Synthesis and characterizations of o-nitrochitosan based biopolymer electrolyte for electrochemical devices

Abstract

For the past decade, much attention was focused on polysaccharide natural resources for various purposes. Throughout the works, several efforts were reported to prepare new function of chitosan by chemical modifications for renewable energy, such as fuel cell application. This paper focuses on synthesis of the chitosan derivative, namely, O-nitrochitosan which was synthesized at various compositions of sodium hydroxide and reacted with nitric acid fume. Its potential as biopolymer electrolytes was studied. The substitution of nitro group was analyzed by using Attenuated Total Reflectance Fourier Transform Infra-Red (ATR-FTIR) analysis, Nuclear Magnetic Resonance (NMR) and Elemental Analysis (CHNS). The structure was characterized by X-ray Diffraction (XRD) and its thermal properties were examined by using differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA). Whereas, the ionic conductivity of the samples was analyzed by electrochemical impedance spectroscopy (EIS). From the IR spectrum results, the nitro group peaks of O-nitrochitosan, positioned at 1646 and 1355 cm-1, were clearly seen for all pH media. At pH 6, O-nitrochitosan exhibited the highest degree of substitution at 0.74 when analyzed by CHNS analysis and NMR further proved that C-6 of glucosamine ring was shifted to the higher field. However, the thermal stability and glass transition temperatures were decreased with acidic condition. The highest ionic conductivity of O-nitrochitosan was obtained at ~10−6 cm-1. Overall, the electrochemical property of new O-nitrochitosan showed a good improvement as compared to chitosan and other chitosan derivatives. Hence, O-nitrochitosan is a promising biopolymer electrolyte and has the potential to be applied in electrochemical devices.

About the Authors:

Noriah Abdul Rahman

Roles Data curation, Formal analysis, Investigation, Methodology, Software, Writing – original draft, Writing – review & editing

Affiliation: Faculty of Science and Technology, Universiti Kebangsaan Malaysia, Bangi, Selangor Darul Ehsan, Malaysia

Sharina Abu Hanifah

Roles Conceptualization, Data curation, Formal analysis, Funding acquisition, Project administration, Resources, Supervision, Validation, Writing – review & editing

* E-mail: [email protected] (SAH); [email protected] (LTK)

Affiliations Faculty of Science and Technology, Universiti Kebangsaan Malaysia, Bangi, Selangor Darul Ehsan, Malaysia, Polymer Research Center (PORCE), Faculty of Science and Technology, Universiti Kebangsaan Malaysia, Bangi, Selangor Darul Ehsan, Malaysia

Nadhratun Naiim Mobarak

Roles Data curation, Formal analysis, Investigation, Writing – review & editing

Affiliations Faculty of Science and Technology, Universiti Kebangsaan Malaysia, Bangi, Selangor Darul Ehsan, Malaysia, Polymer Research Center (PORCE), Faculty of Science and Technology, Universiti Kebangsaan Malaysia, Bangi, Selangor Darul Ehsan, Malaysia

Mohd Sukor Su’ait

Roles Data curation, Formal analysis, Investigation, Supervision, Writing – review & editing

Affiliations Polymer Research Center (PORCE), Faculty of Science and Technology, Universiti Kebangsaan Malaysia, Bangi, Selangor Darul Ehsan, Malaysia, Solar Energy Research Institute (SERI), Universiti Kebangsaan Malaysia, Bangi, Selangor Darul Ehsan, Malaysia

Azizan Ahmad

Roles Data curation, Project administration, Supervision, Validation

Affiliations Faculty of Science and Technology, Universiti Kebangsaan Malaysia, Bangi, Selangor Darul Ehsan, Malaysia, Polymer Research Center (PORCE), Faculty of Science and Technology, Universiti Kebangsaan Malaysia, Bangi, Selangor Darul Ehsan, Malaysia

Loh Kee Shyuan

Roles Resources, Validation

Affiliation: Fuel Cell Institute (FCI), Universiti Kebangsaan Malaysia, Bangi, Selangor Darul Ehsan Malaysia

Lee Tian Khoon

Roles Data curation, Formal analysis, Funding acquisition, Validation, Writing – review & editing

* E-mail: [email protected] (SAH); [email protected] (LTK)

Affiliation: Fuel Cell Institute (FCI), Universiti Kebangsaan Malaysia, Bangi, Selangor Darul Ehsan Malaysia

ORCID logo http://orcid.org/0000-0002-9490-4451

Introduction

Chitosan is a linear polysaccharide which has D-glucosamine units and N-acetyl-D-glucosamine units linked by β (1 → 4) [1]. Chitosan can be obtained from the partial deacetylation process of chitin through alkaline treatment by using sodium hydroxide. Chitin can be easily found in marine resources, in the shells of crustaceans, such as crabs, shrimps, the cuticles of insects, and the cell walls of fungi [2–4]. Chitin and chitosan are classified as natural polysaccharide and renewable resources which are currently being intensively explored due to their excellent properties, such as biocompatible, biodegradability, non-toxicity and adsorption properties. Therefore, chitosan is used for many applications, such as pharmaceutical drug delivery system [5], water treatment by removing heavy metal [6,7] and fuel cell [8].

