Broadband Vertically/Horizontally Dual-Polarized Antenna for Base Stations

Abstract

A broadband vertically/horizontally (V/H) dual-polarized antenna is proposed for mobile communication base stations. The antenna consists of two perpendicularly placed broadband planar antenna elements. By shaping the reflector for V/H dual-polarized antenna, a half-power beam width of 65±8° is achieved for both vertical and horizontal polarization. The V/H dual-polarized antenna has a bandwidth of 48% (1.7-2.75 GHz) for return loss >15 dB, an isolation of 30 dB, and an antenna gain of 9 dBi. An 8-element V/H dual-polarized antenna array is developed, which achieves a bandwidth of 45% (1.7-2.7 GHz) and an antenna gain of 16 dBi, suitable for GSM/UMTS/LTE base stations.

YueHui Cui 1 and XiaoNa Gao 1 and RongLin Li 1

Academic Editor:Ana Alejos

School of Electronic and Information Engineering, South China University of Technology, Guangzhou 510641, China

Received 7 September 2016; Revised 18 January 2017; Accepted 31 January 2017; 6 March 2017

This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

1. Introduction

Dual-polarized antennas are widely used in mobile communication base stations to improve the system performance by utilizing polarization diversity [1]. Vertically/horizontally (V/H) dual-polarized antennas are suitable for base stations in suburban and rural areas because the vertical polarization is dominant in these environments [2, 3]. And normally a V/H array has a higher isolation than a ±45° array. In recent years, lots of dual-polarized antennas have been developed for base stations [4-20]. Most of dual-polarized antennas consist of a patch [4-13] or two crossed dipoles [14-19]. It is well known that patch antennas and dipole antennas usually have different beam widths in the E-plane and H-plane. For example, the half-power beam widths (HPWBs) for the V/H dual-polarized antenna in [18] are about 60° in the E-plane and 70° in the H-plane. Therefore it is quite difficult to achieve the same beamwidth (e.g., ~65°) in the azimuthal plane for both vertical and horizontal polarization, which is usually required for a base station to provide the same coverage for both types of polarization.

In this paper, we present a broadband V/H dual-polarized antenna based on the broadband planar antenna element developed in [20]. The V/H dual-polarized antenna is composed of two such broadband antenna elements which are placed orthogonally to each other for dual-polarization operation. By shaping the reflector for the V/H dual-polarized antenna, a HPBW of 65±8° is obtained in the horizontal plane for both vertical and horizontal polarization. The V/H dual-polarized antenna is described in Section 2 and an 8-element antenna array is developed in Section 3.

2. V/H Dual-Polarized Antenna

2.1. Antenna Configuration

As illustrated in Figure 1, the V/H dual-polarized antenna consists of two perpendicularly placed broadband antenna elements: one is placed for vertical polarization (VP) and the other is placed for horizontal polarization (HP). The broadband antenna element consists of a pair of folded printed dipoles which are coupled to an L-shaped microstrip line [20]. The folded dipoles and the microstrip line are printed on the same substrate, forming a planar antenna element. The horizontal plane (i.e., the y -z plane) is the H-plane for the VP element and the E-plane for the HP element. For a mobile communication base station, the HPBWs in the horizontal plane for both VP and HP elements need to be similar. When the reflector is flat, however, the HPBW for the VP element is about 90±10° while being 70±10° for the HP element, as demonstrated in Figure 2, which is not acceptable for base station applications.

Figure 1: Configuration of a broadband V/H dual-polarized antenna: (a) top view; (b) side view.

(a) [figure omitted; refer to PDF]

(b) [figure omitted; refer to PDF]

Figure 2: HPBWs and gains of the broadband V/H dual-polarized antenna.

[figure omitted; refer to PDF]

The HPBWs for VP and HP in the horizontal plane can be adjusted by shaping the reflector. Since the VP element has a wider HPBW, it needs a wider reflector. It is found by simulation that the total width of the reflector for the VP element is 190 mm while the total width for the HP element is 160 mm. The shape of the reflector is optimized to obtain a HPBW close to ~65° for a 120° sector of a cellular base station. The geometric parameters optimized for the reflector are listed in Table 1 with the geometric parameters for the broadband antenna element.

