threshold of iron, 0.18 to0.19 J/cm2 [44,45]. The gradual ablation of the CNT array leads to the formation of the cavity of approximately 10 m depth. This ablation process of the C-Fe target is rather complicated since two distinct materials are being subjected simultaneously to multiple ultrashort laser pulses during 3D scanning. It was found that the mechanism of solid ablation by the intense FSL irradiation is essentially the same [46]. Usually, at atmospheric pressure, the ablation process occurring near to the threshold is always initiated by the ultrafast melting (bonds breaking) of the material, which applies for iron. However, as it was shown by Jeschke's group [47], graphite has the unique property of exhibiting two distinct laser-induced

structural instabilities. At high absorption energies regime (>3.3 eV/atom), nonequilibrium melting occurs that is followed by a fast evaporation. For low intensities, slightly above the damage threshold (>2.0 eV/atom), ablation occurs via removal of intact graphite sheets. Taking into account that the energy density of a single pulse equals to F1 = 0.48 J/cm2, we calculated the absorbed energy per atom E0 using the equation [48]:

F1

eE0nad

1RT ; 1

where e is the Coulomb constant, na is the atomic density, d is the penetration depth of the light, R = 0.3 is the reflectivity, and T = 0 is the transmission of the material which were assumed to be as for graphite [48]. The penetration depth was calculated using the Drude formula d = /4k with the wavelength of 790 nm and extinction coefficient k = 1.5 as for graphite [42]. It has been estimated that the atomic density of our CNT arrays is approximately na = 7.52 1021 atoms/cm3 which is lower than that of the graphite (na = 1.76 1023 atoms/cm3). The calculated value of the absorbed energy per atom even for a single pulse, E0 = 66.95 eV/atom, is much higher than those mentioned in [47] which implies that CNTs in these conditions are burnt instantly.

As a result of C and Fe ablation, localized weak plasma is formed over the irradiated surface (Figure 6 (2)). Both substances exist in their plasma state for a short period of time, while Fe undergoes a rapid condensation and aggregates into spherical clusters (thermodynamically the most favorable shape).

The energy density of the FSL beam, as it is shown in Figure 6, reduces along the depth of CNT array in the

Labunov et al. Nanoscale Research Letters 2013, 8:375 Page 8 of 10 http://www.nanoscalereslett.com/content/8/1/375

process of their interaction. At a certain depth (labeled as II), the energy is not sufficient for the CNT covalent bonds breaking and complete CNTs ablation. Only some of the external walls of the multiwall CNTs are ablated, and this leads to the thinning of the CNTs. The bundling of thinned CNTs into the cones can mainly be caused by the Van der Waals force or/and the magnetic interaction of Fe phase nanoparticles. The Fe phase inclusions located in between the CNT walls most probably have not undergone the complete evaporation but have been subject to a quick melting and resolidification; this led to the formation of smaller nanospheres beading the conical shape of CNT bundles (Figure 6 (3)).

Noteworthy that the Fe phase transformations occur in the presence of carbon atoms and though conditions are quite similar to the floating CVD method, one can suppose that Fe particles can serve as a catalyst for the formation, during the cooling process, of graphitic architectures (shells), covering the iron phase nanospheres. The shells sometime contain CNTs, (Figure 4a,b, Figure 6 (4)). Besides, it was reported that multiwall CNTs and onions had been obtained from graphite in vacuum at 7.5 J/cm2 FSL fluence with the estimated growth time of 1 to 2 ns [49]. Similar to the case of CNTs synthesis process, due to the stochastic process, not all of the catalyst particles facilitate the growth of graphitic shells.

The iron phase nanospheres (with and without shells), after their creation during the first FSL scans, freeze and deposit on the surface of the irradiated area, while some of them are sited slightly away (Figure 2).

During 3D scanning, the Fe-phase nanoparticles that are sited nearer to the tip of the CNTs (labeled as I in Figure 6) would undergo the evaporation process each scan, cluster and re-deposit back mostly on the tips of the CNT conic bundles (Figure 1).

