Sustainably powering wearable electronics solely by biomechanical energy

Abstract

Harvesting biomechanical energy is an important route for providing electricity to sustainably drive wearable electronics, which currently still use batteries and therefore need to be charged or replaced/disposed frequently. Here we report an approach that can continuously power wearable electronics only by human motion, realized through a triboelectric nanogenerator (TENG) with optimized materials and structural design. Fabricated by elastomeric materials and a helix inner electrode sticking on a tube with the dielectric layer and outer electrode, the TENG has desirable features including flexibility, stretchability, isotropy, weavability, water-resistance and a high surface charge density of 250 μC m^-2 . With only the energy extracted from walking or jogging by the TENG that is built in outsoles, wearable electronics such as an electronic watch and fitness tracker can be immediately and continuously powered.

ARTICLE

Received 20 Apr 2016 | Accepted 28 Jul 2016 | Published 28 Sep 2016

Jie Wang1,2,*, Shengming Li1,*, Fang Yi1,*, Yunlong Zi1, Jun Lin2, Xiaofeng Wang1, Youlong Xu2

& Zhong Lin Wang1,3

Harvesting biomechanical energy is an important route for providing electricity to sustainably drive wearable electronics, which currently still use batteries and therefore need to be charged or replaced/disposed frequently. Here we report an approach that can continuously power wearable electronics only by human motion, realized through a triboelectric nanogenerator (TENG) with optimized materials and structural design. Fabricated by elastomeric materials and a helix inner electrode sticking on a tube with the dielectric layer and outer electrode, the TENG has desirable features including exibility, stretchability, isotropy, weavability, water-resistance and a high surface charge density of 250 mC m 2.

With only the energy extracted from walking or jogging by the TENG that is built in outsoles, wearable electronics such as an electronic watch and tness tracker can be immediately and continuously powered.

DOI: 10.1038/ncomms12744 OPEN

Sustainably powering wearable electronics solely by biomechanical energy

1 School of Materials Science and Engineering, Georgia Institute of Technology, Atlanta, Georgia 30332, USA. 2 Electronic Materials Research Laboratory, Key laboratory of the Ministry of Education & International Center of Dielectric Research, Xian Jiaotong University, Xian 710049, China. 3 Beijing Institute of Nanoenergy and Nanosystems, Chinese Academy of Sciences; National Center for Nanoscience and Technology (NCNST), Beijing 100083, China. * These authors contributed equally to this work. Correspondence and requests for materials should be addressed to Z.L.W. (email: mailto:[email protected]

Web End [email protected] ).

NATURE COMMUNICATIONS | 7:12744 | DOI: 10.1038/ncomms12744 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications 1

ARTICLE NATURE COMMUNICATIONS | DOI: 10.1038/ncomms12744

Wearable electronics, including smart fabrics, wearable light-emitting diodes, health monitoring and motion tracking, are rapidly rising elds in todays

technologies16. From the perspectives of both the practice and aesthetic wearable devices, as well as their power units, are required to be small, lightweight, exible and washable. There has been substantial progresses in reducing the power requirements of devices and increasing the energy densities of batteries, but these systems are still using rigid lithium ion batteries (LIBs) without a self-charging technique; therefore, the batteries are frequently need to be charged or replaced/disposed7. One of the most promising ways to address such issues is the employment of energy-harvesting technologies from the ambient environment for sustainable operation8. There are some possible energy-harvesting power sources, such as solar cells that harvest energy from sunlight and thermoelectric generators that produce electricity from a temperature gradient. However, they cannot ensure a continuous power supply for wearable devices due to the intermittency of sunlight and the low output of thermoelectricity from body heat. Therefore, an energy harvester that works continuously and permits high levels of electrical energy generation is required. To harvest the ubiquitous and constantly available mechanical energy, triboelectric nanogenerators (TENGs) were invented to generate electricity from ambient mechanical motion, such as rotary motion, vibration, oscillating motion and expanding/contracting motion916. Owing to its advantages of light weight, small size, high efciency and a wide choice of materials, TENGs have been utilized for self-charging power systems17, active sensors1820 and sustainable energy sources21. Several studies have been working to harvest energy from body motions in more convenient and efcient ways2225. However, to harvest biomechanical energy as the sustainable source for wearable electronics remains a task to be solved, which would enhance the portability of the wearable electronics, because previous TENGs either failed to come up with sufcient electric output to sustainably power electronic devices or needed to be triggered by other machines17.

