Growing three-dimensional biomorphic graphene powders using naturally abundant diatomite templates towards high solution processability

Abstract

Mass production of high-quality graphene with low cost is the footstone for its widespread practical applications. We present herein a self-limited growth approach for producing graphene powders by a small-methane-flow chemical vapour deposition process on naturally abundant and industrially widely used diatomite (biosilica) substrates. Distinct from the chemically exfoliated graphene, thus-produced biomorphic graphene is highly crystallized with atomic layer-thickness controllability, structural designability and less noncarbon impurities. In particular, the individual graphene microarchitectures preserve a three-dimensional naturally curved surface morphology of original diatom frustules, effectively overcoming the interlayer stacking and hence giving excellent dispersion performance in fabricating solution-processible electrodes. The graphene films derived from as-made graphene powders, compatible with either rod-coating, or inkjet and roll-to-roll printing techniques, exhibit much higher electrical conductivity (∼110,700 S m^-1 at 80% transmittance) than previously reported solution-based counterparts. This work thus puts forward a practical route for low-cost mass production of various powdery two-dimensional materials.

ARTICLE

Received 25 May 2016 | Accepted 3 Oct 2016 | Published 7 Nov 2016

Ke Chen1,2, Cong Li1,3, Liurong Shi1, Teng Gao1,w, Xiuju Song1, Alicja Bachmatiuk4,5, Zhiyu Zou1, Bing Deng1, Qingqing Ji1, Donglin Ma1, Hailin Peng1, Zuliang Du2, Mark Hermann Rmmeli4,5,6, Yanfeng Zhang1,3& Zhongfan Liu1

Mass production of high-quality graphene with low cost is the footstone for its widespread practical applications. We present herein a self-limited growth approach for producing graphene powders by a small-methane-ow chemical vapour deposition process on naturally abundant and industrially widely used diatomite (biosilica) substrates. Distinct from the chemically exfoliated graphene, thus-produced biomorphic graphene is highly crystallized with atomic layer-thickness controllability, structural designability and less noncarbon impurities. In particular, the individual graphene microarchitectures preserve a three-dimensional naturally curved surface morphology of original diatom frustules, effectively overcoming the interlayer stacking and hence giving excellent dispersion performance in fabricating solution-processible electrodes. The graphene lms derived from as-made graphene powders, compatible with either rod-coating, or inkjet and roll-to-roll printing techniques, exhibit much higher electrical conductivity (B110,700 S m 1 at 80%

transmittance) than previously reported solution-based counterparts. This work thus puts forward a practical route for low-cost mass production of various powdery two-dimensional materials.

1 Center for Nanochemistry (CNC), Beijing Science and Engineering Research Center for Nanocarbons, Beijing National Laboratory for Molecular Sciences, State Key Laboratory for Structural Chemistry of Unstable and Stable Species, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871, China. 2 Key Laboratory for Special Functional Materials (Ministry of Education), Henan University, Kaifeng 475004, China. 3 Department of Materials Science and Engineering, College of Engineering, Peking University, Beijing 100871, China. 4 Centre of Polymer and Carbon Materials, Polish Academy of Sciences,M. Curie-Sklodowskiej 34, Zabrze 41-819, Poland. 5 IFW Dresden, 20 Helmholtz Strasse, Dresden 01069, Germany. 6 School of Energy, Soochow University, Suzhou 215006, China. w Present address: Department of Chemistry and Chemical Biology, Harvard University, Cambridge, Massachusetts 02138, USA.

Correspondence and requests for materials should be addressed to Y.Z. (email: mailto:[email protected]

Web End [email protected] ) or to Z.L. (email: mailto:[email protected]

Web End [email protected] ).

NATURE COMMUNICATIONS | 7:13440 | DOI: 10.1038/ncomms13440 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications 1

DOI: 10.1038/ncomms13440 OPEN

Growing three-dimensional biomorphic graphene powders using naturally abundant diatomite templates towards high solution processability

ARTICLE NATURE COMMUNICATIONS | DOI: 10.1038/ncomms13440

One of the keys for determining the industrial future of graphene material is its mass production technology with high quality and low cost14. Currently, there are two

typical routes for the scalable production of graphene, giving graphene powders or lms510. The graphene powders are usually synthesized from graphite powders based on wet chemistry approaches, including reduced graphene oxide (RGO) and liquid-phase exfoliated graphene (LPEG)11,12. The production ability of such chemically exfoliated graphene powders has reached up to a level of kilotons per year with relatively low cost. However, the chemically exfoliated graphene materials are generally rich of structural defects and chemical residues such as OH, C O,

COOH and other noncarbon impurities, which undesirably lose the fascinating properties of pristine graphene1315. The homogeneous high-concentration dispersion of such graphene powders in solution is still of great technical challenge due to the strong pp stacking interactions16 between planar graphene sheets. This severely limits their solution processability and retards various applications of graphene powders.

Another route to mass production relies on chemical vapour deposition (CVD) techniques, which generate high-quality graphene lms8,9,1719. The current CVD graphene lms grown on catalytic metal surfaces have become competitive in crystallinity with mechanically exfoliated graphene, together with sub-million square metres per year yield. Such kinds of high-quality graphene lms would nd wide applications in electronic and optoelectronic devices20,21. However, these graphene lms need to be transferred from the metal foils onto target substrates through the conventional wet chemical etching method, which inevitably results in contaminant adsorption on graphene, degradation of graphene intrinsic properties, as well as consumption of metal foils.

An interesting question is whether we can combine the advantages of CVD graphene and chemically exfoliated graphene together, and develop a practical mass production route to high-quality graphene powders with low cost. For this purpose, we paid our attention to the naturally abundant biotemplates for CVD growth of graphene powders. The possible candidate along this consideration is industrially widely used diatomite22,23. Diatomite is a naturally existing material with great abundance on earth (about two million tons per year all over the world), originating from the ancient diatoms as the deposit of diatom frustules24. The chemical composition of diatomite is dominantly SiO2 (8094%) with chemically removable trace amounts of metal oxides and organics. Diatomite has extremely high porosity with light weight, arising from the hierarchical porous structures of individual diatom frustules, which has been widely used as adsorbent, thermal insulating material, lter, catalyst support, decolouring agent, lling material and so on2426.