The gradual step-by-step ablation leads to coalescence and increase in the diameter of the nanoparticles formed during the first FSL scans. At a certain diameter of nanospheres, due to Gaussian distribution of laser intensity, the incident energy might be not enough to evaporate the nanospheres completely and they undergo melting instead. Being in a liquid state, they wet the surrounding CNTs. Once the FSL irradiation is stopped, they freeze together forming the observed Fe phase nanosphere/conical CNT bundle nanostructures (Fe/CNT nanostructures), while the graphitic shells (if any) of a very complicated structure (Figure 3a) are being extruded during their cooling (Figure 6 (4)).

This scenario of the Fe/CNT nanostructure shape formation is the most realistic because it clearly explains why in most cases Fe nanospheres are located directly on the tips of the CNT cones. It is worth mentioning, however, that at the beginning, the electrostatic forces between CNTs are responsible for the formation of the

CNT cones structure because sometimes the nanospheres are too small to be able to link the nearby CNTs just by wetting, which was observed in other works also [25].

The described mechanism is the most realistic due to another reason since there is no clear periodicity of the shape of the Fe/CNT nanostructures like, for example, in the case of black silicon where the cone formation is governed by the initial ripple creation with the wavelength close to the central wavelength of the incident laser [7].

Conclusions

In the present work, we investigated for the first time the interaction of FSL irradiation with the arrays of vertically aligned carbon nanotubes intercalated with the ferromagnetic (Fe phase) nanoparticles. The presence of metal nanoparticles in CNT array plays the main role in the energy absorption by the array. As a result of such interaction, a novel composite nanostructured material was obtained. This nanomaterial consists of tiny Fe phase nanospheres attached to the tips of the CNT bundles of conical shape. We designated this material as Fe phase nanosphere/conical CNT bundle nanostructures. The mechanism of such nanostructure formation was proposed. The importance of the present investigation is defined by the possible applications of the obtained results. The arrays of CNTs with the intercalated ferro-magnetic nanoparticles, i.e., MFCNTs, may be considered as an ideal medium for different magnetic applications. The FSL irradiation may become an instrument for the machining of the mentioned devices based on the arrays of MFCNTs. Moreover, one could expect that the obtained nanostructures would possess new optical properties which would find applications in photovoltaics and plasmonics.

AbbreviationsCNT: Carbon nanotube; CVD: Chemical vapor deposition; EDX spectroscopy: Energy-dispersive X-ray spectroscopy; Fe/CNT nanostructures: Fe phase nanosphere/conical CNT bundle nanostructures; FSL: Femtosecond laser; SEM: Scanning electron microscopy;

TEM: Transmission electron microscopy; XRD: X-ray diffraction.

Competing interestsThe authors declare that they have no competing interests.

Authors contributionsVL coordinated the study, analyzed the data, and contributed to the manuscript preparation. AP synthesized the CNT arrays, performed structural analyses of the samples, analyzed the experimental results, and contributed to the manuscript preparation. SB carried out the femtosecond laser irradiation of the CNT arrays and analyzed the data. SF performed EDX study of the irradiated CNTs. BS and BKT analyzed the data and contributed to the manuscript preparation. YS and AB carried out TEM and analyzed the data. All authors read and approved the final manuscript.

AcknowledgementsWe thank the Head of the Government Center BelMicroAnalysis (scientific and technical center Belmicrosystems) V. Pilipenko for the access to SEM facilities (Hitachi S-4800 FE-SEM). We are grateful to J. Fedotova and

Labunov et al. Nanoscale Research Letters 2013, 8:375 Page 9 of 10 http://www.nanoscalereslett.com/content/8/1/375

K. Yanushkevich for providing Mssbauer spectroscopy and XRD diffraction measurements of CNT arrays, correspondingly.

Author details

1Laboratory of Integrated Micro- and Nanosystems, Belarusian State University of Informatics and Radioelectronics, P. Brovka St. 6, Minsk 220013, Republic of Belarus. 2Laboratory of Optical Diagnostics, B.I. Stepanov Institute of Physics of the National Academy of Sciences of Belarus, Minsk 220072, Republic of Belarus. 3Laboratory of Hydrogen Energy, Institute of Heat and Mass Transfer of the National Academy of Sciences of Belarus, Minsk 220072, Belarus. 4School of Electrical and Electronic Engineering, Nanyang Technological University, Singapore 639798, Singapore.