In this work, we aim at sustainably powering wearable electronic devices with high-output TENGs and corresponding energy storage units purely by harvesting biomechanical energy from daily motion. To achieve the goal, three principles need to be considered: (1) The TENG in this work should have high output performance; (2) It should be easy for the TENG to harvest biomechanical energy from daily human motions; (3) The self-powered system should be wearable. Therefore, this wearable power source is realized via a TENG with a rationally designed helix-belt contact structure, which is exible, stretchable, weavable, light weight, low cost and water proong. The TENG reveals electrical outputs with a charge density of 250 mC m 2.

The symmetric structure of the tube-like TENG guarantees stable performance when it harvests energy from multiple types of mechanical motion as triggered from various directions. The geometry of the TENG can be tailored to meet customers requests due to its scalable fabrication process. Mounted under shoes or weaved into cloth, the TENG-tubes convert human motion such as walking or jogging into electricity, which immediately and sustainably powers wearable electronics such as an electronic watch and a tness tracker with the combination of a supercapacitor or battery to form a self-charging power system.

ResultsStructure and material design of the TENG. As illustrated in Fig. 1a, the tube-like TENGs are assembled into cloth or shoes to drive wearable electronic devices. The TENG-tubes weaved into

textile have a diameter of 23 mm (Fig. 1b) while the TENG tubes mounted under shoes have a diameter of 67 mm (Fig. 1c). Wearable electronics, such as electronic watch and tness tracker, can be immediately and sustainably powered by the energy generated by the TENG tubes during walking or jogging, without extra power management unit. This achievement is enabled by the high output performance of the TENG tube, which has optimized structure and material designs.

For a TENG, its short-circuit current as well as open-circuit voltage are both proportional to its triboelectric surface charge density; and its output power density is proportional to the square of its triboelectric surface charge density26,27. When the most negative material in the triboelectric series (uorinated ethylene propylene) is utilized as the dielectric material, the measured charge densities are about 20, 40, 80, 134 and 219 mC m 2 with solid gallium, copper, horn-like polypyrrole (hPPy), liquid galinstan and liquid gallium serving as the counter partner material, respectively2830. It can be seen that liquid metal leads to the highest output, followed by the exible nanomaterial, then the solid metal. This phenomenon indicates that besides the distinction between the electron afnities of two triboelectric materials, the effectiveness of contact between two triboelectric surfaces also plays an important role in charge density enhancement. It has been found that an effective charge transfer process for contact electrication occurs when the contact distance between two surfaces is around intermolecular distance31. Therefore, the soft and exible contact surfaces help improve the area for charge transfer in comparison with coarse solid surface, which is the foundation for the high output of the as-fabricated TENG in material aspect.

The detailed structure of the as-fabricated TENG is shown in Fig. 1d, e. It can be seen that the TENG is basically composed of two parts. One part is the dielectric layer and its back electrode (outer electrode), shaping into a tube. The other part is the belt-like inner electrode, which attaches to the interior surface of the tube and forms a helix extending along the inside of the tube. The two triboelectric parts are wrapped in another dielectric layer that protects them from contamination. The dielectric layer is made from silicone rubber, which has a strong tendency to gain electrons and possesses excellent exibility and stretchability in all dimensions. The outer and inner electrodes are prepared from the mixture of silicone rubber, carbon black and carbon nanotubes (CNTs; Fig. 1f), which electric conductivity is 4.3 S m 1 and stretchability limit is 620% (Supplementary Fig. 1). The carbon black provides the basic conductivity; while the CNTs not only further enhances the conductivity due to its good conductivity under high strain but also enlarges the contact area by forming nanostructured surface32. Such rubber-based soft material endows the triboelectric layers with high contact intimacy.