In this work, we demonstrate the outstanding performance of diatomite as the template for growing hierarchically structured graphene powders by a surface-oxygen-assisted, small-methane-ow CVD route following a self-limited growth mechanism. Graphene growth on planar SiO2 substrates has been well known with good crystalline quality and much less noncarbon elements as compared with the chemically exfoliated graphene powders27,28. Hence, the presented approach based on naturally abundant diatomite is believed to be feasible in principle, giving a route for synthesizing graphene powders with high crystallinity and low cost. Notably, the synthesized graphene products are expected to be signicantly different from the porous-silica-templated CVD graphitic carbon powders reported in the past decade2932. In those CVD processes, the non-selective deposition and non-inductive nucleation of carbon species both on the surface and inside pores of silica templates (for example, zeolites and silica opals) usually lead to formation of the massive

graphitic and amorphous coke particles. Morphologically inverse graphitic frameworks with respect to porous templates were retained after the removal of templates. In contrast, our CVD-grown graphene powders are expected to inherit the hierarchical structures of individual diatom frustules, creating a type of three-dimensional (3D) hierarchical biomorphic graphene (HBG). After the removal of silica templates, the non-planar porous structures of graphene akes could be retained to be free from strong van der Waals and pp stacking, and accessible to the solvent molecules, enabling a rapid and stable high-concentration dispersion of these graphene akes in low boiling point, environment-friendly solvents (for example, ethanol). It may offer a practical solution to the serious aggregation problem encountered in chemically exfoliated graphene powders. Taking into account of the hundreds of versatile biological structures from different diatom sources, such kinds of hierarchical biomorphic graphene are designable in ne microstructures, depending on the purpose of practical applications. Besides, the graphene coating also provides a route for decorating the diatomite material with fascinating functions, which may further expand the wide industrial applications of diatomite itself.

ResultsCVD growth of graphene powders on diatomites. Diatomite has versatile microstructures depending on the diatom source, or say, producing area. Here we use Coscinodiscus wailesii diatom source for demonstration. An individual Coscinodiscus wailesii diatom frustule is composed of two almost equal valves (named as epitheca and hypotheca, respectively) tting together with a girdle (a circular band of silica), and looks like a Petri dish24 (Fig. 1a,b). These valves, comprised of a porous layer of silica, can be separated with girdles by cycled settling from the frustule assemblies (Supplementary Fig. 1). The obtained porous biosilica powders were employed as the CVD growth templates of graphene (Supplementary Fig. 2). The ne hierarchical structures of such kinds of biosilica templates are expected to be preserved during the high-temperature CVD process, and further inherited by the derived graphene (Fig. 1a).

CVD growth of graphene on such biosilica templates changed the original white powders to light grey in macroscopic quantity (Fig. 1c). Removing the biosilica templates by wet-etching, we obtained the black graphene powders (Fig. 1d), accompanied with a marked weight loss. The morphologies of original diatom frustules were found to be well preserved after 1,000 C growth process in the resulting individual graphene akes (Fig. 1e,f; Supplementary Fig. 3). Raman spectrum (Fig. 1g) of thus-produced graphene powders exhibits two characteristic peaks of graphene at 1,582 cm 1(G band) and 2,700 cm 1 (2D band), respectively. Remarkably different from the very weak and broad 2D peak of graphite, as well as the hardly observed 2D peak of RGO, the appearance of sharp 2D peak should indicate the formation of thin-layer graphene with less basal plane defects. The presence of weak Raman D band located at 1,350 cm 1 is attributed to the boundary defects of polycrystalline graphene powders with small domain sizes33,34.

In brief, the above experimental observations conrmed the feasibility of diatomite-based approach for growing high-quality graphene powders. Powder X-ray diffraction patterns of these graphene powders also indicate the absence of layered (002) periodic structures of graphite (Supplementary Fig. 4), distinct from those of RGO and graphitic carbon powders29,30,32.

Characterization of 3D biomorphic graphene. Perfect replication of the ne structures from diatom frustules to graphene akes is demonstrated in Fig. 2 by detailed structural comparisons. Half

2 NATURE COMMUNICATIONS | 7:13440 | DOI: 10.1038/ncomms13440 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications

NATURE COMMUNICATIONS | DOI: 10.1038/ncomms13440 ARTICLE

a

c

d

Before

HBG

Epitheca

After

Marginal pores

Hypotheca

Graphene growth on frustules Biomorphic graphene

b

e

f

g

Margin

Intensity (a. u.)

Girdle

Epitheca

1,200 1,800 2,400 3,000

Hypotheca

Raman shift (cm1)

Figure 1 | Diatomite-based CVD growth of graphene powders. (a) Schematic diagram showing graphene growth on a diatom frustule and its hierarchical biomorphic structures. (b) False colour SEM image of a diatom frustule. (c,d) Photographs of diatomite before and after graphene growth, as well as after removal of biosilica templates, respectively. (e,f) False colour SEM images of an isolated diatom frustule after graphene growth and an individual graphene ake, respectively. (g) Raman spectra of diatomite-derived graphene powders together with graphite, GO and RGO powders. Scale bars, 10 mm.

valve of an individual diatom frustule is actually a natural quasi-two-dimensional microplate (B35 mm in diameter and 12 mm in thickness) made of porous silica skeleton (diatom cell wall). It possesses two typical hierarchical pores, that is, central pores radially distributed at the valve centre with a diameter of B800 nm and marginal pores quasi-periodically located at the valve edge with a diameter of B200 nm (Fig. 2a,b). Similar microscopic pore structures can be clearly seen in the graphene akes after high temperature growth and removal of diatom frustules (Fig. 2c,d; Supplementary Fig. 5). In particular, these holes penetrate through the whole walls of graphene microarchitectures (Fig. 2e), forming aligned hierarchical channels within individual graphene akes. Obviously, the diatomite-derived graphene powders are distinctly different from RGO and LPEG that are composed of simple planar graphene akes. Instead, these biomorphic graphene powders are constructed with non-planar microakes having unique 3D hierarchical channel structures, in addition to the considerably higher crystalline quality.

The surface-group-free nature of such HBG powders was further conrmed by spectroscopic analysis. Fourier transform infrared (FTIR) micro-spectrum of HBG akes shows no discernible peaks from 600 to 1,800 cm 1 (Fig. 2f), in contrast to those of RGO and

GO akes containing hydroxyl (COH), epoxide (COC), carbonyl (C O) and carboxyl (COOH) groups35. The absence

of these chemical groups reveals that the basal plane of HBG akes kept intact. Meanwhile, no signal of silicon-oxygen bond (SiO) was detected in HBG as compared with the FTIR data of biosilica/ graphene (before removing the templates), strongly suggesting the complete removal of diatomite templates. X-ray photoelectron spectroscopy (XPS) analysis also demonstrates that HBG akes are almost free of surface oxygen-containing groups and silicon-containing impurities (Supplementary Fig. 6), consistent with the FTIR and thermogravimetric results (Supplementary Fig. 7). The oxygen percentage in HBG estimated from XPS data is B3 wt%, close to the value in graphite (B2 wt%) but much lower than that of RGO (B15 wt%) (Supplementary Table 1).