5Scientific-Manufacturing Complex Technological Centre MIET, K-498, Moscow 103498, Russia.

Received: 28 June 2013 Accepted: 22 August 2013 Published: 3 September 2013

References1. Crouch CH, Carey JE, Warrender JM, Aziz MJ, Mazur E, Gnin FY: Comparison of structure and properties of femtosecond and nanosecond laser-structured silicon. Appl Phys Lett 2004, 84:18501852.

2. Shen M, Crouch C, Carey J, Mazur E: Femtosecond laser-induced formation of submicrometer spikes on silicon in water. Appl Phys Lett 2004, 85:56945696.

3. Carey JE, Crouch CH, Shen M, Mazur E: Visible and near-infrared responsivity of femtosecond-laser microstructured silicon photodiodes. Opt Let 2005, 30:17731775.

4. Carey JE III: Femtosecond-laser microstructuring of silicon for novel optoelectronic devices, PhD thesis. Harvard University Cambridge: The Division of Engineering and Applied Sciences; 2004.

5. Crouch C, Carey J, Shen M, Mazur E, Genin F: Infrared absorption by sulfur-doped silicon formed by femtosecond laser irradiation. Appl Phys A: Materials Science & Processing 2004, 79:16351641.

6. Younkin R, Carey J, Mazur E, Levinson J, Friend C: Infrared absorption by conical silicon microstructures made in a variety of background gases using femtosecond-laser pulses. J of Appl Phys 2003, 93:26262629.

7. Tull BR, Carey JE, Mazur E, McDonald JP, Yalisove SM: Silicon surface morphologies after femtosecond laser irradiation. MRS Bull 2006, 31:626633.

8. Zhao J, Wang A: Rear emitter n-type passivated emitter, rear totally diffused silicon solar cell structure. Appl Phys Lett 2006, 88:242102242104.

9. Halbwax M, Sarnet T, Delaporte P, Sentis M, Etienne H, Torregrosa F, Vervisch V, Perichaud I, Martinuzzi S: Micro and nano-structuration of silicon by femtosecond laser: application to silicon photovoltaic cells fabrication. Thin Solid Films 2008, 516:67916795.

10. Her TH, Finlay RJ, Wu C, Deliwala S, Mazur E: Microstructuring of silicon with femtosecond laser pulses. Appl Phys Lett 1998, 73:16731675.11. Her TH, Finlay RJ, Wu C, Mazur E: Femtosecond laser-induced formation of spikes on silicon. Appl Phys A: Materials Science & Processing 2000, 70:383385.

12. Carey JE III, Mazur E: Silicon-based visible and near-infrared optoelectric devices. US Patent number 7057256. US: President & Fellows of Harvard College; 2006.

13. Huang Z, Carey JE, Liu M, Guo X, Mazur E, Campbell JC: Microstructured silicon photodetector. Appl Phys Lett 2006, 89:033506.

14. Myers RA, Farrell R, Karger AM, Carey JE, Mazur E: Enhancing near-infrared avalanche photodiode performance by femtosecond laser microstructuring. Appl Opt 2006, 45:88258831.

15. Wu C, Crouch C, Zhao L, Mazur E: Visible luminescence from silicon surfaces microstructured in air. Appl Phys Lett 2002, 81:19992001.

16. Sheehy MA: Femtosecond-laser microstructuring of silicon: dopants and defects, PhD thesis. Harvard University: The Department of Chemistry and Chemical Biology; 2004.