Working mechanism and electrical outputs of the TENG. The working mechanism of the TENG-tube is briey presented in Fig. 2a, which is based on a coupling of triboelectric effect and electrostatic induction33. When the tube is compressed, the inner electrode comes to contact with the dielectric layer. Since the dielectric layer has a higher ability to attract electrons, electrons on the inner electrode surface will transfer to the surface of the dielectric layer, resulting in a negatively charged dielectric layer surface and a positively charged inner electrode surface (i). Note that the triboelectric charges on the dielectric layer surface will be retained for a long period of time due to the nature of electrets. Once released, positive charges are induced on the outer electrode(ii); then electrons will ow from the outer electrode to the inner electrode through the load and nally reach an equilibrium (iii). As compressed again, electrons will ow back from the inner

2 NATURE COMMUNICATIONS | 7:12744 | DOI: 10.1038/ncomms12744 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications

NATURE COMMUNICATIONS | DOI: 10.1038/ncomms12744 ARTICLE

a b

d e

Inner electrode

Surface

Outer electrode

Dielectric layer

c

f

Figure 1 | Overview of the TENG. (a) TENG weaved into a coat and assembled under shoes to drive wearable electronics such as an electronic watch and a tness tracker. (b) Photograph showing TENG tubes in diameter of 23 mm weaved into textile. (c) Photograph showing TENG-tubes xed under a shoe. (d) Structure sketch of the TENG tubes. (e) Enlarged view of the TENG structure. (f) SEM image of the triboelectric electrode surface. Theinset shows the SEM image of the carbon black/CNTs mixture, which is the conductive ingredient of the inner and outer electrodes. Scale bars in b,f and the inset in f are 1 cm, 5 mm and 500 nm, respectively.

electrode to the outer electrode (iv) and ultimately reach a new balance, until the inner electrode contacts the dielectric layer again (i). Thus, alternative current can be produced via periodically compressing and releasing of TENG tube.

The surface charge density (sSC) of the helix-belt structured TENG tube is boosted to be about 250 mC m 2. This value is among the highest values reported2830 and is the basis of high output performance of TENG because it improves the energy harvested per operation cycle with higher short circuit current. Here the charge density of the helix-belt structured TENG is calculated by dividing the charges by the actual contact area of the inner electrode, which is only part of the total area of the inner electrode. This is because that there is a partial overlap of the helix inner electrode when the TENG is pressed at and therefore the actual contact area is smaller. The detailed calculation for the contact area can be found in Supplementary Fig. 2 and Supplementary Note 1. Apart from the material aspect discussed above, it is found that the helix structure of the inner electrode has a considerably higher charge density than that of the traditional straight-layout structured TENG (Fig. 2d), which is only 110 mC m 2 given the same size for contact areas. We have proceeded verifying experiments using the basic contact-separation TENG with the same materials to explore the reason for this difference. It is demonstrated that when the contact area enlarges, the transported charges slowly increase but the charge density drastically declines, with the charge density reaching to B250 mC m 2 when the size of the contacting surfaces is decreased to 5 5 mm2 (Supplementary Fig. 3 and

Supplementary Note 2). This indicates that the helix inner electrode is benecial for high charge density by dividing one larger area as a whole into several smaller ones when compressed. This might be due to the improved contact effectiveness of the surfaces with the smaller size. And besides, when pressed from various directions, the helix-belt structured TENG presents a steady charge density (the red curve in Fig. 2e); while the straight-layout structured TENG shows an output that is direction sensitive, which even drops to zero when the oblique angle of the electrode to horizontal axis (y) is 90o (the blue curve in Fig. 2e).

The constant performance of the helix-belt structured TENG can be attributed to the fact that its symmetric structure results in an invariant contact area at different pressing directions.

To obtain an optimized charge density of the helix-belt structured TENG tube, three geometry parameters are introduced, namely the width of the inner electrode belt d, the oblique angle of the belt to horizontal axis y, and the width of the tube when it is attened, D, that is, the half of its perimeter. Since the output surface charge (QSC) of a TENG usually increases with the contact area (Supplementary Fig. 3), the charge density is commonly used to compare the performance among TENGs. For the helix-belt structured TENG tube, once its total size is settled, it is ideal to achieve a maximal output charge coupled with the highest charge density through adjusting the geometry parameters. It is found that when d remains at a constant value of 5 mm, the highest charge and charge density are simultaneously acquired at y 45 (Fig. 2f, g). When y is set to be 45 (Fig. 2h, i),

with the increase of d, the transferred charges increases rst and then decreases, which is because part of the dielectric lm is left untouched when d is too small while part of the inner electrode is overlapping when d is too large. The charges density decreases with the increasing d, and the optimal d for charge and charge density is 5 mm for the TENG-tube with a determined size (Fig. 2j, k), where the obtained charge is 100 nC and charge density is 250 mC m 2. Consequently, a relationship among these three parameters for an optimal performance of the helix-belt structured TENG can be derived, which is d D sin y.