In analogy with previously reported growth of graphene via CVD on planar silica-based substrates27,28, lattice oxygen at the surface defect sites of amorphous biosilica can also accelerate the capture and pyrolysis of hydrocarbons at high temperature through the

formation of CO and OH bonds. The nucleation and growth process of graphene can thus be promoted with the formation of minimum-energy sp2-bonded carbon structure36. During the reaction process, the deposition of graphene layers on biosilica surface could be gradually suppressed with increasing layer thickness, due to the attenuated surface activity of substrates coated by continuous graphene layers. This self-limited growth mechanism could be further conrmed by examining the CVD growth of graphene on the surface of individual silica spheres (Supplementary Fig. 8), revealing graphene layer numbers of less than ca. 5 even within sufcient growth durations. Therefore, by selecting suitable methane concentrations, the thickness of graphene layers on the 3D biosilica surface can be on-demand controlled, which is different from those of RGO and LPEG materials.

Figure 3ac exhibit the optical microscope images of the central and marginal regions of a quarter of HBG ake grown at a CH4 concentration of 2.4, 0.9 and 0.6 vol%, respectively, after transferred onto 300 nm SiO2/Si substrates. Generally, the colour contrast reects the thickness of graphene layers, with the darker area assigned to the thicker graphene lms, though it is complicated here by the 3D hierarchical structures. Within a single HBG ake, the edge region always shows a darker contrast, which is attributed to the construction of densely aligned graphene channels replicated from the edge channel structures of original diatom frustules. Similar effects can be clearly observed in the central area when increasing the CH4 concentration. The dark dots shown in Fig. 3a are corresponding to the graphene channels grown on the side walls of original frustule central pores (Supplementary Fig. 9). The colour contrast seen here arises from the complicated 3D stacking of graphene layers and channels after removal of biosilica template.

The actual layer number of graphene can be further estimated from Raman analyses of 2D/G intensity ratio and full width at half maximum of 2D band. For instance, the HBG akes corresponding to Fig. 3ac are mainly composed of few layers, 23 layers, and 12 layers of graphene, respectively (Fig. 3d and Supplementary Fig. 10). At a low CH4 concentration (0.6 vol%), the HBG is mostly monolayer graphene with a 2D/G intensity ratio of ca. 1.8 and a 2D band full width at half maximum of 47 cm 1, well consistent with the single-layer graphene on planar oxide substrates27,33,37. Note that the layer numbers are only estimated

NATURE COMMUNICATIONS | 7:13440 | DOI: 10.1038/ncomms13440 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications 3

ARTICLE NATURE COMMUNICATIONS | DOI: 10.1038/ncomms13440

a b

e

Outside HBG

(i)

(ii) (iii)

GORGO Biosilica/G HBG

Central pores Marginal pores

Inside

c d

HBG HBG

f

1.0

0.8

Absorbance

C=O O-HPhenolic

0.6

C-O

C=C

0.4

0.2

0

800 1,600 2,400 3,200 4,000

Wavenumber (cm1)

Figure 2 | Hierarchical biomorphic structures of diatomite-derived graphene akes. (a,b) False colour SEM images of the central and edge areas of a diatom frustule, respectively. The inset shows the whole valve image. (c,d) False colour SEM images of the derived HBG akes corresponding to a and b after removal of diatom frustule. (e) Morphology of a HBG ake (i), cross-section of its central pores (ii) and details of its marginal pores (iii). (f) FTIR micro-spectra of HBG, Biosilica/G, RGO and GO powders. Scale bars, 2 mm.

for graphene grown on the at area of frustule template for simplicity. It can be seen from the Raman mappings shown in Fig. 3e and Supplementary Figs 11 and 12 that uniform graphene growth has been achieved on the biosilica template under varied CH4 concentrations. Again, the higher Raman intensity contrast in the 2D and G maps at edges indicates densely aligned graphene channels, in accordance with the optical microscopic images. Shown in Fig. 3f is the atomic force microscope image of an individual HBG ake grown at 0.6 vol% CH4 after transferred onto

SiO2/Si substrates. A statistical average height collected on different graphene akes is B1.5 nm (Supplementary Fig. 13), which could correspond to the overlapped single-layer graphene37,38. Moreover, TEM measurements (Fig. 3g and Supplementary Fig. 14) also conrm the thin-layer feature and good crystallinity of HBG akes. Corresponding selected-area electron diffraction pattern (Fig. 3g inset) shows typical six-fold symmetrical spots indexed as the in-plane (hkil) reections of graphene39. In a low-voltage, aberration-corrected, high-resolution TEM image (Fig. 3h), both the edges of one and two graphene layers, and the six-fold symmetrical atomic structures typical for graphene are identied. Meanwhile, the locally convex structures of 3D HBG layers are also claried (Supplementary Fig. 15). Scanning tunnelling microscopy (STM) images shown in Fig. 3i and Supplementary Fig. 16 again demonstrate the atomic resolution honeycomb lattice for the HBG ake transferred onto a 4H-SiC (0001) substrate.

Solution processability of HBG akes. It is known that good dispersion of graphene powders is the premise for various low-cost and high-performance graphene products such as graphene conductive lms, ultralight foams and high-concentration solutions. However, it still remains a challenge to inhibit the restacking of pristine graphene due to its strong interfacial van der Waals interactions and large surface area. As envisioned from the 3D textural features of these atomically thin-layered graphene frameworks, the biomorphic graphene powders show an improved specic surface area compared with the diatomite templates (9.7 m2 g 1) and the RGO powders (420.9 m2 g 1),

which is calculated to be 1,137.2 m2 g 1 by the Brunauer EmmettTeller surface area analysis (Fig. 4a and Supplementary

Table 2). The profound increase (B116 and 2.7 times of that of diatomite and RGO, respectively) is attributed to the lightweight and non-stacking thin-layer nature of HBG powders. In order to probe the dispersion stability of such 3D graphene powders with a large surface area, they were dispersed into various solvents followed by sedimentation, with the dispersion of RGO powders as a reference (at the same concentration of 0.08 mg ml 1;

Supplementary Fig. 17). N-Methyl-2-pyrrolidone (NMP) was found to be best one among the tested solvents for dispersing graphene layers into a stable suspension, due to its perfect match of the polarpolar afnity with graphene (the negative free energy of graphene/NMP mixing system)40,41. The synthesized HBG powders can be directly and fast dispersed in NMP without precipitation, the 3D porous non-stacked structures of which provide the space for the effective penetration of NMP solvent. Distinguished from the complete precipitation of RGO sheets, HBG akes presented relatively good dispersity and stability in NMP after standing for 1 day, which could be attributed to the locally curved structures preserving a weak interlayer interaction. More intriguingly, as shown in Fig. 4b, the transparent HBG dispersion with a concentration of 0.03 mg ml 1 exhibits blue photoluminescence, which could be attributed to the strongly localized p state of the sp2 clusters by the electric states of sp3 defect matrix42. This blue photoluminescence should serve as a direct evidence for the good solubility of HBG akes in NMP, which is similar to that of nanocarbons (for example, carbon dots and carbon nanotubes), but distinguished from that of carbon powders presenting poor solubility in NMP43.