However, chitosan exhibits low conductivity at room temperature between 10−10 and 10−9 S cm-1[9]. In the previous study, the conductivity of chitosan can be improved by adding lithium and ammonium-based salts [10,11], in which complexation takes place through the salt-polymer interaction. Nonetheless, its conductivity is influenced and dependent on the number of free conducting species and degree of dissociation of the salt. Alternatively, the electrochemical properties of the chitosan can be ameliorated through chemical modification. Chitosan can be chemically modified at its free amino group, NH2 at the C-2 position or nonspecific reactions of—OH groups at the C-3 and C-6 positions. These two functional groups also have lone pair of electrons that are suitable for the preparation of solid polymer electrolytes [8]. These functional groups, which are also introduced during chemical modification, will enhance the interaction and complexation with the salt [12]. For the past decades, many chitosan derivatives were synthesized with various methods, such as carboxymethyl chitosan through alkylation [13], phosphorylation [14], quaternary salt formation [15] and sulfonation [16]. Notwithstanding, the exploration and modification of chitosan to its derivatives specifically for polymer electrolyte used in electrochemical devices are still considered new. However, the existence of nitro group in O-nitrochitosan may have high potential to be used as anion exchange membranes. The O-nitrochitosan is expected to have low methanol permeability and better conductivity due to higher water content to be applied in PEMFC.

A few types of chitosan derivatives were explored as solid biopolymer electrolyte (SBE). For example, N-phthaloylchitosan (PhCh) was synthesized by reacting chitosan with phthalic anhydride in dimethylformamide (DMF). Carboxymethyl chitosan was also synthesized, by using monochloroacetic acid and natrium hydroxide. A list of chitosan derivatives and conductivity are tabulated in Table 1, according to the previous studies.

[Figure omitted. See PDF.]

Table 1. Different blank chitosan derivatives with their conductivity values.

https://doi.org/10.1371/journal.pone.0212066.t001

From the best of our knowledge, O-nitrochitosan has not been used for electrochemical device or biopolymer electrolyte. O-nitrochitosan molecule structure has the potential to provide sufficient oxygen to form complexation with cation which will take place when an electric field is applied during conduction. The most similar structure to O-nitrochitosan is carboxymethyl chitosan (CMCS). However, carbon was replaced with nitrogen that is more electronegative. Comparison between four functional groups, NO2- > PO33-> COO- > SO32- were discussed. It was reported that nitro group had the highest electronegativity thus produced the highest conductivity value, 5.22 ×10−6 S cm-1 for the blank system compared to PO3-3, COO- and SO3-2 which their conductivity values were 3.6 ×10−6 S cm-1 [17], 4.0 ×10−7 S cm-1 [13] and 5.0 × 10−9 S cm-1 [18], respectively. In this work, O-nitrochitosan which was synthesized in different ratios of sodium hydroxide was studied. The synthesis route of O-nitrochitosan is illustrated in Fig 1. Further study was done to determine the potential of O-nitrochitosan as biopolymer electrolyte. This biopolymer membrane is expected to have higher conductivity as compared to its predecessor, the chitosan.

[Figure omitted. See PDF.]

Fig 1. The synthesis scheme of O-nitrochitosan.

https://doi.org/10.1371/journal.pone.0212066.g001

Experiment

Materials

Chitosan, medium molecular weight (190,000–310,000) was commercially obtained from Sigma Aldrich. Sodium hydroxide and organic solvent of isopropanol (99.9%), methanol (95%), ethanol (95%) supplied by Systerm were used as solvents. All chemicals were used without further purification. Nitric acid Fume was synthesized in-house by distillation of nitric acid and sulfuric acid at 80 °C for 2 h.

Preparation of O-nitrochitosan powder

The O-nitrochitosan powder was prepared according to the previous work, but with a modification of NaOH volume used [19]. The O-nitrochitosan powder was prepared by adding an amount of chitosan in isopropanol solution and stirred. Thereafter, the solution was introduced with 10%, 20% and 30% of sodium hydroxide, respectively. The pH medium of the chitosan solution was measured by using a pH meter. Then, the solution was stirred for 1 h before the nitric acid fume was added dropwise to the mixture at 55°C for 4 h. Next, O-nitrochitosan was purified via precipitation in methanol and filtered. Afterward, O-nitrochitosan was washed with ethanol for four times. The product was filtered and oven dried at 100 °C. The pH values were only stated as the effect after a certain volume of sodium hydroxide was added before reacting with nitric acid (Table 2).