Extracting energy from diverse motion by the TENG. Since the helix-belt structured TENG tube has excellent stretchability; besides the pressing motion, it can also harness energy from various other types of motion such as bending motion, twisting motion and lengthening motion. Figure 3 exhibits the test results of the helix-belt structured TENG (diameter: 7 mm) when harvesting energy in such kinds of motion. For the pressing motion (Fig. 3ac), the charge density (B250 mC m 2) and the peak value of the open-circuit voltage (B145 V) remain unchanged under different frequencies; while the peak value of

NATURE COMMUNICATIONS | 7:12744 | DOI: 10.1038/ncomms12744 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications 3

ARTICLE NATURE COMMUNICATIONS | DOI: 10.1038/ncomms12744

a b

This work

Gallium (L)

Galistan (L)

iv

i

i

250

200

i

Compressing

SC(C m2)

SC(C m2)

150

iii

Inner electrode (facing up)

Inner electrode (facing down)

Dielectric layer Outer electrode Surface

Contact region

ii

100 LM-TENG

Compressed

hPPy

Released

50

300

150

0

hPPy-TENG

Helix

Straight

Cu

0 Gallium (S)

Releasing

c d e

0 45 45

90 90

0

0 30 60 90 ()

f h j

Different , constant d

d = 5 mm

Different d, constant

d = D sin

d D

g i k

120

110

100

90

280

240

200

160

120

260

200

100

= 45 d = D sin

240

Q SC(nC)

220

180

160

SC(C m2)

Q SC(nC)

90

70

60

80

SC(C m2)

Q SC(nC)

140

120

100

80 3 4 5 6 7

280

240

200

160

SC(C m2)

80

70

20

30

40

50

60

70

80

90

3 4 5 6 7

()

d (mm) d (mm)

Figure 2 | Working mechanism and output performance of the TENG. (a) Working mechanism of the TENG. (b) Comparison of the output charges density (ssc) measured in this work with that in the previous works, insets in top-left corner and bottom-right corner show the structure of liquid-metal based triboelectric nanogenerator (LM-TENG) and horn-like polypyrrole based triboelectric nanogenerator (hPPy-TENG), respectively. (c,d) Schematic diagrams of the helix-belt structured TENG and the straight-layout structured TENG pressed at various directions. (e) ssc of the helix-belt structured TENG and straight-layout structured TENG. (fk) Schematic diagram and output charge (QSC) and ssc of the TENG at various structure parameters, and the error bars are s.d.: (f,g) width of the triboelectric electrode (d) is 5 mm; (h,i) oblique angle of the electrode to horizontal axis (y) is 45; (j,k) d D siny, where

D is the width of the tube when it is attened by pressing.

the short-circuit current density increases with the frequency, from 5 mA m 2 at 2 Hz to 16 mA m 2 at 10 Hz. Note that for the helix-belt structured TENG with the optimized geometry parameters as discussed above, when its total size further scales

down, the output charges will vary but the output charge density will be maintained. For example, the output charges of a TENG tube with a diameter of 3 mm drops to 45 nC but the charge density still remains around 250 mC m 2 (Supplementary Fig. 4).

4 NATURE COMMUNICATIONS | 7:12744 | DOI: 10.1038/ncomms12744 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications

NATURE COMMUNICATIONS | DOI: 10.1038/ncomms12744 ARTICLE

a b c

2 Hz 5 Hz 10 Hz 8 Hz

2 Hz 5 Hz 10 Hz 8 Hz

10 2 Hz

5 Hz

8 Hz

10 Hz

SC(C m2)

200

100

300 160 20

10

I SC(mA m2)

V OC(V)

120

80

40

0

0

0

0

20

5 10 15 20 25 t (s)

0 5 10 15 20 25 t (s)

0 5

10 15 20

Bending Twisting Lengthening

25

t (s)

d

f

h

e

g

i

8

6

180

6

90

12

16

8

270

Q SC(nC)

4

2

0

180

100%

150%

4

2

0

45

Q SC(nC)

Q SC(nC)

90

50%

4

0

Figure 3 | Electrical outputs of the TENG on diverse types of motions. (ac) (a) Charge density (ssc), (b) open-circuit voltage (VOC) and (c) short-circuit current (ISC) of the TENG at various pressing frequencies. (di) Working mechanism and output charge (QSC) of the TENG (d,e) under bending motion, (f,g) under twisting motion, (h,i) under lengthening motion.