Furthermore, HBG dispersions with varied concentrations from0.03 to 0.11 mg ml 1 were characterized by Zeta-potential analyses, and compared with RGO dispersions (Supplementary

Fig. 18). The decreases of solubility for HBG and RGO in NMP are revealed with the increase of dispersion concentrations, respectively, due to the gradual saturation of graphene dispersions. Nevertheless, it also achieves a comparable production level to the

4 NATURE COMMUNICATIONS | 7:13440 | DOI: 10.1038/ncomms13440 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications

NATURE COMMUNICATIONS | DOI: 10.1038/ncomms13440 ARTICLE

a b c

Margin

2.4 vol% CH4

0.9 vol% CH4

0.6 vol% CH4

d f

e

Raman

10 (a.u.)

Intensity (a. u.)

1.38 nm

Intensity

1,200 1,600 2,000 2,400 2,800

1

Raman shift (cm1)

g

h

i

1L

a1 a

2L

Figure 3 | Thickness-controllable growth of high-quality HBG powders. (ac) Optical microscope images of HBG akes grown at a CH4 concentration of2.4, 0.9 and 0.6 vol%, respectively after transferred onto 300 nm SiO2/Si substrates. (d) Corresponding Raman spectra obtained from a to c. (e) Raman mapping image (2D peak from 2,650 to 2,750 cm 1) of HBG ake shown in a. (f) Atomic force microscope image of the porous graphene ake inheriting from diatom frustule. The height prole taken along the blue line shows a relative height of B1.38 nm to background. (g) TEM image and selected-area electron diffraction pattern (as an inset) of graphene layers grown at 0.6 vol% CH4. (h) Low-voltage, aberration-corrected, high-resolution TEM image of graphene layers, exhibiting the six-fold symmetry and edges of single layer and two layers. (i) STM image (It 1.3 nA, Vs 70 mV) of the graphene

honeycomb lattice. Scale bars, 5 mm (ac), 10 mm (e), 1 mm (f), 500 nm (g), 2 nm (h) and 1.5 nm (i).

shear-exfoliated process of graphite12, which is operated to obtain monolayer and few-layer graphene in NMP with ake sizes of o1 mm (at the concentration up to 0.07 mg ml 1). Besides, a time-consuming chemical/physical exfoliation process (from several hours to several days) is also required to yield monolayer or few-layer graphene sheets for most RGO and LPEG dispersions, in contrast to the fast wet-etching process for HBG powders. Alternatively, high-concentration dispersion (41 mg ml 1) is also achieved for ethyl cellulose(EC)-stabilized HBG akes in ethanol/

terpineol within a short timescale of about several minutes, which also shows an excellent stability (Supplementary Fig. 19). The homogeneous graphene ethanol/terpineol dispersions are prepared with variable concentrations from 0.02 to 4 mg ml 1, as evidenced by their uniform colour contrasts and Tyndall effect (Fig. 4c).

Graphene transparent conductive lms. For transparent electrode applications, the HBG dispersions can be utilized to prepare large-area graphene conductive lms on exible substrates at room temperature. A wire-wound rod-coating technique was applied to these HBG dispersions to prepare a

exible, continuous and thickness-controllable graphene lms on transparent mica substrates (Fig. 4d and Supplementary Figs 20 and 21). An empirical concentration of at least 0.5 mg ml 1 for

HBG dispersions was found to be essential for coating continuous and uniform graphene lms. The optical transmittance of graphene lms decreases with the increase of lm thickness (Fig. 4e). Four-probe resistance measurements were performed to evaluate the conductive properties of graphene/mica lms (Fig. 4f), and the sheet resistances and corresponding transmittances of various graphene lms are plotted in Fig. 4g, respectively. Together with the increase of HBG concentration, the sheet resistance of graphene lm drops quickly from B8.6 to B0.39 kO sq 1 (corresponding conductivity change from B10,400 to B55,000 S m 1)

while the optical transmittance decreases from 91 to 58% at 550 nm. To enhance their conductivity, these graphene lms are further immersed into nitric acid (HNO3). After HNO3 treatment, the average sheet resistance of graphene lms drops to 0.36 kO sq 1 at a transmittance of B80% at 550 nm (see resistance statistics in Supplementary Fig. 22). And the corresponding conductivity is calculated to be B110,700 S m 1,

NATURE COMMUNICATIONS | 7:13440 | DOI: 10.1038/ncomms13440 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications 5

ARTICLE NATURE COMMUNICATIONS | DOI: 10.1038/ncomms13440

a b c d

1,600

V adsorbed (cm3 g1 STP)

(i)

(ii)

1,200

800

(iii) (iv)

400

0

0 0.2 0.4 0.6 0.8 1.0

Relative pressure (P/P0)

e f g

100

Transmittance (%)

0.5 mg mL

104

80

Transmittance (%)

1 )

80

60

R s( sq

103

60

40

102

20

40 400 500 600 700 800

0.5 1.0 1.5 2.0

Wavelength (nm)

Dispersion concentration (mg mL1)

Figure 4 | Solution processability of HBG akes for transparent conducting lms. (a) Nitrogen adsorptiondesorption isotherms of HBG, RGO and diatomite powders. (b) Photographs of HBG NMP dispersions at 0.03 mg ml 1, showing photoluminescence under ultraviolet light. (c) Photographs (iiv)

of EC-stabled HBG in ethanol/terpineol at a concentration of 0.02, 0.05, 0.5 and 4 mg ml 1, respectively. (d) Photograph of a exible transparent HBG/mica lm (4.5 inch) with 80% transparency. (e) Optical transmittances of HBG/mica lms prepared at different graphene concentrations.