[Figure omitted. See PDF.]

Table 2. The volume of NaOH added to each sample and the pH value.

https://doi.org/10.1371/journal.pone.0212066.t002

Preparation of film samples

The O-nitrochitosan films were prepared via solution casting technique. An appropriate amount of O-nitrochitosan powder was dissolved in 1% (v/v) aqueous acetic acid solution. The mixture was stirred for 24 h until all O-nitrochitosan powder was completely dissolved and formed a homogenous solution. It was then cast into the petri dish and left to form films, approximately for 72 h in the fume hood. The films were kept in the desiccator for continuous drying.

Characterizations

Attenuated Total Reflection- Fourier transform infrared spectroscopy (ATR-FTIR).

ATR-FTIR analysis was carried out by using Perkin Elmer Spectrum 400 FTIR/FT-NIR spectrophotometer. These spectra were collected in the range of 4,000 cm-1 to 650 cm-1 with a resolution of 2 cm-1. This analysis was conducted to observe changes or shifts in wavelength after comparison between chitosan and chitosan derivative that refers to O-nitrochitosan.

Nuclear Magnetic Resonance (NMR).

The changes in the chemical structures of chitosan and O-nitrochitosan were recorded by using 1H and 13C NMR from Bruker AVANCE III 600 MHz spectrometer. The chitosan and its derivatives were dissolved in the mixture of D2O and CD3COOD.

Elemental analysis (CHNS).

The sample properties were further studied by elemental analysis, CHNS by using TruSpec Micro model. The results can be used to determine the degree of substitution (DS) by using Eq (1) with some modification from [20] Gan et al. 2017.(1)Where, N (%) is the nitrogen content of modified O-nitrochitosan, 169 is the molecular weight of anhydroglucose unit (AGU), 14 is the molecular mass of nitrogen atom and 46 is the net increment in the AGU for every substituted nitro group.

X-ray diffraction (XRD).

The X-ray diffraction was employed to determine the crystallinity of prepared samples. XRD was carried out by using XRD D8 Advance Bruker. The data were collected at room temperature from the range diffraction angle 2θ of 2° to 80° and at the scan rate of 0.05° s-1. Samples in powder and film formed were used in this analysis.

Thermal analysis.

Thermal properties of O-nitrochitosan powder were determined by differential scanning calorimetry (DSC) supplied by Mettler Toledo Model 822c and thermal gravimetric analysis (TGA) was carried out by using Mettler Toledo model TGA/SDTA 851. Glass transition temperature (Tg) from DSC analysis of the chitosan and its derivatives were measured at a heating scan rate of 10 °C/min from 30 °C to 200 °C under nitrogen gas flow. TGA was carried out to investigate the chitosan and O-nitrochitosan decomposition. The samples were heated from 25 °C to 600 °C under argon flow at a heating rate of 10 °C/min.

Electrochemical impedance spectroscopy (EIS).

The value of conductivity of the film samples was characterized by EIS through VersaSTAT (Versastudio software) in the frequency range of 0.1 Hz to10 MHz with 100 mV amplitude. The films were cut into a suitable size and set up in the form of a sandwich between the stainless steel ion-blocking electrodes of conductivity cell with a surface contact area of 1.732 cm2 and connected to a computer [21]. The bulk resistance (Rb) was determined from the equivalent circuit analysis by using the Zview analyzer software. The impedance data were processed by Zview in a complex impedance plot, where the imaginary part, Zi (Z’) was plotted against its real part Zr (Z”). The electrical conductivity (σ) of the films was calculated from Eq (2):(2)Where, t is the film thickness (cm) and A is the film-electrode contact (cm2). The analysis was performed at room temperature [22].

Results and discussion

ATR-FTIR analysis of O-nitrochitosan powder.

The chemical properties of O-nitrochitosan powder were characterized by using ATR-FTIR, 1H NMR and CHNS analyses. Fig 2 depicts the ATR-FTIR spectra for chitosan and its derivatives in powdered form. ATR-FTIR spectrum shows all the main six peaks for chitosan. First, a strong and broad stretching peak band of O-H can be seen overlapping with N-H peak at 3328 cm-1 as reported by Samantha et al. [23]. Second, peak axial stretching of C-H is depicted at 2872 cm-1. Three types of amide groups of chitosan, which were identified at 1644 cm-1, 1569 cm-1 and 1320 cm-1, corresponded to C = O stretching (amide I), N-H bending (amide II), and C-N stretching (amide III), respectively [23,24]. Finally, the peaks in the range of 1151–897 cm-1 shifted to the left (1065–993 cm-1), corresponding to symmetric and asymmetric stretching vibrations of C-O and C-O-C polysaccharide skeleton [25].