The output charges can be linearly boosted by using multiple TENG tubes in parallel (Supplementary Fig. 5), for example, four TENG tubes generate a charge of 400 nC from the pressing motion. In addition, the TENG presents excellent performance stability, with its charge density, open-circuit voltage and short-circuit current maintaining steady after 3 million cycles of operation at a contact frequency of 10 Hz (Supplementary Fig. 6). These properties enable the TENG tubes to be an effective congurable power source such as the energy shoes by assembling TENG tubes under/inside the shoes.

For the bending and twisting motion, the resulted deformation of the TENG tube is similar to the deformation caused by localized pressing. When bended from 45 to 180, the charge of the TENG tube increases from 2 to 5.2 nC (Fig. 3d, e), while the open-circuit voltage increases from 10 to 25 V and the short-circuit current increases from 10 to 30 nA (Supplementary Fig. 7a,b). When twisted from 90 to 270, the charge grows from 2 to 6 nC (Fig. 3f, g), while the open-circuit voltage increases from 10 to 30 V and the short-circuit current increases from 10 to 45 nA (Supplementary Fig. 7c,d). For the stretching motion, the tube length increases and the tube diameter decreases periodically. The charges increase from 4 to 12.5 nC as the tensile strain increases from 50 to 150%, while the open-circuit voltage increases from 20 to 63 V and the short-circuit current increases from 20 to 70 nA (Supplementary Fig. 7e,f).

Applications of the TENG in wearable electronics. The ability of accommodating to curvilinear surface and harvesting energy from diverse motion makes the helix-belt structured TENG-tube a desirable wearable power source. Moreover, since the TENG-tube is well packaged with a layer of silicone rubber, it is light-weight, waterproong and anticorrosive, which can better suit the practical needs compared with traditional wearable power sources based on solid materials like metal. When immersed and swayed in water, the TENG tube maintains its high output charge density, and one single tube can sufciently light up 32 light-emitting diodes (LEDs) by manually tapping it after taken out of water (Fig. 4a and Supplementary Video 1). When weaving 8 TENG-tubes in parallel into a shoe sole or a safety vest, LED warning signs on the vest such as CAUTION, PASS, and STOP can be lighted up during walking or tapping the vest (Fig. 4b,c, Supplementary Video 2). The TENG tubes can be further integrated with a supercapacitor/LIB to form a self-charging power system (Fig. 4d). Note that when the power system is utilized to directly drive electronics, a certain number of TENG tubes can be employed according to the load of the electronics. Pressing by hand, it takes 70 s for 2 TENG tubes to charge the supercapacitor with the horn-like polypyrrole active material of0.008 mg from 0 to 70 mV (Fig. 4e), where the equivalent galvanostatic current can be calculated as 1.4 mA (Supplementary

Note 3). The morphology of horn-like polypyrrole and the

NATURE COMMUNICATIONS | 7:12744 | DOI: 10.1038/ncomms12744 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications 5

ARTICLE NATURE COMMUNICATIONS | DOI: 10.1038/ncomms12744

a b c

Before washing After washing

SC(C m2)

400 300 200 100

0

0 5 10 15 20

d e f

0.080.060.04

TENG

Load

V

Rectifier

t (s)

LIB

/SC

V(V)

0.020.00

0 20 40 60 80

K1 K2

t (s)

Figure 4 | Applications of the TENG in emergency response and weather indication. (a) Charge density of the TENG before and after washing in water. The left insert showing the TENG immerged into water, and the right insert showing that 32 LEDs were lighted by pressing the TENG after washed in water. (b,c) LED warning signs on a vest, i.e., CAUTION, PASS and STOP are lighted by pressing the TENG weaved into the vest. (d) Circuit diagram of the self-charging power system integrated by the TENG and SC/LIB. (e) Charging curve of SC by manually pressing two TENG-tubes. (f) A temperature-humidity meter is driven by manually tapping ve parallel TENG tubes.