17. Sheehy MA, Winston L, Carey JE, Friend CM, Mazur E: Role of the background gas in the morphology and optical properties of laser-microstructured silicon. Chem Mater 2005, 17:35823586.

18. Iijima S: Helical microtubules of graphitic carbon. Nature 1991, 354:5658.19. Saito R, Dresselhaus G, Dresselhaus S: Physical Properties of Carbon Nanotubes. London: Imperial College Press; 1998.

20. Ajayan P, Terrones M, De la Guardia A, Huc V, Grobert N, Wei B, Lezec H, Ramanath G, Ebbesen T: Nanotubes in a flash-ignition and reconstruction. Science 2002, 296:705.

21. Bockrath B, Johnson JK, Sholl DS, Howard B, Matranga C, Shi W, Sorescu D: Igniting nanotubes with a flash. Science 2002, 297:192193.

22. Braidy N, Botton GA, Adronov A: Oxidation of Fe nanoparticles embedded in single-walled carbon nanotubes by exposure to a bright flash of white light. Nano Lett 2002, 2:12771280.

23. Tseng SH, Tai NH, Hsu WK, Chen LJ, Wang JH, Chiu CC, Lee CY, Chou LJ, Leou KC: Ignition of carbon nanotubes using a photoflash. Carbon 2007, 45:958964.

24. Cataldo F: A study on the thermal stability to 1000C of various carbon allotropes and carbonaceous matter both under nitrogen and in air. Fullerenes, Nanotubes, Carbon Nanostruct 2002, 10:293311.

25. Lim KY, Sow CH, Lin J, Cheong FC, Shen ZX, Thong JTL, Chin KC, Wee ATS: Laser pruning of carbon nanotubes as a route to static and movable structures. Adv Mater 2003, 15:300303.

26. Hung W, Kumar R, Bushmaker A, Cronin S, Bronikowski M: Rapid prototyping of three-dimensional microstructures from multiwalled carbon nanotubes. Appl Phys Lett 2007, 91:093121093123.

27. Hong NT, Baek IH, Rotermund F, Koh KH, Lee S: Femtosecond laser machining: a new technique to fabricate carbon nanotube based emitters. J Vac Sci Technol B: Microelectron Nanometer Struct 2010, 28:C2B38.

28. Hu A, Peng P, Alarifi H, Zhang X, Guo J, Zhou Y, Duley W: Femtosecond laser welded nanostructures and plasmonic devices. J Laser Appl 2012, 24:042001.

29. Singh G, Rice P, Hurst K, Lehman JH, Mahajan R: Laser-induced exfoliation of amorphous carbon layer on an individual multiwall carbon nanotube. Appl Phys Lett 2007, 91:033101033103.

30. Bhandavat R, Feldman A, Cromer C, Lehman J, Singh G: Very high laser-damage threshold of polymer-derived Si (B) CN-carbon nanotube composite coatings. ACS Appl Mater Interfaces 2013, 5:23542359.

31. Mhl T, Elefant D, Graff A, Kozhuharova R, Leonhardt A, Mnch I, Ritschel M, Simon P, Groudeva-Zotova S, Schneider C: Magnetic properties of aligned Fe-filled carbon nanotubes. J Appl Phys 2003, 93:78947896.

32. Basaev A, Bokhonov B, Demidenko O, Labunov V, Makovetskii G, Prudnikova E, Reznev A, Saurov A, Fedosyuk V, Fedotova YA: Synthesis and properties of magnetically functionalized carbon nanotubes. Nanotechnol in Russia 2008, 3:184190.

33. Gao Y, Bando Y: Nanotechnology: carbon nanothermometer containing gallium. Nature 2002, 415:599. 599.

34. Winkler A, Mhl T, Menzel S, Kozhuharova-Koseva R, Hampel S, Leonhardt A, Buchner B: Magnetic force microscopy sensors using iron-filled carbon nanotubes. J Appl Phys 2006, 99:104905.

35. Mnch I, Leonhardt A, Meye A, Hampel S, Kozhuharova-Koseva R, Elefant D, Wirth M, Bchner B: Synthesis and characteristics of Fe-filled multi-walled carbon nanotubes for biomedical application. J Phys: Conf Ser 2007, 61:820.

36. Zhang X, Wen G, Huang S, Dai L, Gao R, Wang ZL: Magnetic properties of Fe nanoparticles trapped at the tips of the aligned carbon nanotubes.

J Magn Magn Mater 2001, 231:912.

37. Joint Committee on Powder Diffraction Standards: International Center for Diffraction data (JCPDS-ICDD), PCPDFWION, Version 2.00. Newtown Square; 1998.

38. Labunov VA, Shulitski BG, Prudnikava EL, Yanushkevitch KI: Structure, composition and magnetic properties of carbon nanotubes doped by Fe during the growth process. J Phys: Conf Ser 2008, 100:052095.

39. Hashida M, Shimizu S, Sakabe S: Carbon-nanotube cathode modified by femtosecond laser ablation. J Phys: Conf Ser 2007, 59:487.

40. Guo SX, Ben-Yakar A: Femtosecond laser nanoablation of glass in the near-field of single wall carbon nanotube bundles. J Phys D Appl Phys 2008, 41:185306.

41. Lednev VN, Pershin SM, Obraztsova ED, Kudryashov SI, Bunkin AF: Single-shot and single-spot measurement of laser ablation threshold for carbon nanotubes. J Phys D Appl Phys 2013, 46:052002.

42. Reitze D, Ahn H, Downer M: Optical properties of liquid carbon measured by femtosecond spectroscopy. Phys Rev B 1992, 45:2677.

43. Roberts A, Cormode D, Reynolds C, Newhouse-Illige T, Le Roy BJ, Sandhu AS: Response of graphene to femtosecond high-intensity laser irradiation. Appl Phys Lett 2011, 99:051912051913.

Labunov et al. Nanoscale Research Letters 2013, 8:375 Page 10 of 10 http://www.nanoscalereslett.com/content/8/1/375

44. Gamaly E, Luther-Davies B, Kolev V, Madsen N, Duering M, Rode A: Ablation of metals with picosecond laser pulses: evidence of long-lived non-equilibrium surface states. Laser Part Beams 2005, 23:167176.

45. Hirayama Y, Atanasov P, Obara M, Nedialkov N, Imamova S: Femtosecond laser ablation of crystalline iron: experimental investigation and molecular dynamics simulation. Jpn J Appl Phys 2006, 45:792.

46. Gamaly E, Rode A, Luther-Davies B, Tikhonchuk V: Ablation of solids by femtosecond lasers: ablation mechanism and ablation thresholds for metals and dielectrics. Phys Plasmas 2002, 9:949.

47. Jeschke HO, Garcia ME, Bennemann K: Theory for the ultrafast ablation of graphite films. Phys Rev Lett 2001, 87:15003.

48. Jeschke HO, Garcia ME: Theoretical description of the ultrafast ablation of diamond and graphite: dependence of thresholds on pulse duration. Appl Surf Sci 2002, 197:107113.

49. Eliezer S, Eliaz N, Grossman E, Fisher D, Gouzman I, Henis Z, Pecker S, Horovitz Y, Fraenkel M, Maman S: Nanoparticles and nanotubes induced by femtosecond lasers. Laser Part Beams 2005, 23:1519.

doi:10.1186/1556-276X-8-375Cite this article as: Labunov et al.: Femtosecond laser modification of an array of vertically aligned carbon nanotubes intercalated with Fe phase nanoparticles. Nanoscale Research Letters 2013 8:375.

Submit your manuscript to a journal and benet from:

7 Convenient online submission7 Rigorous peer review7 Immediate publication on acceptance7 Open access: articles freely available online 7 High visibility within the eld7 Retaining the copyright to your article

Submit your next manuscript at 7 springeropen.com