Table 1: Geometric parameters optimized for the V/H dual-polarized antenna.

Parameter	Value
W 1	2.1 mm
W 2	1.7 mm
W 3	8.4 mm
W 4	5 mm
W 5	52.1 mm
W 6	120 mm
W 7	120 mm
W 8	20 mm
W 9	30 mm
W 10	20 mm
W 11	60 mm
W 12	35 mm
W 13	120 mm
W 14	5 mm
L 1	50 mm
L 2	11.5 mm
L 3	8.75 mm
L 4	15.7 mm
H	43 mm
t	0.76 mm
α 1	150°
α 2	160°
β 1	150°
β 2	110°

2.2. Results

The simulated (using Ansoft HFSS v14 ) and measured HPBWs for the V/H dual-polarized antenna are plotted in Figure 2 with an antenna prototype. The simulated HPBWs in the horizontal plane are 65±8° for both VP and HP elements while the measured HPBWs are 65±3° for HP and 65±10° for VP over the frequency range 1.7-2.7 GHz which covers GSM1800 (1710-1880 MHz), GSM1900 (1850-1990 MHz), UMTS (1920-2170 MHz), LTE2300 (2305-2400 MHz), and LTE2600 (2500-2690 MHz). The slight discrepancy may be due to measurement errors caused by measurement setup. The radiation patterns simulated and measured for VP and HP at the center frequency 2.2 GHz are plotted in Figure 3, showing a similar coverage for both VP and HP; the 10-dB beam widths in the y-z plane are 120°. (There is no significant difference for the radiation pattern over the frequency range 1.7-2.7 GHz.) The antenna gain is about 9 dBi for both VP and HP (also see Figure 2). Simulated and measured S parameters are compared in Figure 4. It can be seen that |S 11| or |S 22| is less than -15 dB (or RL > 15 dB) over a bandwidth of 48% (1.7-2.75 GHz). The isolation (i.e., -|S 21| in dB) between the ports for VP and HP elements is higher than 30 dB. The measured front-to-back ratios compared with the simulation are displayed in Figure 5. The antenna achieves high front-to-back ratios of about 18 dB for both VP and HP, showing good unidirectional radiation. The antenna efficiency is also depicted in Figure 5, which are higher than 85%.

Figure 3: Radiation patterns of the V/H dual-polarized antenna at 2.2 GHz: (a) VP and (b) HP.

(a) [figure omitted; refer to PDF]

(b) [figure omitted; refer to PDF]

Figure 4: S parameters (|S 11|, |S 22|, and |S 21|) simulated and measured for the V/H dual-polarized antenna.

[figure omitted; refer to PDF]

Figure 5: Front-to-back ratios and antenna efficiency of the broadband V/H dual-polarized antenna.

[figure omitted; refer to PDF]

3. Dual-Polarized Antenna Array

For potential applications in mobile communication base stations, an 8-element V/H dual-polarized antenna array is developed, as illustrated in Figure 6. The antenna array is composed of eight V/H dual-polarized antenna elements with an element spacing of 116 mm (~_{λ2.7 GHz} , where _{λ2.7 GHz} is the wavelength in free space at the frequency 2.7 GHz). The V/H dual-polarized antenna array is fed by two eight-way power dividers. Figure 7 shows the measured S parameters for the V/H dual-polarized antenna array. The bandwidth for |S 11| (or |S 22|) <-15 dB is 45% (1.7-2.7 GHz). The isolation between the ports for VP and HP is about 30 dB, ~5 dB higher than that for the ±45° dual-polarized antenna array proposed in [20]. Simulated and measured HPBWs in the horizontal plane (i.e., the y -z plane) and the elevation plane (i.e., the x -z plane) are plotted in Figure 8. Experimental results show that the 8-element V/H dual-polarized antenna array maintains a HPBW of 65±8° in the horizontal plane and a HPBW of 16±2° in the elevation plane for both VP and HP over the frequency range 1.7-2.7 GHz. The slight inconsistency between the measured results and the simulation may have been caused due to measurement errors during the setup of the experiment. The measured gain is about 16 dBi for both VP and HP, as indicated in Figure 9. The measured gains are slightly lower than the simulated results (~17.5 dBi) due to the loss of the feed network (including the power splitter, coaxial cables, and a SMA connector) which was not taken into account in simulation. The gain variation over the frequency range 1.7-2.7 GHz is less than 1.5 dB. The radiation patterns measured at 1.7 GHz, 2.2 GHz, and 2.7 GHz are compared with simulated results in Figure 10; good agreement is observed. A stable similar coverage over the broad frequency range is obtained for both VP and HP. The cross-polarization level is lower than -20 dB. The front-to-back ratios of the antenna array are illustrated in Figure 11, showing the antenna array has a front-to-back ratio higher than 15 dB. The antenna efficiency is also plotted in Figure 11, which is more than 85% over the frequency range covering 1.7-2.7 GHz.