2.70

2.65

2.60

a c e

b d f

3.765

3.760

3.755

3.750

Walking

0 50 100 150 200

Rest

Running

V(V)

V(V)

0 10 20 30 40 50 60 70

t (s)

t (s)

Figure 5 | Sustainably powering wearable electronics during walking or jogging. (a) Image of the energy-shoe. (b) Image of the energy-outsole. (c) An electronic watch is driven and (d) LIB in the self-charging power system is charged simultaneously by the energy-shoe while walking.(e) A tness tracker is driven and (f) LIB is charged simultaneously by the energy-shoe when jogging.

chargingdischarging curve of the supercapacitor are presented in Supplementary Figs 8 and 9. A temperaturehumidity meter can be driven by manually tapping 5 TENG tubes connected in parallel (Fig. 4f, Supplementary Video 3).

With 40 tubes assembled under a pair of shoes (Fig. 5a), an electronic watch and tness tracker called up move can be immediately and sustainably powered sorely by walking and jogging (Fig. 5cf). Note that the original batteries of the two electronic devices are replaced in advance by a home-made LIB with the LiMn2O4 active material of 0.5 mg that is specially designed for the TENG to ensure a fast charging rate. The morphology and X-ray diffraction pattern of LiMn2O4 is

presented in Supplementary Fig. 10 and the chargingdischarging

curve of the LIB is presented in Supplementary Fig. 11. While walking, the voltage of the battery keeps growing at the same time the electronic watch is powered, which indicates that the TENG tubes produces sufcient amount of energy to charge the LIB in addition to sustaining the consumption of the electronic watch (Fig. 5d, Supplementary Video 4). Once motion stopped, the voltage begins to decline as the LIB is discharged. The tness tracker is driven by jogging, the self-charging power system is also able to support the electronic device and charge the LIB simultaneously (Fig. 5f, Supplementary Video 5). When the LIB is charged by pressing ve TENG tubes connected in parallel at10 Hz with a shaker, its voltage increases from 2.8 to 4.2 V during 7 h (Supplementary Fig. 11).

6 NATURE COMMUNICATIONS | 7:12744 | DOI: 10.1038/ncomms12744 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications

NATURE COMMUNICATIONS | DOI: 10.1038/ncomms12744 ARTICLE

DiscussionIn summary, a sustainable operation of wearable electronics is achieved by a material-and-structure optimized TENG, which produces sufcient energy by converting human motion into electricity. From the structural aspect, the TENG adopts a rationally designed helix-belt structure that boosts the performance by dividing the electrode into several small areas for more sufcient contact, with a charge density of 250 mC m 2, which is among the highest reported to the best of our knowledge.

Moreover, the helix-belt structured TENG is symmetric, which endows it with stable performance when triggered from various directions. From the material aspect, the rubber-based materials makes the TENG highly stretchable, light weight, anticorrosive and it can effectively extract energy from multiple deformations involving pressing, stretching, bending and twisting. The TENG is also waterproof and exhibits steady performance after being washed. Due to its potentially scalable fabrication process, the size of the TENG can be altered easily to t various applications. The TENG may be applied for emergency response or weather indications by lighting up LED signs on a safety vest or driving a temperaturehumidity meter with the energy harnessed from human motion. When integrated in a self-charging power system with a supercapacitor or LIB, a pair of outsoles assembled with the TENG can immediately and sustainably drive electronic devices such as an electronic watch and tness tracker, where the energy harvested from only walking and jogging can simultaneously drive the wearable electronic device and charge the battery. This work may represent an advance in the development of wearable power sources and could offer new design options for self-powered systems.

Methods

Fabrication of the TENG. The liquid silicone rubber was obtained by mixing the base and cure (1:1 by volume ratio) of the silicone rubber (Ecoex 0030) in a beaker, then it was added the mixture of conductive carbon black and CNTs (2:1, weight ratio). After they were mixed uniformly, carbon black/CNTs@silicone rubber, was smeared over a piece of acrylic plate preprocessed with a release agent and cured at a temperature of 30 C for 5 h, a soft conductive electrode was obtained. The conductive electrode can be used as not only triboelectric electrode after it was cut to belts with a width of 5 mm, but also back electrode after it was coated by the silicone rubber as dielectric layer.