[Figure omitted. See PDF.]

Fig 2. ATR-FTIR spectra of chitosan and its derivatives (powdered form) in acidic medium.

The data is available in S1 Fig.

https://doi.org/10.1371/journal.pone.0212066.g002

After modification, a strong and wide band of O-H that overlapped with N-H band (3349 cm-1) in chitosan became sharper and the N-H peak shifted to the left to 3453 cm-1. This proved that the quantity of O-H stretched decreased as nitro group substituted on one of three hydroxyl groups in chitosan. C-H peak also shifted to the left to 3262 cm-1. The introduction of nitro group to the chitosan resulted in two new sharp peaks, which appeared at 1,646 cm-1 and 1,355 cm-1. The sharp peak at 1646 cm-1 was the combination of three peaks, namely C = O stretching, asymmetric NO2 stretching and OH deformation vibrations which associated with amide I group [7]. On the other hand, the peak at 1355 cm-1 was the combination peak of symmetry NO2, C = O stretching, CH3 deformation and C-N stretching vibration. The other OH deformation peak can be seen at 827 cm-1, as being reported by the previous study [7].

1H-NMR analysis for O-nitrochitosan powder.

Fig 3 depicted the 1H NMR spectrum of O-nitrochitosan at various pH media in D2O. The proton assignments of O-nitrochitosan pH 1 were as follows (ppm): 1H NMR (D2O):2.01 (CH3, acetamido group of chitosan), 4.60 (H1), 3.03 (H2), 3.82 (H3), 3.89 (H4), 3.67 (H5), 3.91, 3.77 (H6). The proton assignments of O-nitrochitosan pH 6 were as follows (ppm): 1H NMR (D2O):2.01 (CH3, acetamido group of chitosan), 4.70 (H1), 3.00 (H2), 3.77 (H3), 3.89 (H4), 3.65 (H5), 3.91 (H6). The proton assignments of chitosan were as follows (ppm): 1.96 (CH3, acetamido group of chitosan), 4.70 (H1), 3.06 (H2), 3.75 (H3), 3.80 (H4), 3.63 (H5), 3.80, 3.65 (H6) [19]. The proton at C-6 of glucosamine ring of O-nitrochitosan, at both pH 1 and pH 6, were higher than the proton in chitosan due to the substitution of nitro group at C6 in both materials; thus, the electronegativity of the proton shifted to the higher field.

[Figure omitted. See PDF.]

Fig 3. 1H NMR spectrum of O-nitrochitosan at (a) pH 1 and (b) pH 6 in D2O.

The inset shows the repeating unit of chitosan (m < n).

https://doi.org/10.1371/journal.pone.0212066.g003

Elemental analysis (CHNS) analysis for O-nitrochitosan powder.

Table 3 shows the percentage of carbon, oxygen, nitrogen and degree of substitution (DS) of chitosan as well as O-nitrochitosan. Elemental analysis is used to determine the degree of substitution that will take place after some modification is completed. Through this analysis, we can estimate the number of nitro group that will substitute the two hydroxyl groups in the chitosan structure after modification with nitration process in different percentage of NaOH media. The DS of nitro can be calculated from Eq (1). The DS of O-nitrochitosan were obtained at 1.22, 1.12 and 1.28. After the modification, the nitrogen and oxygen content were increased. This can be seen when the percentage of nitrogen and oxygen in the derivatives chitosan increased compared to the chitosan. Subsequently, the increase of nitro group has enchanced the conductivity of chitosan derivatives, which can be seen in latter part (proton conductivity section). The nitro group which possesses strong electron-withdrawing property will facilitate the coordination with the proton [13]. Thus, the ion mobility will increase.

[Figure omitted. See PDF.]

Table 3. Elemental percentage of chitosan and O-nitrochitosan.

https://doi.org/10.1371/journal.pone.0212066.t003

Mechanism of O-nitrochitosan.

The mechanism of O-nitrochitosan began in the acidic medium with the base abstracting the proton from the alcohol by using a base as soon as sodium hydroxide was added, as shown in Step 1. In the chitosan structure, the reaction only occurred at three places; C2, C3, and C6. This reaction occurred at C6 because it was easier to react since the C6 position was outside of the chitosan ring. Next, alkoxide will attract the Na+ from NaOH (Step 2) to form sodium salt chitosan formation. This formation was temporary. When the sodium left from sodium salt chitosan formation, it will make the alkoxide formation again. Then, the alkoxide will donate its electron to the electrophilic nitronium when the nitric acid fume was added to the reactant and formed O-nitrochitosan, as seen in Step 3. The reaction that took place in the overall reaction was SN2 replacement. Fig 4 shows the proposed reaction mechanism of O-nitrochitosan in the acidic medium.

[Figure omitted. See PDF.]

Fig 4. The proposed mechanism from chitosan to O-nitrochitosan.

https://doi.org/10.1371/journal.pone.0212066.g004

XRD analysis of powder.

XRD diffractogram of chitosan powder and its derivatives are shown in Fig 5. From diffractogram of chitosan powder, the presence of broad peaks, at around 2θ = 9.4 °, 20.0 ° and 28.4°, showed that chitosan exhibited a high degree of crystallinity phase [13,26]. After modification with the addition of nitro group, the intensity at the broad peaks of chitosan derivatives were decreased. However, small and sharp peaks appeared at 8.45 ° and from 20 ° to 50 ° region, which indicated that the crystallinity increased at some parts of chitosan as number of hydrogen bond also increased when it was derived from O-nitrochitosan. These findings were supported by glass transition temperature (Tg) of chitosan which was 73 °C, while the chitosan derivatives at different pH media obtained higher Tg from 78°C to 80 °C.

[Figure omitted. See PDF.]

Fig 5. XRD diffractogram of chitosan powder and its derivatives.

The data is available in S2 Fig.

https://doi.org/10.1371/journal.pone.0212066.g005

Thermal analysis.

TGA and DTG curves of chitosan and its derivatives are shown in Fig 6 and tabulated in Table 4. As we can see from the thermogram, chitosan has two stages of degradation and O-nitrochitosan has three stages of degradation. For chitosan, the first stage began at 80 °C and up to 100°C with a weight loss of about 4% to 8%, which was due to water loss, which is related to the hydrophilic nature of chitosan [27]. For the second stage of degradation, it began at about 280°C, which contributed from depolymerization and decomposition of the basic unit of polymer polysaccharides. For O-nitrochitosan, the first degradation was referred to the water loss. A weight loss of more than 52% started at about 197 °C, which attributed to the degradation of glycerol and depolymerization in chitosan, was the second stage of degradation [27]. Next, the third stage of degradation happened after 280 °C as we can see from TGA and DTG thermogram, as shoulder peak as referred to the weight loss of the nitro functional group. The introduction of nitro group to the structure of chitosan has shifted the second main peak from 280 °C to 197°C and caused the third stage of degradation. Fig 6 shows the TGA and DTG thermograms.

[Figure omitted. See PDF.]

Fig 6. TGA and DTG thermograms of chitosan and its derivatives.

The data is available in S3 Fig.

https://doi.org/10.1371/journal.pone.0212066.g006

[Figure omitted. See PDF.]

Table 4. Temperature of degradations and number of degradation steps of chitosan powder and its derivatives.

https://doi.org/10.1371/journal.pone.0212066.t004

Fig 7 shows the second run of DSC thermogram of O-nitrochitosan pH 1, pH 2 and pH 6 in the temperature range of 0°C –590 °C. From the DSC thermogram, traces of the chitosan were seen at the first endothermic peak, at 80–100°C, which attributed to absorb moisture [27]. Polysaccharide like chitosan has a strong affinity towards water and their endotherm is normally related to the evaporation of water. These molecules are different in water holding capacity; thus, it will affect the strength of water-polymer interaction. The endothermic values were observed to be higher in chitosan derivatives than chitosan itself. This may correspond to the evaporation of water which reflected the physical and molecular changes during chemical modification [28, 29]. The Tg temperature for chitosan derivatives was about 120°C to 123°C. Researchers have found that chitosan has a few values of glass transition [30,31]. Chitosan has a lower glass temperature of 73°C than its derivatives, which were around 78°C-80°C. Table 5 shows the glass transition temperature for chitosan powder and its derivatives.

[Figure omitted. See PDF.]

Fig 7. Second run thermal analysis curves for (a) chitosan, O-nitrochitosan pH 1, pH 2 and pH 6.

The data is available in S4 Fig.

https://doi.org/10.1371/journal.pone.0212066.g007

[Figure omitted. See PDF.]

Table 5. Glass transition temperature for chitosan powder and its derivative.

https://doi.org/10.1371/journal.pone.0212066.t005

Ionic conductivity.

The potential of O-nitrochitosan as solid biopolymer electrolytes was investigated by determining its ionic conductivity. The nitrochitosan films were yellowish in color, semi-transparent and flexible, as shown in Fig 8, whereas the conductivity results of the films are tabulated in Table 6.

[Figure omitted. See PDF.]

Fig 8. Physical observation of (a) chitosan film and (b) nitrochitosan film.

https://doi.org/10.1371/journal.pone.0212066.g008

[Figure omitted. See PDF.]

Table 6. The conductivity of the nitrochitosan film.

https://doi.org/10.1371/journal.pone.0212066.t006

From Table 6, the conductivity of O-nitrochitosan polymer electrolyte membrane had achieved a higher value as compared to chitosan membrane. The conductivity increased about four orders of magnitude from 8.88 × 10−10 S cm−1 to 5.22 × 10−6 S cm−1. This showed that the chemical modification on chitosan by increasing the amount of oxygen in the structure of O-nitrochitosan has affected the conductivity properties of chitosan. The conductivity of blank O-nitrochitosan was expected to increase due to the oxygen atoms which possessed lone pairs of electrons that will coordinate with the cations. The more oxygen introduced to the chitosan structure, will mean that the number of active sites per repeating unit in the polymer also increased. This will enhance the migration of protons through the polymer matrix by providing more vacant sites for proton transport to occur. Since acetic acid was used in this blank system, H+ will dissociate from CH3COOH. Complexes of H+ from acetic acid will form with the oxygen atom from functional groups, O-H and O-NO2. The lone pairs of electron from O-NO2 were donated to H+ during complexation, as illustrated in Fig 9. When the electric field was subjected to the solid polymer electrolyte, the cations will transfer to the coordinating sites. It will transfer from one coordinated site to another in the same polymer chain or its neighbor due to the weak coordination of cations and the site along the polymer chain [32, 33]. The transportation of cations through the sites was also assisted by the segmental motion of polymer chain [13].

[Figure omitted. See PDF.]

Fig 9. H+ conduction mechanism in O-nitrochitosan.

https://doi.org/10.1371/journal.pone.0212066.g009

Fig 10 shows complex impedance plots obtained on (a) chitosan and (b) O-nitrochitosan based green polymer electrolyte film. The plot was composed of two different regions, which were a slanted spike at low frequency and a semicircle at high frequency. The linear region was correlated with the existence of concentration gradients that gave rise to diffusion processes in the bulk electrolyte [34] while the semicircle part was linked to ionic conduction in the sample bulk resistance. The semicircle was embodied by a combination of resistor and capacitor in a parallel arrangement. The resistor can detect the ionic transportation within the polymer matrix while the capacitor measured the capacitance in the alternating field when immobile polymer chains became polarized [34]. In this system, the blocking electrode was used. So, the electrode/electrolyte interface can be reflected as capacitance. A slanted spike appeared instead of a vertical spike since the capacitance was non-ideal. The ideal capacitance will incline spike at 90°. The non-ideal spike will spike at an angle of less than 90°, due to non-homogeneity or roughness of the electrolyte/electrode interface. Besides, the degree of the slope and peak preference can be determined by relaxation time of mount up charge carrier at the interface [35].

[Figure omitted. See PDF.]

Fig 10. The complex impedances plot of (a) chitosan and (b) O-nitrochitosan.

The data is available in S5 Fig.

https://doi.org/10.1371/journal.pone.0212066.g010

XRD analysis of nitrochitosan films.

Fig 11 depicted the XRD patterns of chitosan film and its derivatives. The percentage of amorphous of all O-nitrochitosan films showed some increase when the powder was made into the film form. The crystalline peak of chitosan, which were around 2θ = 9.4°, 20.0° and 28.4°, were decreased because the hydrogen bond in the film was interrupted. The enhancement of the amorphous phase is important to increase the conductivity of the polymer. The polymeric chain will become more flexible in the amorphous phase, and thus increases the polymer segmental motion and will allow easier ion transport in this phase. The 2θ peak which, represent the crystallinity character of chitosan film forms and its derivatives are shows in Table 7.

[Figure omitted. See PDF.]

Fig 11. XRD diffractogram of chitosan film and its derivatives.

The data is available in S6 Fig.

https://doi.org/10.1371/journal.pone.0212066.g011

[Figure omitted. See PDF.]

Table 7. Peaks of 2θ in chitosan film and its derivatives.

https://doi.org/10.1371/journal.pone.0212066.t007

Conclusion

The O-nitrochitosan in the acidic medium was successfully prepared and used as a host polymer for green polymer electrolyte. Chitosan-based electrolytes as a control experiment were also prepared. Both biopolymer electrolytes were prepared by solution casting technique. ATR-FTIR analysis confirmed that the interaction between the polymer host and acetic acid solvent has shifted the wavenumber of hydroxyl and amine band. The conductivity of the new chitosan derivatives showed its potential as green biopolymer electrolyte after their conductivity value showed some increases of about four orders of magnitude from ~10−9 to ~10−6 S cm-1.

Supporting information

[Figure omitted. See PDF.]

S1 Fig. ATR-FTIR spectra of chitosan and its derivatives (powdered form) in acidic medium.

https://doi.org/10.1371/journal.pone.0212066.s001

(JNB)

S2 Fig. XRD diffractogram of chitosan powder and its derivatives.

https://doi.org/10.1371/journal.pone.0212066.s002

(JNB)

S3 Fig. TGA and DTG thermograms of chitosan and its derivatives.

https://doi.org/10.1371/journal.pone.0212066.s003

(JNB)

S4 Fig. Second run thermal analysis curves for (a) chitosan, O-nitrochitosan pH 1, pH 2 and pH 6.

https://doi.org/10.1371/journal.pone.0212066.s004

(JNB)

S5 Fig. The complex impedances plot of (a) chitosan and (b) O-nitrochitosan.

https://doi.org/10.1371/journal.pone.0212066.s005

(JNB)

S6 Fig. XRD diffractogram of chitosan film and its derivatives.

https://doi.org/10.1371/journal.pone.0212066.s006

(JNB)

Acknowledgments

The authors would like to thank Universiti Kebangsaan Malaysia (UKM) for financial support and facilities through the grant code FRGS and Modal Insan UKM. Special thanks also to the Faculty of Science and Technology and Centre for Research and Instrumentation Management (CRIM) at UKM for providing technical and facilities.

Citation: Rahman NA, Abu Hanifah S, Mobarak NN, Su’ait MS, Ahmad A, Shyuan LK, et al. (2019) Synthesis and characterizations of o-nitrochitosan based biopolymer electrolyte for electrochemical devices. PLoS ONE 14(2): e0212066. https://doi.org/10.1371/journal.pone.0212066

References

1. de Alvarenga ES. Biotechnology of Biopolymer. Biotechnology of Biopolymers. Elnashar M., Ed., InTech, Rijeka, Croatia.

2. Jayakumar R, Prabaharan M, Nair SV, Tokura S, Tamura H, Selvamurugan N. Novel carboxymethyl derivatives of chitin and chitosan materials and their biomedical applications. Prog Mater Sci. 2010; 55: 675–709.

3. Chen L, Du Y, Zeng X. Relationships between the molecular structure and moisture-absorption and moisture-retention abilities of carboxymethyl chitosan II. Effect of degree of deacetylation and carboxymethylation. Carbohydr. Res. 2003; 338: 333–340. pmid:12559731

4. Chen L, Du Y, Wu H, Xiao L. Relationship between molecular structure and moisture-retention ability of carboxymethyl chitin and chitosan. Journal of Appl Polym Sci. 2002; 83: 1233–1241.

5. Krishna Rao KSV, Kumar Naidu BV, Subha MCS, Sairam M, Aminabhavi TM. Novel chitosan-based pH-sensitive interprenating network microgels for the controlled release of cefadroxil. Carbohydr Polym. 2006; 66: 333–344.

6. An NT, Thien DT, Dong NT. Dung PL. Water-soluble N-carboxymethylchitosan derivatives: Preparation, characteristics and its application. Carbohydr Polym. 2009; 5: 489–497.

7. Jha PJ, Halada GP, McLennan SM. Electrochemical synthesis of nitro-chitosan and its performance in chromium removal. Coatings. 2013; 3: 140–152.

8. Vaghari H, Malmiri HJ, Berenjian A, Anarjan N. Recent advances in application of chitosan in fuel cells. Sustain Chem Processes. 2013; 1: 1–12.

9. Wan Y, Creber KAM, Peppley B, Bui VT. Ionic conductivity of chitosan membranes. Polymer. 2002; 44: 1057–1065.

10. Jaafar NK, Lepit A, Aini NA, Saat A, Ali AMM, Yahya MZA. Effects of lithium salt on chitosan-g-PMMA based polymer electrolytes. Mater Res Innov. 2011.

11. Mobarak NN, Ramli N, Abdullah MP, Ahmad A. Spectroscopic studies of carboxymethyl chitosanammonium triflate (NH4CF3SO3) based solid Polymer Electrolytes. AIP Conference Proceedings. 2013; 1571, 843;

12. Cardoso J, Nava D, García-Morán P, Hernández F, Gomez B, Vazquez-Arenas J. et al. Synthesis, characterization and theoretical insights of green chitosan derivatives presenting enhanced Li+ ionic conductivity. J Phys Chem Biophys. C, 2015. 10.

13. Mobarak NN, Ahmad A, Abdullah MP, Ramli N, Rahman MYA. Conductivity enhancement via chemical modification of chitosan based green polymer electrolyte. Electrochim Acta. 2013; 92: 161–167.

14. Jayakumar R, Nagahama H, Furuike T, Tamura H. Synthesis of phosphorylated chitosan by novel method and its characterization. Int J Biol Macromol. 2008; 42: 335–339. pmid:18279950

15. de Britto D. Assis OBG. A novel method for obtaining a quaternary salt of chitosan. Polymers. 2007; 69: 305–310.

16. Tsai HS, Wang YZ, Lin JJ, Lien WF. Preparation and properties of sulfopropyl chitosan derivatives with various sulfonation degree. J Appl Polym Sci.

17. Liew JWY, Loh KS, Ahmad A, Lim LL, Daud WRW. Effect of modified natural filler o-methylene phosphonic κ-carrageenan on chitosan-based polymer electrolytes. Energies. 2018;11: 1910.

18. Aziz NA, Majid SR & Arof AK. Synthesis and characterizations of phthaloyl chitosan-based polymer electrolytes. J Non Cryst Solids. 2012; 358: 1581–1590.

19. Rahman NA, Hanifah SA, Zani AMN & Ahmad A. Modification of chitosan for preparation of poly (N-isopropylacrylamide/ O-nitrochitosan) interpenetrating polymer network. Sains Malays. 2015; 44: 7995–1001.

20. Pires NR, Cunha PLR, Maciel JS, Angelim AL, Melo VMM, de Paula RCM & Feitosa JPA. 2013. Sulfated chitosan as tear substitute with no antimicrobial activity. Carbohydr Polym; 91: 92–99 pmid:23044109

21. Majid SR, Arof AK. Proton-conducting polymer electrolyte films based on chitosan acetate complexed with NH4NO3 salt. Physica B Condens Matter 2005; 355: 78–82

22. Yusuf SNF, Azzahari AD, Yahya R, Majid SR, Careem MA. & Arof AK. From crab shell to solar cell: a gel polymer electrolyte based on N -Phthaloylchitosan and its application in dye-sensitized solar cells. J Mater Chem. 2016; 6: 27714.

23. Samantha HS, Ray SK. Controlled release of tinidazole and theophylline from chitosan based composite hydrogels. Carbohydr Polym. 2014; 106: 109–120. pmid:24721057

24. Wang W, Yu W. Preparation and characterization of CS-g-PNIPAAm microgels and application in a water vapour-permeable fabric. Carbohydr Polym. 2015; 127: 11–18. pmid:25965451

25. de Abreu FR & Campana-Filho SP. Characteristics and properties of carboxymethylchitosan. Carbohydr Polym. 2009; 75: 214–221.

26. Ma G, Yang D, Zhou Y, Xiao M, Kennedy JF, Nie J. Preparation and characterization of water-soluble N-alkylated chitosan. Carbohydr Polym. 2008; 74: 121–126.

27. Kurek M, Brachais CH, Nguimjeu CM, Bonnotte A, Voilley A, Galic K, Couvercelle J-P, Debeaufort F. Structure and thermal properties of a chitosan coated polyethylene bilayer film. Polym Degrad Stab. 2012; 97: 1232–1240.

28. Kittur FS, Harish Prashanth KV, Udaya Shankar K, Tharanathan RN. Characterization of chitin, chitosan and their carboxymethyl derivatives by differential scanning calometry. Carbohydr Polym. 2002; 49: 185–193.

29. Ahmad M, Ahmed S, Swami BL, Ikram S. Preparation and characterization of antibacterial thiosemicarbazide chitosan as efficient Cu(II) adsorbent. Carbohydr Polym. 2015; 132: 164–172. pmid:26256337

30. Quijada-Garrido I, Iglesias-Gonzalez V, Mazon-Arechederra JM, Barrales-Rienda JM. The role played by the interactions of small molecules with chitosan and their transition temperatures. Glass-forming liquids: 1,2,3-propantriol (glycerol). Carbohydr Polym. 2007; 68: 173–186.

31. Suyatma NE, Tighzert L, Copinet A. Effects of hydrophilic plasticizers on mechanical, thermal and surface properties of chitosan films. J Agric Food Chem. 2005; 53: 3950–3957. pmid:15884822

32. Aziz NA, Majid SR, Arof AK. Synthesis and characterizations of phthaloyl chitosan-based polymer electrolytes. J Non Cryst Solids. 2012; 358: 1581–1590.

33. Mobarak NN, Ghani MA, Abdullah MP, Ahmad A. Chemical Interaction, Conductivity and Thermal Properties of kappa carrageenan based Polymer Electrolytes. Adv Mat Res. 2015; 1107: 168–174

34. Mobarak NN, Ramli N, Ahmad A, Rahman MYA. Chemical interaction and conductivity of carboxymethyl κ-carrageenan based green polymer electrolyte. Solid State Ion. 2012; 224: 51–57.

35. Liew CW, Ramesh S, Ramesh K, Arof AK. Preparation and characterization of lithium ion conducting ionic liquid-based biodegradable corn starch polymer electrolytes. ECS J Solid State Sci Technol. 2012; 1–7.