Figure 6: A V/H dual-polarized antenna array: (a) geometry of the antenna array; (b) a prototype of the antenna array.

(a) [figure omitted; refer to PDF]

(b) [figure omitted; refer to PDF]

Figure 7: Measured S parameters of the V/H dual-polarized antenna array.

[figure omitted; refer to PDF]

Figure 8: HPBWs of the V/H dual-polarized antenna array.

[figure omitted; refer to PDF]

Figure 9: Gains of the V/H dual-polarized antenna array.

[figure omitted; refer to PDF]

Figure 10: Radiation patterns of the V/H dual-polarized antenna array: (a) VP at 1.7 GHz; (b) HP at 1.7 GHz; (c) VP at 2.2 GHz; (d) HP at 2.2 GHz; (e) VP at 2.7 GHz; (f) HP at 2.7 GHz.

(a) [figure omitted; refer to PDF]

(b) [figure omitted; refer to PDF]

(c) [figure omitted; refer to PDF]

(d) [figure omitted; refer to PDF]

(e) [figure omitted; refer to PDF]

(f) [figure omitted; refer to PDF]

Figure 11: Front-to-back ratios and antenna efficiency of the V/H dual-polarized antenna array.

[figure omitted; refer to PDF]

4. Conclusion

A broadband V/H dual-polarized antenna is proposed for mobile communication base stations. The dual-polarized antenna achieves a HPBW of 65±8° for both VP and HP elements, a bandwidth of about 48% (1.7-2.75 GHz) for RL > 15 dB, and an isolation of 30 dB. The antenna gain is about 9 dBi for both vertical and horizontal polarization. An eight-element V/H dual-polarized antenna array is also developed. The antenna array has a bandwidth of 45% (1.7-2.7 GHz) and an antenna gain of 16 dBi for both VP and HP, which may find potential applications in GSM/UMTS/LTE base stations.

Acknowledgments

The authors would like to thank the No. 7 Research Institute of China Electronics Technology Group Corporation, Guangzhou, China. The work was supported in part by the National Science Foundation of China (NSFC) under Grant nos. 61501191 and 61372009 and in part by the GDSTC (2014A010103011).

References

[1] B. Lindmark, M. Nilsson, "On the available diversity gain from different dual-polarized antennas,", IEEE Journal on Selected Areas in Communications , vol. 19, no. 2, pp. 287-294, 2001.

[2] J. J. A. Lempiäinen, J. K. Laiho-Steffens, "The performance of polarization diversity schemes at a base station in small/micro cells at 1800 MHz,", IEEE Transactions on Vehicular Technology , vol. 47, no. 3, pp. 1087-1092, 1998.

[3] A. A. Arowojolu, A. M. D. Turkmani, A. A. Arowojolu, A. M. D. Turkmani, P. A. Jefford, C. J. Kellett, "An Experimental evaluation of the performance of two-branch space and polarization diversity schemes at 1800 MHz,", IEEE Transactions on Vehicular Technology , vol. 44, no. 2, pp. 318-326, 1995.

[4] K.-L. Wong, H.-C. Tung, T.-W. Chiou, "Broadband dual-polarized aperture-coupled patch antennas with modified H-shaped coupling slots,", IEEE Transactions on Antennas and Propagation , vol. 50, no. 2, pp. 188-191, 2002.

[5] S. Gao, L. W. Li, M. S. Leong, T. S. Yeo, "A broad-band dual-polarized microstrip patch antenna with aperture coupling,", IEEE Transactions on Antennas and Propagation , vol. 51, no. 4, pp. 898-900, 2003.

[6] K.-L. Wong, T.-W. Chiou, "Finite ground plane effects on broad-band dual polarized patch antenna properties,", IEEE Transactions on Antennas and Propagation , vol. 51, no. 4, pp. 903-904, 2003.

[7] X.-L. Zhao, Q. W. Lin, "Dual-band patch antenna fed by meandering probe for low cross-polarization,", International Journal of Antennas and Propagation , vol. 2016, 2016.

[8] Y. Cheng, Y. Li, W. Lu, "A novel compact dual-polarized antenna,", International Journal of Antennas and Propagation , vol. 2016, pp. =-5, 2016.

[9] H. Wong, K.-L. Lau, K.-M. Luk, "Design of dual-polarized L-probe patch antenna arrays with high isolation,", IEEE Transactions on Antennas and Propagation , vol. 52, no. 1, pp. 45-52, 2004.

[10] Y.-X. Guo, K.-W. Khoo, L. C. Ong, "Wideband dual-polarized patch antenna with broadband baluns,", IEEE Transactions on Antennas and Propagation , vol. 55, no. 1, pp. 78-83, 2007.

[11] H.-W. Lai, K.-M. Luk, "Dual polarized patch antenna fed by meandering probes,", IEEE Transactions on Antennas and Propagation , vol. 55, no. 9, pp. 2625-2627, 2007.

[12] M. Barba, "A high-isolation, wideband and dual-linear polarization patch antenna,", IEEE Transactions on Antennas and Propagation , vol. 56, no. 5, pp. 1472-1476, 2008.

[13] R. Caso, A. Serra, A. Buffi, M. Rodriguez-Pino, P. Nepa, G. Manara, "Dual-polarised slot-coupled patch antenna excited by a square ring slot,", IET Microwaves, Antennas and Propagation , vol. 5, no. 5, pp. 605-610, 2011.

[14] J. Perruisseau-Carrier, T. W. Hee, P. S. Hall, "Dual-polarized broadband dipole,", IEEE Antennas and Wireless Propagation Letters , vol. 2, pp. 310-312, 2003.

[15] G.-X. Zhang, L. Sun, B.-H. Sun, "A wideband dual-polarized antenna using planar quasi-open-sleeve dipoles for base station applications,", International Journal of Antennas and Propagation , vol. 2015, 2015.

[16] Y.-H. Huang, Q. Wu, Q.-Z. Liu, "Broadband dual-polarised antenna with high isolation for wireless communication,", Electronics Letters , vol. 45, no. 14, pp. 714-715, 2009.

[17] Z.-Y. Zhang, S. Li, S.-L. Zuo, J.-Y. Zhao, X.-D. Yang, G. Fu, "Dual-polarized crossed bowtie dipole array for wireless communication applications,", International Journal of Antennas and Propagation , vol. 2014, 2014.

[18] B. Li, Y.-Z. Yin, W. Hu, Y. Ding, Y. Zhao, "Wideband dual-polarized patch antenna with low cross polarization and high isolation,", IEEE Antennas and Wireless Propagation Letters , vol. 11, pp. 427-430, 2012.

[19] B. Q. Wu, K.-M. Luk, "A broadband dual-polarized magneto-electric dipole antenna with simple feeds,", IEEE Antennas and Wireless Propagation Letters , vol. 8, pp. 60-63, 2009.

[20] Y. Cui, R. L. Li, P. Wang, "A novel broadband planar antenna for 2G/3G/LTE base stations,", IEEE Transactions on Antennas and Propagation , vol. 61, no. 5, pp. 2767-2774, 2013.