Fabrication of the supercapacitor and LIB. The supercapacitor is fabricated to be symmetrical structure, with two identical micro/nano-structured hPPy electrodes as positive and negative electrodes, and 1 M KCl aqueous solution as electrolyte. The synthesis process of the hPPy is discussed in Supplementary Note 4. The supercapacitor was packaged by two pieces of Kapton lms in sandwich structure. In the LIB, LiMn2O4 is used as positive electrode active material and graphiteas negative electrode material, with 1 M LiPF6 in ethylene carbonate/diethyl carbonate/dimethyl carbonate (EC/DEC/DMC 1:1:1 by weight ratio) as electrolyte. For fabrication of LiMn2O4 electrodes, the prepared powders were mixedwith carbon black and polyvinylidene uoride (70:20:10 by weight ratio) in N-methylpyrrolidinon. The slurry thus obtained was coated onto Al foil and then dried at 120 C overnight in vacuum condition. The graphite negative electrode with copper as current collector was obtain from commercial sources and was used as received. The battery is packaged to be 2016 type coin cells with porous polyethylene lm as separator. The synthesis process of LiMn2O4 is depicted in

Supplementary Note 5.

Data availability. The data supporting the ndings of this study is available from the corresponding author on request.

References

1. Gao, W. et al. Fully integrated wearable sensor arrays for multiplexed in situ perspiration analysis. Nature 529, 509514 (2016).

2. Lee, H. et al. A graphene-based electrochemical device with thermoresponsive microneedles for diabetes monitoring and therapy. Nat. Nanotechnol. 11, 566574 (2016).

3. Choi, M. K. et al. Wearable redgreenblue quantum dot light-emitting diode array using high-resolution intaglio transfer printing. Nat. Commun. 6, 7149 (2015).

4. Yokota, T. et al. Ultraexible organic photonic skin. Sci. Adv. 2, e1501856 (2016).

5. Cima, M. J. Next-generation wearable electronics. Nat. Biotechnol. 32, 642643 (2014).

6. Son, D. et al. Multifunctional wearable devices for diagnosis and therapy of movement disorders. Nat. Nanotechnol. 9, 397404 (2014).

7. Larcher, D. & Tarascon, J. M. Towards greener and more sustainable batteries for electrical energy storage. Nat. Chem. 7, 1929 (2015).

8. Wang, S. et al. Motion charged battery as sustainable exible-power-unit. ACS Nano 7, 1126311271 (2013).

9. Zi, Y. et al. Triboelectric-pyroelectric-piezoelectric hybrid cell for high-efciency energy-harvesting and self-powered sensing. Adv. Mater. 27, 23402347 (2015).

10. Guo, H. et al. An ultrarobust high-performance triboelectric nanogenerator based on charge replenishment. ACS Nano 9, 55775584 (2015).

11. Zheng, L. et al. A hybridized power panel to simultaneously generate electricity from sunlight, raindrops, and wind around the clock. Adv. Energy Mater. 5, 1501152 (2015).

12. Yi, F. et al. Stretchable-rubber-based triboelectric nanogenerator and its application as self-powered body motion sensors. Adv. Funct. Mater. 25, 36883696 (2015).

13. Yi, F. et al. Self-powered trajectory, velocity, and acceleration tracking of a moving object/body using a triboelectric sensor. Adv. Funct. Mater. 24, 74887494 (2014).

14. Lee, K. Y., Gupta, M. K. & Kim, S. W. Transparent exible stretchable piezoelectric and triboelectric nanogenerators for powering portable electronics. Nano Energy 14, 139160 (2015).

15. Wang, J. et al. A exible ber-based supercapacitor-triboelectric-nanogenerator power system for wearable electronics. Adv. Mater. 27, 48304836 (2015).16. Cheng, X. et al. Wearable electrode-free triboelectric generator for harvesting biomechanical energy. Nano Energy 12, 1925 (2015).

17. Zhu, G., Chen, J., Zhang, T., Jing, Q. & Wang, Z. L. Radial-arrayed rotary electrication for high performance triboelectric generator. Nat. Commun. 5, 3426 (2014).

18. Jing, Q., Xie, Y., Zhu, G., Han, R. P. S. & Wang, Z. L. Self-powered thin-lm motion vector sensor. Nat. Commun. 6, 8031 (2015).

19. Wang, S., Lin, L. & Wang, Z. L. Triboelectric nanogenerators as self-powered active sensors. Nano Energy 11, 436462 (2015).