(f) Photograph of a patterned graphene Hall bar array fabricated on mica. Inset: optical microscope image of the Hall bar array. (g) Sheet resistance (green and black curves correspond to the nitric acid-treated and -untreated lms, respectively) and transmittance (blue curve without treatment taken at 550 nm) of graphene lms as a function of HBG concentration. The error bars represent the standard deviation of multiple measurement results. Scale bars, 2 cm in (d) and (f), 200 mm in (f) inset.

which is at least one order of magnitude higher than the previously reported hydrazine-reduced RGO (o1,000 S m 1 at 80% transmittance) and LPEG (B6,500 S m 1 at 43% transmittance)

counterparts5,6,40,44,45 (Supplementary Table 3). This marked increase could be attributed to the removal of residual absorbed organics such as EC molecules46, as well as the slight charge doping9, which are efcient for enhancing the conductivity of graphene akes. Further systematic comparisons given in Supplementary Fig. 23 demonstrate the superior electrical conductivities of these graphene lms with regard to various previously reported solution-processed graphene lms in a broad range of optical transmittances. This can be attributed to the better crystallinity and optical semi-transparency of 3D porous graphene building blocks. Besides, HBG powders also exhibit much higher conductivity and better dispersity than those of previously reported graphitic carbon powders (Supplementary Table 4), which offer very high potential for exploiting new graphene-based materials towards energetic and environmental applications.

The electrical resistance over bending was further monitored to evaluate the mechanical durability of HBG/mica lm (Fig. 5a,b). In one bending cycle, the resistance showed a slight increase at a bending radius of 2 mm, which was recovered after release. In contrast, the commercial ITO/poly(ethylene terephthalate) (PET) lm (0.2 mm, B400 O) and the sputtered ITO/mica lm47 exhibited marked resistance increases at a bending radius of 6 mm without recovery after release. Surprisingly, the HBG/mica lm showed no obvious increase (o3%) of electrical resistance over 1,000 bending cycles as seen in Fig. 5c, demonstrating its excellent bending durability as opposed to ITO/PET and sputtered ITO/mica lms. The excellent bending tolerance of HBG/mica lm over fragile ITO arises from the efcient overlapping and electrical contact between large HBG akes, which offers a great freedom for fabricating graphene-based wearable electronic devices. Furthermore, the HBG/mica surface is hydrophobic, having a water contact angle of 81.6 with a B80% transmittance of graphene lm (Fig. 5d). For a thicker

graphene drop-cast lm on mica (B2 mm in thickness), the water contact angle further increased up to 142.3. Therefore, the surface wettability of HBG/mica can be on-demand modulated simply by controlling the HBG lm thickness, providing the possibility for fabricating anti-water mica plates.

Flexible printed graphene electrodes. Inkjet printing is an attractive approach for fabricating patterned graphene electrodes. As demonstrated in Fig. 6a,b, the graphene ink with a volume ratio of 1:4 (Supplementary Fig. 24, viscosity: B12 mPa s; surface tension:

B28 mN m 1, 25 C) could be directly written on paper and SiO2/Si wafer, well comparable with the commercial inks. The optical and

SEM images in Fig. 6c,d of printed stripes on SiO2/Si substrate exhibit stripes of B100 mm width with uniform distribution of graphene akes, where the so-called coffee ring effect is almost not found. The sheet resistance of thus-printed graphene lm reaches a relatively low value of B5 kO sq 1 after 30 printing repetitions with this graphene ink (Fig. 6e), achieving a similar level to that previously reported for the inkjet-printed LPEG48,49. Further decrease of sheet resistance would be possible for less printing passes with further concentrated graphene inks. A roll-to-roll transferred printing technique was also employed to make graphene thick lms hot-pressed on ethylene-vinyl acetate-coated PET substrates for exible electrodes (Fig. 6fh and Supplementary Fig. 25). In this case, the graphene lm shows an electrical conductivity as high as 66,500 S m 1 (Fig. 6i; Supplementary Table 3), which is superior to its RGO and LPEG counterparts6,7,12,50. In particular, thus-obtained graphene lm on PET worked well as the counter electrode of the dye-sensitized solar cells (DSSCs). A power conversion efciency of B5.23% (Fig. 6j) was achieved, competitive with efciency levels of

Pt/FTO-based DSSCs.

DiscussionIn summary, we have developed a scalable and surface-oxygen-assisted CVD route for producing a type of 3D biomorphic graphene powder materials. This approach utilizes the naturally

6 NATURE COMMUNICATIONS | 7:13440 | DOI: 10.1038/ncomms13440 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications

NATURE COMMUNICATIONS | DOI: 10.1038/ncomms13440 ARTICLE

a b

1 )

Normalized resistance (R R 0

16

ITO/PET bending

Normalized resistance (R R 0

12

8

4

0

10 100

Bending radius (mm)

0.1 0 200 400 600 800 1,000

c d

Pristine mica

~ 80%T G/mica film

Opaque G/mica film

0.3

1 )

ITO/PET

0.2

0.1

0.0

Bending cycles

Figure 5 | Mechanical and hydrophobic properties of graphene/mica lms. (a) Normalized resistance of HBG/mica (B50 mm thickness) compared with commercial ITO/PET and sputtered ITO/mica for different bending radii. (b) Bending process. Scale bar, 5 cm. (c) Resistance change of HBG/mica (B50 mm thickness) over bending cycles. The data of sputtered ITO/mica in a and c were collected and calculated from ref. 47. (d) Water contact angles of pristine mica (0), HBG (80% transparency)/mica (81.6) and HBG/mica thick lm (142.3), respectively.

a b c

A4 size (W)

4 inch

d

Graphene ink

e f g h

1010

109

106

+

105

1 )

S(k sq

104

i

100

j

14

12

R 105

10

1 )

102

R S( sq

10

Current density

(mA cm2 )

8

6

10

4

HBG CE ([afii9834] = 5.23%) Pt/FTO CE ([afii9834] = 5.56%)

2

1

0

1 0 20 40 60 80 100Number of printed repetitions 0 0.2 0.4 0.6 0.8

1 10

Thickness (m)

Voltage (V)

Figure 6 | Flexible printed graphene electrodes. (a,b) Photograph of inkjet-printed graphene on A4-sized paper (a) and 4-inch SiO2/Si wafer(b), respectively. (c,d) Optical microscope (c) and false colour SEM (d) images of printed graphene strips on SiO2/Si substrates after 10 printing repetitions. (e) Sheet resistance of printed graphene strips as a function of printing repetitions. (f) Photograph of a vacuum-ltered graphene lm hot-pressed by roll-to-roll printing technique on a PETsubstrate. (g) A green LED lighted through a graphene/PET lm at a starting voltage of 2 V. (h) False colour SEM image of the graphene/PET lm. (i) Sheet resistance versus thickness for the graphene lm on PET substrate. (j) JV characteristics for the dye-sensitized solar cells with a Pt/FTO counter electrode and a graphene counter electrode, respectively. The error bars represent the standard deviation of multiple measurement results. Scale bars, 200 mm (c), 5 mm (d), 1 cm (f) and 10 mm (h).

NATURE COMMUNICATIONS | 7:13440 | DOI: 10.1038/ncomms13440 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications 7

ARTICLE NATURE COMMUNICATIONS | DOI: 10.1038/ncomms13440

abundant and industrially widely used diatomite as the growth template, with the surface growth mediated by a self-limited mechanism. Different from the chemically exfoliated graphene powders, the derived HBG materials are highly crystallized with layer-thickness controllability and less noncarbon impurities. In particular, the individual graphene akes preserve the 3D hierarchical structures of original diatom frustules, effectively overcoming the interlayer stacking and hence giving a wonderful solution dispersion performance essential for various solution-based processes. The graphene lms made from these biomorphic graphene akes exhibit much higher conductivity and excellent bending tolerance than the reported RGO and LPEG counterparts, which is expected to nd wide applications in exible transparent electrodes, polymer composites, conducting inks and printed electronics. The DSSCs using such exible electrodes also have demonstrated a comparable level of power conversion efciency with the expensive platinum-based counterparts.

On the laboratory scale, these puried HBG powders have an estimated yield of ca. 1% (the g/g weight ratio of graphene/ diatomite), presenting a comparable production rate to those of RGO and LPEG powders (Supplementary Table 5). In view of the abundance and low cost of diatom frustules, the bio-inspired CVD process is amenable to scale-up to an industrial level. More importantly, as a special form of graphene materials, 3D biomorphic graphene microarchitectures could pave the way for developing novel topologically structured carbon materials for energetic and environmental applications. Not limited to graphene powders, the presented CVD route could also be extended to the 3D scalable growth of other atomically thin-layered materials such as two-dimensional MoS2 and h-BN, with the merits of mass production, high crystalline quality and low cost.

Methods

Purication of diatomite. The diatom frustules were puried from raw diatomite to obtain the ultrapure biosilica microakes following several steps. First, the as-received diatomite powders (Aldrich) were immersed and stirred overnight in nitric acid (2 mol l 1) and sulphuric acid (1 mol l 1) to remove the organic and metal impurities, respectively. After the recycled ltration and the deionized water cleaning, the biosilica microakes with different particle sizes were separated from the ltrated diatomite using recycled sedimentation processes in acetone.

Growth of hierarchical biomorphic graphene on diatomite. Diatomite powders were put into a three-zone tube furnace. The tube was pumped to vacuum and rinsed with 300 standard-state cubic centimetre per minute (sccm) of 10 vol% hydrogen-mixed argon gas to remove air before it was heated to 1,000 C within 40 min at ambient pressure. The samples were then held at this temperature for 100 min under a constant mixed gas ow of H2/Ar carrier gas (300 sccm) and methane (2 sccm) for graphene growth. The thickness of graphene layers could be controlled by varying the concentration of methane gas. After the furnace was cooled to room temperature, light grey powder was obtained. The powder was then immersed in a hydrogen uoride (HF) etching solution (molar ratio of HF: H2O:

EtOH is 6.7: 27.8: 5.1) at room temperature (or a 6 mol l 1 NaOH solution at 80 C) overnight to remove the biosilica templates. After complete rinsing with water and ethanol, the graphene powder was obtained by freeze-drying at 90 C

and reduced pressure (B1 Pa) for 24 h. For comparison, RGO was reduced from GO with hydrazine hydrate by modied Hummers method51.

Preparation of exible graphene lms. An EC-stabilized graphene dispersion was obtained by adding the as-grown graphene powder into ethanol/terpineol solution containing EC (48% ethoxyl, Aldrich) according to Hersams method52. A0.001 g ml 1 solution of EC in ethanol was rst mixed with the graphene powders. After separated by ltration, the graphene/EC sediment was redispersed in ethanol/

terpineol solution with volume ratio of 9: 1 by shaking up to form a stable graphene suspension with different concentrations. One millilitre of the graphene dispersions was dropped on the edge of a mica substrate (50 mm in thickness). A Meyer rod (18#, RD Specialties, USA) was pulled over the solution to leave a uniform wet lm. During the natural drying process, the graphene lms were pressed under a 1 kg weight overnight to improve their formability. After drying, the graphene lms were heated in Ar/H2 atmosphere at 350 C for 60 min, and then rinsed with acetone and dried by blowing with nitrogen. The thickness of graphene lms after drying (Hdry)

can be controlled by adjusting the concentration of HBG dispersion, according to the

following equation53, Hdry Hwet Co r 1, where the thickness of graphene wet lms

(Hwet) can be regarded as 10% of the wire diameter of the used wire-wound rod, Co is the concentration of the graphene dispersion, and r is approximated as 1.8 g cm 3 referring to the density of graphene oxide lms44, since HBG layers could not be as closely packed as graphite. For the HBG concentrations of 0.5, 0.6, 1.1, 1.6 and2.1 mg ml 1, the thicknesses of dried graphene lms can be calculated to be about11.1, 13.3, 25.1, 35.6 and 46.8 nm, respectively.

Prior to inkjet printing, the solution of graphene/EC in ethanol/terpineol was

bath ultrasonicated for 60 min to yield small graphene fragments, and then ltered through a polycarbonate membrane with 1 mm pores (25 mm in diameter,

Millipore). The ltered solution was concentrated into graphene/EC terpineol dispersion by heating at 120 C to remove ethanol, yielding a graphene ink at a concentration of B0.2 w/v%. The essential requirement of graphene ink compatible with inkjet printing is its viscosity and surface tension. For successful inkjet printing, the graphene terpineol dispersion was diluted with ethanol at different volume ratios ranged from 1:8 to 1:2 to tailor the viscosity and surface tension. An Epson R330 inkjet printer with a T0851 cartridge was used together with graphene ink for printing pictures on A4 paper and narrow lines on SiO2/Si wafers at a substrate temperature of 100 C.

The graphene lms could be also prepared by vacuum ltration, followed by a roll-to-roll transferred printing process on PET substrate. A volume of 200 ml of graphene ethanol dispersion with a concentration of 40 mg ml 1 was vacuum-ltrated using a polycarbonate membrane with 0.45 mm pores (47 mm in diameter, Millipore). The naturally dried graphene lm was then pressed on the ethylenevinyl acetate-coated PET substrate with the graphene side in contact with the substrate at ca. 120 C.

Characterization. Optical microscope (Olympus DX51 microscope), atomic force microscope (Vecco Nanoscope IIIa), SEM (Hitachi S-4800; acceleration voltage 5 30 kV), TEM (FEI Tecnai F20; acceleration voltage 200 kV), aberration-corrected atomic-resolution TEM (FEI Titan 30080; 80 kV), Raman spectroscopy (Jobin Yvon LabRAM HR 800UV; 514.5 nm, 25 mW), ultrahigh vacuum-variable temperature-STM (Omicron, constant current mode), FTIR (Thermo Scientic, Nicolet iN10 MX, transmission mode), XPS (Kratos Analytical Axis-Ultra spectrometer; Al Ka X-Ray source), thermogravimetric (SDT Q600), XRD (Phillips X XPert Pro MPD; Cu Ka1

l 1.540598 , 40 kV, 100 mA), ultraviolet-vis spectroscopy (Perkin Elmer Lambda

950) and static contact-angle measurements (OCA-20 contact angle system) were conducted to characterize the materials, respectively. For SEM and TEM characterization, a PMMA-assisted transfer process was taken for samples onto a SiO2/Si substrate (300 nm oxide layer) and a lacey carbon lm supported on coppergrids, respectively. For STM characterization, the 4H-SiC(0001) substrates were pre-annealed at ca. 900 C in vacuum to improve conductivity.

Device fabrication and measurements. The use of dielectric mica substrates facilitated the transfer-free batch fabrication of graphene transparent electrodes, which is also compatible with high frequency mica capacitors. Standard photo-lithography was used to dene the selected region and fabricate arrays of Hall bar devices. Plasma etching (50 W, 60 s) was used to remove the unwanted regions. Thermal evaporation (UNIVEX 300, Leybold Vacuum) was performed to deposit the metal electrodes with chromium/gold (5 nm/100 nm) as the contacts, which were found to form ohmic contact through annealing at 350 C in Ar/H2 atmosphere.

Four-probe electrical measurements were carried out in a Micromanipulator 6200 probe station with a Keithley 4200 semiconductor characterization system.

A sandwich-type solar cell was assembled by placing a PET-supported graphene lm (counter electrode) on a N719 dye (Solaronix)-sensitized TiO2 photoelectrode on FTO glass (working electrode, effective area of 0.3 0.3 cm2), and clipped

together as an open cell for measurements. The cell was then lled with a liquid electrolyte composed of 0.1 M anhydrous LiClO4, 0.12 M I2, 1.0 M DMPII and0.5 M tert-butylpyridine in dehydrated acetonitrile by capillary force. For comparison, a standard platinum-based counter electrode was also used. The photocurrentvoltage (JV) measurements were taken using a digital source meter (Keithley 2,400) and a solar simulator (Newport, Oriel class A, SP91160A, USA) under AM 1.5 G spectra with a light power density of 100 mW cm 2.

Data availability. The data that support the ndings of this study are available from the corresponding author upon request.

References

1. Geim, A. K. Graphene: status and prospects. Science 324, 15301534 (2009).2. Novoselov, K. S. et al. A roadmap for graphene. Nature 490, 192200 (2012).3. Neto, A. C., Guinea, F., Peres, N., Novoselov, K. S. & Geim, A. K. The electronic properties of graphene. Rev. Mod. Phys. 81, 109 (2009).

4. Geim, A. & Grigorieva, I. Van der Waals heterostructures. Nature 499, 419425 (2013).

5. Eda, G., Fanchini, G. & Chhowalla, M. Large-area ultrathin lms of reduced graphene oxide as a transparent and exible electronic material. Nat. Nanotechnol. 3, 270274 (2008).

8 NATURE COMMUNICATIONS | 7:13440 | DOI: 10.1038/ncomms13440 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications

NATURE COMMUNICATIONS | DOI: 10.1038/ncomms13440 ARTICLE

6. Moon, I. K., Lee, J., Ruoff, R. S. & Lee, H. Reduced graphene oxide by chemical graphitization. Nat. Commun. 1, 73 (2010).

7. Zhu, Y. et al. Graphene and graphene oxide: synthesis, properties, and applications. Adv. Mater. 22, 39063924 (2010).

8. Hao, Y. et al. The role of surface oxygen in the growth of large single-crystal graphene on copper. Science 342, 720723 (2013).

9. Bae, S. et al. Roll-to-roll production of 30-inch graphene lms for transparent electrodes. Nat. Nanotechnol. 5, 574578 (2010).

10. Yan, K., Fu, L., Peng, H. & Liu, Z. Designed CVD growth of graphene via process engineering. Acc. Chem. Res. 46, 22632274 (2013).

11. Dreyer, D. R., Park, S., Bielawski, C. W. & Ruoff, R. S. The chemistry of graphene oxide. Chem. Soc. Rev. 39, 228240 (2010).

12. Paton, K. R. et al. Scalable production of large quantities of defect-free few-layer graphene by shear exfoliation in liquids. Nat. Mater. 13, 624630 (2014).

13. Jeong, S. Y. et al. High-performance transparent conductive lms using rheologically derived reduced graphene oxide. ACS Nano 5, 870878 (2011).

14. Zhang, L. et al. Janus graphene from asymmetric two-dimensional chemistry. Nat. Commun. 4, 1443 (2013).

15. Weiss, N. O. et al. Graphene: an emerging electronic material. Adv. Mater. 24, 57765776 (2012).

16. Mak, K. F., Shan, J. & Heinz, T. F. Electronic structure of few-layer graphene: experimental demonstration of strong dependence on stacking sequence. Phys. Rev. Lett. 104, 176404 (2010).

17. Lee, J. H. et al. Wafer-scale growth of single-crystal monolayer graphene on reusable hydrogen-terminated germanium. Science 344, 286289 (2014).

18. Chen, Z. et al. Three-dimensional exible and conductive interconnected graphene networks grown by chemical vapour deposition. Nat. Mater. 10, 424428 (2011).

19. Gao, T. et al. Temperature-triggered chemical switching growth of in-plane and vertically stacked graphene-boron nitride heterostructures. Nat. Commun. 6, 6835 (2015).

20. Bonaccorso, F., Sun, Z., Hasan, T. & Ferrari, A. C. Graphene photonics and optoelectronics. Nat. Photon. 4, 611622 (2010).

21. Zhang, Y., Zhang, L. & Zhou, C. Review of chemical vapor deposition of graphene and related applications. Acc. Chem. Res. 46, 23292339 (2013).

22. Nassif, N. & Livage, J. From diatoms to silica-based biohybrids. Chem. Soc. Rev. 40, 849859 (2011).

23. Bao, Z. et al. Chemical reduction of three-dimensional silica micro-assemblies into microporous silicon replicas. Nature 446, 172175 (2007).

24. Jeffryes, C., Campbell, J., Li, H., Jiao, J. & Rorrer, G. The potential of diatom nanobiotechnology for applications in solar cells, batteries, and electroluminescent devices. Energ. Environ. Sci. 4, 39303941 (2011).

25. Chu, H., Cao, D., Dong, B. & Qiang, Z. Bio-diatomite dynamic membrane reactor for micro-polluted surface water treatment. Water Res. 44, 15731579 (2010).

26. Chen, P. Y., McKittrick, J. & Meyers, M. A. Biological materials: functional adaptations and bioinspired designs. Prog. Mater. Sci. 57, 14921704 (2012).

27. Sun, J. et al. Direct chemical vapor deposition-derived graphene glasses targeting wide ranged applications. Nano Lett. 15, 58465854 (2015).

28. Chen, Y. et al. Growing uniform graphene disks and lms on molten glass for heating devices and cell culture. Adv. Mater. 27, 78397846 (2015).

29. Xia, Y. & Mokaya, R. Synthesis of ordered mesoporous carbon and nitrogen-doped carbon materials with graphitic pore wall via a simple chemical vapor deposition method. Adv. Mater. 16, 15531558 (2004).

30. Xia, Y. & Mokaya, R. Generalized and facile synthesis approach to N-doped highly graphitic mesoporous carbon materials. Chem. Mater. 17, 15531560 (2005).

31. Wang, X., Bozhilov, K. N. & Feng, P. Facile preparation of hierarchically porous carbon monoliths with well-ordered mesostructures. Chem. Mater. 18, 63736381 (2006).

32. Lee, K. T., Ji, X., Rault, M. & Nazar, L. F. Simple synthesis of graphitic ordered mesoporous carbon materials by a solid-state method using metal phthalocyanines. Angew. Chem. Int. Ed. 121, 57715775 (2009).

33. Chen, J. et al. Near-equilibrium chemical vapor deposition of high-quality single-crystal graphene directly on various dielectric substrates. Adv. Mater. 26, 13481353 (2014).

34. Sun, J. et al. Direct growth of high-quality graphene on high-k dielectric SrTiO3 substrates. J. Am. Chem. Soc. 136, 65746577 (2014).

35. Gao, W., Alemany, L. B., Ci, L. & Ajayan, P. M. New insights into the structure and reduction of graphite oxide. Nat. Chem. 1, 403408 (2009).

36. Liu, B. et al. Importance of oxygen in the metal-free catalytic growth of single-walled carbon nanotubes from siox by a vapor-solid-solid mechanism.J. Am. Chem. Soc. 133, 197199 (2011).37. Chen, J. et al. Oxygen-aided synthesis of polycrystalline graphene on silicon dioxide substrates. J. Am. Chem. Soc. 133, 1754817551 (2011).

38. Reina, A. et al. Layer area, few-layer graphene lms on arbitrary substrates by chemical vapor deposition. Nano Lett. 9, 30873087 (2009).

39. Meyer, J. C. et al. The structure of suspended graphene sheets. Nature 446, 6063 (2007).

40. Hernandez et al. High-yield production of graphene by liquid-phase exfoliation of graphite. Nat. Nanotechnol. 3, 563568 (2008).

41. Bergin, S. D. et al. Towards solutions of single-walled carbon nanotubes in common solvents. Adv. Mater. 20, 18761881 (2008).

42. Eda, G. et al. Blue photoluminescence from chemically derived graphene oxide. Adv. Mater. 22, 505509 (2010).

43. Bae, S. Y. et al. Large-area graphene lms by simple solution casting of edge-selectively functionalized graphite. ACS Nano 5, 49744980 (2011).

44. Dikin, D. A. et al. Preparation and characterization of graphene oxide paper. Nature 448, 457460 (2007).

45. Si, Y. & Samulski, E. T. Synthesis of water soluble graphene. Nano Lett. 8, 16791682 (2008).

46. Geng, H. Z. et al. Effect of acid treatment on carbon nanotube-based exible transparent conducting lms. J. Am. Chem. Soc. 129, 77587759 (2007).

47. Peng, H. et al. Topological insulator nanostructures for near-infrared transparent exible electrodes. Nat. Chem. 4, 281286 (2012).

48. Torrisi, F. et al. Inkjet-printed graphene electronics. ACS Nano 6, 29923006 (2012).

49. He, Q., Wu, S., Yin, Z. & Zhang, H. Graphene-based electronic sensors. Chem. Sci. 3, 17641772 (2012).

50. Li, D., Mller, M. B., Gilje, S., Kaner, R. B. & Wallace, G. G. Processable aqueous dispersions of graphene nanosheets. Nat. Nanotechnol. 3, 101105 (2008).

51. Stankovich, S. et al. Synthesis of graphene-based nanosheets via chemical reduction of exfoliated graphite oxide. Carbon 45, 15581565 (2007).

52. Liang, Y. T. & Hersam, M. C. Highly concentrated graphene solutions via polymer enhanced solvent exfoliation and iterative solvent exchange. J. Am. Chem. Soc. 132, 1766117663 (2010).

53. Wang, J. et al. Rod-coating: towards large-area fabrication of uniform reduced graphene oxide lms for exible touch screens. Adv. Mater. 24, 28742878 (2012).

Acknowledgements

Thanks to M.X. Liu and Y.B. Chen from Peking University for their help and discussion on STM and device measurements. Thanks go to Z. J. Zhou from Henan University for technical support with solar cell devices. This work was nancially supported by the National Basic Research Program of China (nos 2013CB932603, 2016YFA0200103, 2012CB933404, 2012CB921404 and 2013CB934600), the National Natural Science Foundation of China (nos 51520105003 and 51432002), the Specialized ResearchFund for the Doctoral Program of Higher Education of China (no. 20120001130010) and the Beijing Municipal Science and Technology Planning Project (no. Z151100003315013).

Author contributions

Z.F.L. conceived the project. Z.F.L. and K.C. designed the experiments. K.C., C.L., L.R.S., T.G., X.J.S., A.B., Z.Y.Z., Q.Q.J., D.L.M. and M.H.R. carried out the experiments and characterization. D.B., H.L.P. and Z.L.D. performed the devices and measurements. K.C. wrote the manuscript. Z.F.L. and Y.F.Z. revised the manuscript. All of the authors contributed to the data analysis and scientic discussion.

Additional information

Supplementary Information accompanies this paper at http://www.nature.com/naturecommunications

Web End =http://www.nature.com/ http://www.nature.com/naturecommunications

Web End =naturecommunications

Competing nancial interests: The authors declare no competing nancial interests.

Reprints and permission information is available online at http://npg.nature.com/reprintsandpermissions/

Web End =http://npg.nature.com/ http://npg.nature.com/reprintsandpermissions/

Web End =reprintsandpermissions/

How to cite this article: Chen, K. et al. Growing three-dimensional biomorphic graphene powders using naturally abundant diatomite templates towards high solution processability. Nat. Commun. 7, 13440 doi: 10.1038/ncomms13440 (2016).

Publishers note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional afliations.

This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the articles Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/

Web End =http://creativecommons.org/licenses/by/4.0/

r The Author(s) 2016

NATURE COMMUNICATIONS | 7:13440 | DOI: 10.1038/ncomms13440 | http://www.nature.com/naturecommunications

Web End =www.nature.com/naturecommunications 9