20. Meng, B. et al. A transparent single-friction-surface triboelectric generator and self-powered touch sensor. Energy Environ. Sci. 6, 32353240 (2013).

21. Niu, S., Wang, X., Yi, F., Zhou, Y. S. & Wang, Z. L. A universal self-charging system driven by random biomechanical energy for sustainable operation of mobile electronics. Nat. Commun. 6, 8975 (2015).

22. Donelan, J. M. et al. Biomechanical energy harvesting: generating electricity during walking with minimal user effort. Science 319, 807810 (2008).

23. Kim, S. J., We, J. H. & Cho, B. J. A wearable thermoelectric generator fabricated on a glass fabric. Energy Environ. Sci. 7, 19591965 (2014).

24. Lee, S., Lee, Y., Park, J. & Choi, D. Stitchable organic photovoltaic cells with textile electrodes. Nano Energy 9, 8893 (2014).

25. Pu, X. et al. A self-charging power unit by integration of a textile triboelectric nanogenerator and a exible lithium-ion battery for wearable electronics. Adv. Mater. 27, 24722478 (2015).

26. Zi, Y. et al. Standards and gure-of-merits for quantifying the performance of triboelectric nanogenerators. Nat. Commun. 6, 8376 (2015).

27. Wang, S. et al. Maximum surface charge density for triboelectric nanogenerators achieved by ionized-air injection: methodology and theoretical understanding. Adv. Mater. 26, 67206728 (2014).

28. Wang, J. et al. All-plastic-materials based self-charging power system composed of triboelectric nanogenerators and supercapacitors. Adv. Funct. Mater. 26, 10701076 (2016).

29. Wang, J. et al. Self-powered electrochemical synthesis of polypyrrole from pulsed output of triboelectric nanogenerator as a sustainable energy system. Adv. Funct. Mater. 26, 35423548 (2016).

30. Wang, S. et al. Molecular surface functionalization to enhance the power output of triboelectric nanogenerators. J. Mater.Chem. A 4, 37283734 (2016).

31. Li, S. et al. Excluding contact electrication in surface potential measurement using kelvin probe force microscopy. ACS Nano 10, 25282535 (2016).

32. Frank, S., Poncharal, P., Wang, Z. L. & de Heer, W. A. Carbon nanotube quantum resistors. Science 280, 17441746 (1998).

33. Wang, Z. L., Chen, J. & Lin, L. Progress in triboelectric nanogenerators as a new energy technology and self-powered sensors. Energy Environ. Sci. 8, 22502282 (2015).

Acknowledgements

This work was supported by the Hightower Chair Foundation, the Thousands Talents program for a pioneer researcher and his innovation team and National Natural Science Foundation of China. (21274115).

NATURE COMMUNICATIONS | 7:12744 | DOI: 10.1038/ncomms12744 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications 7

ARTICLE NATURE COMMUNICATIONS | DOI: 10.1038/ncomms12744

Author contributions

J.W., S.L., F.Y. and Z.L.W. conceived the idea, analysed the data and wrote the paper. J.W. and F.Y. designed the materials of the triboelectric nanogenerators. J.W. andS.L. optimized the structure of the triboelectric nanogenerators. Y.L. derived the theories for structure optimization. J.L. and Y.X. fabricated the supercapacitor and lithium ion battery. X.W. helped with the experiments. All the authors discussed the results and commented on the manuscript.

Additional information

Supplementary Information accompanies this paper at http://www.nature.com/naturecommunications

Web End =http://www.nature.com/ http://www.nature.com/naturecommunications

Web End =naturecommunications

Competing nancial interests: The authors declare no competing nancial interests.

Reprints and permission information is available online at http://npg.nature.com/reprintsandpermissions/

Web End =http://npg.nature.com/ http://npg.nature.com/reprintsandpermissions/

Web End =reprintsandpermissions/

How to cite this article: Wang, J. et al. Sustainably powering wearable electronics solely by biomechanical energy. Nat. Commun. 7:12744 doi: 10.1038/ncomms12744 (2016).

This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the articles Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/

Web End =http://creativecommons.org/licenses/by/4.0/

r The Author(s) 2016

8 NATURE COMMUNICATIONS | 7:12744 | DOI: 10.1038/ncomms12744 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications