This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
1. Introduction
1.1. Research Background
In cases where resonance cannot be avoided in models with low loss factors, viscoelastic materials such as rubber are used to reduce mechanical vibration or noise. Passive patches are used when the structure to be designed has weight or space limitations. They are currently being used in a variety of fields such as the aerospace, marine, construction, and automotive fields [1]. To achieve a light weight, the thickness of the structures is reduced, and the damping effect of passive patches can be clearly observed. The passive patch also has a simple structure and is cost-effective. Additionally, research on beam structure analysis prior to patch application is being actively conducted. Baran et al. [2] investigate the influence of the Adomian decomposition method (ADM) and differential transform method (DTM) on the free vibration of Timoshenko beams and analyse the effects on variables such as axial compressive load and ground reaction force by considering boundary conditions. The results of DTM and ADM show excellent agreement, utilizing the dynamic stiffness method (DSM) to verify the mode shapes and highlighting its applicability to free vibration of beam assembly structures resting on a viscoelastic basis. Additionally, the natural frequencies and harmonic response of the cracked frame were analysed using the transfer matrix method (TMM), single variable shear deformation theory (SVSDT), and Timoshenko beam theory, and it was shown that TMM can be used for simple and efficient analysis [3–5].
The application of passive patches is divided into two categories: constrained attenuation with elastic restraint and viscoelastic layers and nonconstrained attenuation with only viscoelastic layers. In general, the damping effect of the constrained damping technique is large. In this technique, the vibration energy dissipation due to the shear deformation of the viscoelastic layer induces attenuation [6]. The technique provides the greatest attenuation when used over the entire range. However, a passive patch of a reasonable size is more effective in terms of cost and design. Hence, the patch position is mainly determined by considering the mode with a large contribution. However, in order to achieve great efficiency using minimal passive patches, vibration analysis must be done to determine patch locations where vibration attenuation for various modes can be obtained.
Passive patches can achieve attenuation effects over a wide frequency range. Although a good attenuation effect can be obtained in the high-frequency band, the attenuation performance is insufficient in the low-frequency band. Various methods, including the Rayleigh–Ritz method, have been investigated for modeling passive patch viscoelastic materials [7, 8]. In addition, various methods have been studied for modeling viscoelastic materials used in passive patches. These include an approach for modeling passive patches for plates and beams using the Rayleigh–Ritz method to estimate the natural frequencies and loss coefficients quickly [9–13]. Modeling of harmonic excitations is proposed when a passive patch and an active patch are installed [14]. In such a case, it is necessary to optimize the position of a small passive patch before applying the active patch. In the case of passive patches, the result is affected not only by the position of the patch’s bending shape function but also by the loss factor of the viscoelastic layer, the shear coefficient, thickness, length, elastic modulus and thickness of the lower object to be controlled, and the length of the passive patch [13]. Thus, the effects of the previous parameters on the design of passive patches have been studied [13, 15, 16].
To optimize the position of a passive patch, Zheng et al. minimized the length and position of the patch by using a genetic algorithm based on the penalty function method [17, 18]. Lei and Zheng have optimized the passive patch location through topological optimization of the penalization model [19, 20], and Fang has used the level set method [21]. Araujo et al. performed optimization using the Feasible Arc Interior Point Algorithm (FAIPA) to derive the maximum loss factor [22]. El Hafidi et al. optimized patch location and improved algorithm convergence through genetic algorithms and Latin Hypercube Sampling (LHS) algorithms [23]. Askar et al. used a genetic algorithm to optimize the position of the circular aluminium patch [24]. The literature review indicates that various algorithms have been used to optimize the position of the passive patch. However, a simple and quick design method is required to determine the optimal position of a passive patch in real industrial fields.
1.2. Objectives
In this paper, a method to optimize the position of a passive patch with a certain length and thickness is introduced to 1D structures, especially for use with cantilevered beams. First, the method of obtaining the frequency response, natural frequency, and mode loss coefficient is described, which is based on the analytical model for beams with passive patches expressed by complex stiffness. Next, the change in the natural frequency and the loss factor for each mode of the passive patch of a certain length are examined.
Although the position of the passive patch can be determined using the above method, it would be simpler to use the beam shape function. Considering the wide frequency range, the sum of squares using the bending shape function of the beam is obtained together with the modal contribution by the specific excitation range. Subsequently, the position of the appropriate patch is determined and then verified through experiments using the predicted results.
This paper is organized as follows. Section 2 describes the approximate model of the existing passive patch, and Section 3 analyses and explains the characteristics of the passive patch through simulation. Then, the optimal position of the passive patch is determined by using the sum of squares of the proposed bending shape function, and the performance of the designed passive patch is analysed. Finally, Section 4 discusses conclusions and future plans.
2. Modeling
2.1. Beam with a Patch
A cantilever beam model with a passive patch is shown in Figure 1.
[figure(s) omitted; refer to PDF]
In a thin Euler beam of fixed length
Here, the lower beam is defined as layer 3, the viscoelastic layer as layer 2, and the constraint layer as layer 1. Figure 2 shows the deformation due to bending of each layer. The subscript denotes the layer number,
[figure(s) omitted; refer to PDF]
2.2. Displacement Vector
The motion of each layer was investigated by Kung and Singh [5, 6]. The displacement vector
The displacement vector
Let us assume that the bending displacement
Here,
2.3. Mass Matrix and Stiffness Matrix
In the case of inertia matrix H, it is a matrix derived in the process of defining the mass matrix. First of all, kinetic energy is defined by shape function and weight as follows:
In this equation, the generalized mass is
Using the shape function vector, the mass matrix can be expressed as shown, and the inertia matrix H is defined based on this equation:
The mass matrix
Here, the inertia matrix
Thus, the kinetic energy of equation (11) is finally expressed as follows. The relationship between the displacement vector
In the case of strain energy (potential energy), the displacement is restored by the deformation in the vibrating beam and converted into motion. In the case of a linear elastic body, the energy is expressed as the product of the force and the strain, such that
Here, the differential operator
Equation (6) is summarized as follows through equation (2):
Here, the stiffness matrix
For each layer, both the mass matrix and the inertia matrix are added to obtain the kinetic energy and strain energy of the whole, and the integral range corresponds to the length of each layer. The mass matrix M and the stiffness matrix K for the entire layer are defined as follows:
By substituting equation (17) into equations (11) and (14), the kinetic energy and strain energy for the whole system are calculated.
2.4. Approximation
When an object is assumed to have N vibration modes, its degree of freedom is N. Since the beam with several passive patches has a multiple number of subparts including base layer, adhesives, and patches, the total degree of freedom would be increased by the multiple of part numbers. Therefore, to simplify the problem, it is necessary to reduce the degree of freedom for calculation. Here, it is assumed that the motion of the passive patch is determined with respect to the bending shape function of the base layer. First, in the case of the base layer, the Euler beam is fixed on one side. For the beam, the eigenvalue can be analytically calculated through the characteristic equation and then the normalized shape function can be obtained.
For the remaining shape functions, the Rayleigh–Ritz method using strain energy can be expressed as a linear combination of the permissible function satisfying the boundary condition, or the natural frequency can be approximated without solving the complex eigenvalue problem through the weak-core hypothesis.
First, the relationship of motion between layers is considered a weak-core assumption, [21] is applied as the modulus of elasticity of the middle viscoelastic layer, it is smaller than that of the beam, and the constraint layer in the structure of the laminated layer in which the axial load is applied. The longitudinal displacement of layer 1 and layer 3 has the following relationship:
Integrating equation (19) with
[figure(s) omitted; refer to PDF]
2.5. Natural Frequency and Loss Factor
The natural frequency and mode loss factor for each mode can be obtained from the strain energy and kinetic energy obtained previously. First, the loss factor is expressed as complex stiffness in the stiffness matrix. The complex modulus of elasticity is expressed as
At this time, as the response is assumed to be a harmonic response, the complex eigenvalue problem in free oscillation can be written as follows:
In this case, as the stiffness matrix has a frequency dependent characteristic, the eigenvalue converges through iterative calculation. In equation (24),
2.6. Forced Vibration by Disturbance
When the disturbance is applied to a point of the beam, it is assumed that only the bending is generated and the disturbance vector
When disturbance in the form of harmonic function acts on a point
Then, the disturbance vector
Here, the Fourier transform can be taken to calculate the frequency response.
3. Simulation and Experiment
3.1. Loss Coefficient Variation
First, simulation was performed on the length of a passive patch in order to check how the loss of each mode changes depending on the position of the passive patch. The material, properties, and shape of the lower beam and passive patches were determined as shown in Table 1, with reference to the viscoelastic layer used in Plattenburg et al. [12].
Table 1
The physical properties and shape of each layer.
Constrained | Viscoelastic layer | Beam | Unit | |
Material | Aluminium | Adhesive | Steel | |
Modulus of elasticity | MPa | |||
Density | ||||
Poisson Ratio | ||||
Loss factor | ||||
Thickness | mm | |||
Length | mm |
The natural frequencies calculated for beams without passive patches are given in Table 2. The first target is the vibration attenuation for the five modes of the beam, with the patch designed to attenuate vibrations of 0–1000 [Hz]. The length
Table 2
Natural frequency of beam.
Unit: (Hz) | Mode 1 | Mode 2 | Mode 3 | Mode 4 | Mode 5 |
Natural frequency | 14.9 | 93.3 | 261.2 | 511.7 | 845.9 |
[figure(s) omitted; refer to PDF]
When the mode shape of the beam is viewed, the shortest distance between nodes is mode 5 and the distance corresponds to a normalized length of 0.2. Therefore, the normalized length corresponding to 1/2 of the distance between nodes is determined as 0.1.
This condition enables the simulation of the manner in which the loss factor for each mode is affected by the position of the patch. The position of the patch has a finite length, so it shows when the position changes from 0.01 to 0.95 from the normalization position of 0.05. Figure 5 shows the second derivative of the mode shapes. For each mode, the correlation between the magnitude of the second-order differential absolute value
[figure(s) omitted; refer to PDF]
In Figure 6, the loss factor for the 1st and 2nd modes and the curvature of the beam are shown for example. Similar trends have been observed for 3rd, 4th, and 5th modes as well. It is confirmed that the magnitude of the absolute value of the second derivative
[figure(s) omitted; refer to PDF]
Figures 7 and 8 show the variation of the natural frequency according to the position of the passive patch. Additionally, Table 3 summarizes the natural frequency changes according to the patch location. It is observed that the value of the natural frequency changes greatly as the degree of the mode increases. In addition, when the passive patch is installed near the fixed end, the natural frequency is observed to be high in all modes, whereas when it is attached near the free end, it is confirmed that the natural frequency is lowered.
[figure(s) omitted; refer to PDF]
Table 3
Natural frequency change according to patch location.
Peak (Hz) | Mode 1 | Mode 2 | Mode 3 | Mode 4 | Mode 5 |
Without patch | 15 | 93 | 261 | 512 | 848 |
Located in 0.5 | 15 | 91 | 260 | 504 | 838 |
Change | 0.00% | −2.15% | −0.38% | −1.56% | −1.18% |
Located in 0.82 | 15 | 93 | 260 | 507 | 839 |
Change | 0.00% | 0.00% | −0.38% | −0.98% | −1.06% |
3.2. Optimal Patch Location
The influence of the curvature of the beam was confirmed. Thus, the values for the curvature of the beam are utilized to design the patch. The position
If the value of the excitation magnitude
Table 4
Mode contributions for each mode.
Mode 1 | Mode 2 | Mode 3 | Mode 4 | Mode 5 | |
Mode contribution | 0.02 | 0.12 | 0.30 | 0.53 | 0.78 |
For mode contribution, mode 4 and mode 5 are large. Each mode contribution is weighted and multiplied by the second derivative
Using the mode contributions calculated in Table 4 and the values in Figure 5, the sum of squares of the shape functions can be plotted as shown in Figure 9. In this case, the position of the passive patch can be selected as 0.19, 0.41, 0.59, 0.82 except for the normalized positions 0 and 1 given the length of the patch is finite. However, as the size is largest at 0.82, the optimum patch position is determined to be 0.82. In order to compare the effect of the patch position, two cases of passive patches with the normalized length of 0.82 and the low value of 0.5 are compared to predict the performance of the passive patch by simulation. In this case, 0.5 is selected because passive patches cannot be installed in the case of 0.08.
[figure(s) omitted; refer to PDF]
3.3. Simulation of Attenuation Performance
The passive patch attenuation performance at the two selected positions is simulated by the loss factor and the reduced peak size. First, loss factors for each mode at two locations are compared. The loss factors at each location are given in Table 5.
Table 5
Loss factor for each mode.
Patch location | Mode 1 | Mode 2 | Mode 3 | Mode 4 | Mode 5 |
0.82 | 0.0002 | 0.0010 | 0.0028 | 0.0042 | 0.0032 |
0.5 | 0.0015 | 0.0025 | 0.0002 | 0.0030 | 0.0009 |
Next, the frequency spectrum predicted from 0 to 1000 Hz at the observation point is shown. The observation point was selected as the normalization position of 0.375. Figure 10 shows the simulation of the accelerance from equation (29) for undamped beams and passive patches in two selected cases. The loss tends to be the same as the result of the loss factor, and it can be confirmed that the peak size is 0.82 at the resonance frequency except for mode 2. In addition, it is confirmed that a large attenuation is invoked in modes 3, 4, and 5 when a passive patch is attached at a position of 0.82. In the case of the natural frequency, it is confirmed that the stiffness and the mass of the system are changed by attaching the passive patch, and the natural frequency is decreased accordingly. That is, it can be seen that the effect of mass is greater than that of stiffness. The natural frequency does not drop much, but if the excitation at that frequency is large, the passive patch should be avoided. The size of the reduced peak produced by attaching the passive patch is given in Table 6. The data written in the table indicates the decibel size before attachment and at position 2 and the reduction amount at the resonance frequency corresponding to each mode. Therefore, the frequencies at the compared peaks are all different.
[figure(s) omitted; refer to PDF]
Table 6
Peak-to-peak of each mode for manual patching in both cases.
Peak (dB) | Mode 1 | Mode 2 | Mode 3 | Mode 4 | Mode 5 |
W/o patch | −6.16 | 24.53 | 33.33 | 25.39 | 43.7 |
With 0.5 | −25.87 | 8.394 | 30.5 | 14.01 | 39.09 |
Change | 19.71↓ | 16.136↓ | 2.83↓ | 11.38↓ | 4.61↓ |
With 0.82 | −34.69 | 20.12 | 22.7 | 12.82 | 33.2 |
Change | 28.53↓ | 4.41↓ | 10.63↓ | 12.57↓ | 10.5↓ |
In Table 6, the reduction of the peak is compared with the resonance frequency in one mode, and it is confirmed that attenuation is large when the loss coefficient is large, except for mode 1 (with the patch at 0.82). In Figure 10, it can be observed that mode 1 has relatively small amplitude compared to the other modes and the amplitude level in the time domain is not much affected to those modes. However, if one passive patch is compared with the other modes, the loss factor is not necessarily large and the peak decrease is not always large.
3.4. Experimental Validation
Next, the effect of the position of the passive patch in the two selected cases was verified by experiments. Figure 11 shows the experimental equipment. An accelerometer is mounted on a thin beam fixed to the vise, and an impact hammer is used to generate the impulse. The signal from the accelerometer is received from the data collector and displayed on the monitor through signal processing. The sampling frequency is 2000 Hz, observed from 0 Hz to 1000 Hz in total, and the frequency resolution is 0.1 Hz.
[figure(s) omitted; refer to PDF]
Figure 12 shows the position of the beam on the beam and the observation position of the response. In the case of excitation, it is assumed that a constant probability distribution is applied in the range of the normalization length of 0.1. Therefore, the excitation position is divided into three parts, and averaging is performed. Figure 13 shows the attached passive patch.
[figure(s) omitted; refer to PDF]
Figure 14 shows the acceleration measured by the accelerometer. In this case, it is possible to observe that a different peak appears from the simulation. This is because the length is longer than 10 times the width, but other modes such as twist have also appeared in the region above 250 Hz. If the same results with simulation need to be obtained through the experiment, the system should be modelled by a thin plate model. In addition, the clearly appeared modes besides bending modes are because of the contact condition of beam and vise, which is an incomplete supporting condition exciting other structures such as vise, vibration table, etc. The yellow circles indicate the bending mode, and it is confirmed that the first to fifth modes are displayed in order. As with the simulation, it is confirmed that the natural frequency of each mode is reduced by attaching the passive patch.
[figure(s) omitted; refer to PDF]
Also, Table 7 lists the peak magnitude at resonance frequency in decibels for each mode and the attenuation performance when attached at the normalization position of 0.5 compared to the normalization position of 0.8 for mode 1 and mode 2. However, for modes 3, 4, and 5, it is confirmed that the passive patch attached to 0.82 shows much better attenuation performance. As the mode contribution is large in modes 3, 4, and 5, it is targeted mainly at the high modes, and the result is also the result of the experiment. In mode 4, it is confirmed that large attenuation occurs. This is because the resonance frequency of the twist mode near 500 Hz, which is the resonance frequency of mode 4, is reduced by about 30 Hz with the passive patch attachment.
Table 7
Peak-to-peak and size reduction for each mode for manual patching in both cases.
Peak (dB) | Mode 1 | Mode 2 | Mode 3 | Mode 4 | Mode 5 |
W/o patch | −2.72 | 26.15 | 35.52 | 27.21 | 30.67 |
With 0.5 | −9.13 | 12.67 | 29.61 | 10.58 | 27.02 |
Change | 6.41↓ | 13.48↓ | 5.91↓ | 16.63↓ | 6.23↓ |
With 0.82 | −9.02 | 18.64 | 19.52 | 8.26 | 22.51 |
Change | 6.3↓ | 7.51↓ | 16↓ | 18.95↓ | 10.74↓ |
Figure 15 compares the peak-to-peak values obtained through experiments and simulations. For the positions of each passive patch, the experiment and the simulation are similar in the remaining areas except for mode 1 and there is a larger decrease in the value of the peak in the experiment. This is presumably because the passive patch reduces not only the bending mode but also the other modes. Further, in mode 1, the attenuation in the simulation was large. In the experiment, the resonance frequency of mode 1, which is a small signal, is not well represented by the noise. Figure 16 shows the correlation between the loss factor and attenuation levels in dB scale obtained from simulation and experiment, which obviously shows the same trend except for mode 1 from the simulation.
[figure(s) omitted; refer to PDF]
Figure 17 shows the frequency spectrum on a linear scale. This metric can be used to determine the RMS value for measuring the overall vibration attenuation, and its value is given in Table 8. Comparing the case where the passive patch is not attached and the case where the passive patch is attached at 0.5 position, it is confirmed that the vibration of about 27% is totally reduced.
[figure(s) omitted; refer to PDF]
Table 8
RMS reduction for manual patching in both cases.
RMS | Total |
Before attachment | 9.62 |
With 0.5 | 7.04 |
Change | 2.58 (26.8%↓) |
With 0.82 | 5.59 |
Change | 4.03 (41.9%↓) |
In addition, it is confirmed that the size of the RMS is further reduced to 41.9% when it is attached to the normalization position 0.82. Amplitude attenuation occurs not only in bending but in other modes as well. When the peak and RMS size are reduced, the design of the passive patch is considered appropriate.
4. Conclusion
To optimize the position of the passive patch, the sum of squares of the bend shape and the position of the passive patch are used. Further, the effect of the passive patch is verified by using the existing passive patch model.
First, the model expression of the passive patch is examined. The relationship between the passive patch and the beam is investigated in detail, and the loss coefficient and the frequency spectrum due to the natural frequency and the forced vibration in the presence of several passive patches are numerically simulated.
Next, in order to determine the position of the passive patch, the change in the loss coefficient and natural frequency according to the position is examined. It is confirmed that the loss factor is dependent on the curvature which is the second derivative of the bending mode shape. The position of the passive patch is determined through the sum of squares value expressed as a linear combination of mode shape and mode contribution. Passive patches of constant length and thickness are designed in this way. Weighting is applied to the case where the mode contribution is large so that the attenuation effect is enhanced in a mode in which a large response is expected. It is confirmed that the natural frequency is lowered for each mode due to the passive patch changing the vibration system.
In order to verify the performance of the positionally determined passive patch, two cases are compared. It is assumed that one passive patch is designed to have a constant length on one cantilevered beam. In this case, the passive patch attenuates the overall vibration, and the peak-to-peak value also decreases regardless of position. However, it can be seen that the size of the response is greatly reduced in the case of the passive patch, determined by obtaining the sum of squares using the shape function. Experiments were conducted to verify the effectiveness of passive patches. Experimental results show that the frequency response in mode 1 is small and difficult to observe. Because the experiment involves a three-dimensional mode of vibration, other peaks also appear, which is different from the simulation. The attenuation effect on the bending of the passive patch was not accurately observed, while the natural frequency was shifted by the passive mode such as the twist mode.
Future research should investigate applying the passive patch design method to the actual vibration system by the excitation force of various frequency spectrums. In this study, a certain size is assumed and used to verify the damping effect using the proposed method considering the mode shape and frequency of the actual model.
In addition, it is necessary to study the optimization method of the position design in installing passive patches as well as active patches using the piezoelectric element. Passive patches are effective at high frequencies, so weights can be applied to achieve optimal vibration damping along with active patches.
The passive patch location design method proposed in this paper is expected to contribute to the improvement of the practical application of passive patches without the need for complicated processes. In addition, if applied to real machine systems with active control, this method will contribute to the research corpus on the topic of next generation vibration reduction systems.
Acknowledgments
This work was supported by the 2023 Yeungnam University Research Grant (223A380081) and by Basic Science Research Program through the National Research Foundation of Korea (NRF) funded by the Ministry of Education (NRF-2022R1F1A1076089).
[1] M. D. Rao, "Recent applications of viscoelastic damping for noise control in automobiles and commercial airplanes," Journal of Sound and Vibration, vol. 262 no. 3, pp. 457-474, DOI: 10.1016/s0022-460x(03)00106-8, 2003.
[2] B. Baran, Y. Yesilce, S. Catal, "Free vibrations of axial-loaded beams resting on viscoelastic foundation using Adomian decomposition method and differential transformation," Engineering Science and Technology, an International Journal, vol. 73 no. 2, pp. 109-121, 2020.
[3] B. Bozyigit, Y. Yesilce, M. Abdel Wahab, "Single variable shear deformation theory for free vibration and harmonic response of frames on flexible foundation," Engineering Structures, vol. 208,DOI: 10.1016/j.engstruct.2020.110268, 2020.
[4] B. Baran, Y. Yesilce, M. Abdel Wahab, "Transfer matrix formulations and single variable shear deformation theory for crack detection in beam-like structures," Structural Engineering and Mechanics, vol. 73 no. 2, pp. 109-121, 2020.
[5] B. Baran, Y. Yesilce, M. Abdel Wahab, "Free vibration and harmonic response of cracked frames using a single variable shear deformation theory," Structural Engineering and Mechanics, vol. 74 no. 1, pp. 33-54, 2020.
[6] L. Irazu, M. J. Elejabarrieta, "The influence of viscoelastic film thickness on the dynamic characteristics of thin sandwich structures," Composite Structures, vol. 134, pp. 421-428, DOI: 10.1016/j.compstruct.2015.07.086, 2015.
[7] A. Benjeddou, "Advances in hybrid active-passive vibration and noise control via piezoelectric and viscoelastic constrained layer treatments," Journal of Vibration and Control, vol. 7 no. 4, pp. 565-602, DOI: 10.1177/107754630100700406, 2001.
[8] M. A. Trindade, A. Benjeddou, "Hybrid active-passive damping treatments using viscoelastic and piezoelectric materials: review and assessment," Journal of Vibration and Control, vol. 8 no. 6, pp. 699-745, DOI: 10.1177/1077546029186, 2002.
[9] A. K. Lall, N. T. Asnani, B. C. Nakra, "Damping analysis of partially covered sandwich beams," Journal of Sound and Vibration, vol. 123 no. 2, pp. 247-259, DOI: 10.1016/s0022-460x(88)80109-3, 1988.
[10] A. K. Lall, N. T. Asnani, B. C. Nakra, "Vibration and damping analysis of rectangular plate with partially covered con-strained viscoelastic layer," Journal of Vibration and Acoustics, vol. 109 no. 3, pp. 241-247, DOI: 10.1115/1.3269427, 1987.
[11] S. W. Kung, R. Singh, "Vibration analysis of beams with multiple constrained layer damping patches," Journal of Sound and Vibration, vol. 212 no. 5, pp. 781-805, DOI: 10.1006/jsvi.1997.1409, 1998.
[12] S. W. Kung, R. Singh, "Complex eigensolutions of rectangular plates with damping patches," Journal of Sound and Vibration, vol. 216 no. 1,DOI: 10.1006/jsvi.1998.1644, 1998.
[13] S. W. Kung, R. Singh, "Development of approximate methods for the analysis of patch damping design concepts," Journal of Sound and Vibration, vol. 219 no. 5, pp. 785-812, DOI: 10.1006/jsvi.1998.1876, 1999.
[14] J. Plattenburg, J. T. Dreyer, R. Singh, "Active and passive damping patches on a thin rectangular plate: a refined analytical model with experimental validation," Journal of Sound and Vibration, vol. 353 no. 29, pp. 75-95, DOI: 10.1016/j.jsv.2015.05.026, 2015.
[15] S. Tian, Z. Xu, Q. Wu, C. Qin, "Dimensionless analysis of segmented constrained layer damping treatments with modal strain energy method," Shock and Vibration, vol. 2016,DOI: 10.1155/2016/8969062, 2016.
[16] B. Khalfi, A. Ross, "Influence of partial constrained layer damping on the bending wave propagation in an impacted viscoelastic sandwich," International Journal of Solids and Structures, vol. 50 no. 25-26, pp. 4133-4144, DOI: 10.1016/j.ijsolstr.2013.07.023, 2013.
[17] H. Zheng, C. Cai, X. M. Tan, "Optimization of partial constrained layer damping treatment for vibrational energy minimization of vibrating beams," Computers and Structures, vol. 82 no. 29-30, pp. 2493-2507, DOI: 10.1016/j.compstruc.2004.07.002, 2004.
[18] H. Zheng, C. Cai, G. S. H. Pau, G. R. Liu, "Minimizing vibration response of cylindrical shells through layout optimization of passive constrained layer damping treatments," Journal of Sound and Vibration, vol. 279 no. 3-5, pp. 739-756, DOI: 10.1016/j.jsv.2003.11.020, 2005.
[19] Y. Lei, W. Zheng, Q. Huang, C. Li, "Topology optimization of passive constrained layer damping on plates with respect to noise control," Advanced Materials Research, vol. 774-776,DOI: 10.4028/www.scientific.net/amr.774-776.3, 2013.
[20] W. Zheng, Y. Lei, S. Li, Q. Huang, "Topology optimization of passive constrained layer damping with partial coverage on plate," Shock and Vibration, vol. 20 no. 2, pp. 199-211, DOI: 10.1155/2013/360327, 2013.
[21] Z. Fang, "Topology optimization approach of constrained layer damping layout using level set method," International Congress on Sound and Vibration, vol. 18, 2014.
[22] A. L. Araújo, P. Martins, C. M. Mota Soares, C. A. Mota Soares, J. Herskovits, "Damping optimization of viscoelastic laminated sandwich composite structures," Structural and Multidisciplinary Optimization, vol. 39 no. 6, pp. 569-579, DOI: 10.1007/s00158-009-0390-4, 2009.
[23] A. El Hafidi, C. D. L. P. Herrero, B. Martin, "Optimization of passive constrained layer damping (PCLD) treatments for vibration reduction," Journal of Vibroengineering, vol. 17 no. 6, pp. 3035-3045, 2015.
[24] E. Askar, E. Elsoaly, M. Kamel, H. Kamel, "Optimization of passive vibration damping of space structures," International journal of mechanical, aerospace, industrial, mechatronic and manufacturing engineering, vol. 11, 2017.
[25] E. M. Kerwin, Kerwin, "Damping of flexural waves by a constrained viscoelastic layer," Journal of the Acoustical Society of America, vol. 31 no. 7, pp. 952-962, DOI: 10.1121/1.1907821, 1959.
You have requested "on-the-fly" machine translation of selected content from our databases. This functionality is provided solely for your convenience and is in no way intended to replace human translation. Show full disclaimer
Neither ProQuest nor its licensors make any representations or warranties with respect to the translations. The translations are automatically generated "AS IS" and "AS AVAILABLE" and are not retained in our systems. PROQUEST AND ITS LICENSORS SPECIFICALLY DISCLAIM ANY AND ALL EXPRESS OR IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, ANY WARRANTIES FOR AVAILABILITY, ACCURACY, TIMELINESS, COMPLETENESS, NON-INFRINGMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Your use of the translations is subject to all use restrictions contained in your Electronic Products License Agreement and by using the translation functionality you agree to forgo any and all claims against ProQuest or its licensors for your use of the translation functionality and any output derived there from. Hide full disclaimer
Copyright © 2024 Dongwoo Hong et al. This is an open access article distributed under the Creative Commons Attribution License (the “License”), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited. Notwithstanding the ProQuest Terms and Conditions, you may use this content in accordance with the terms of the License. https://creativecommons.org/licenses/by/4.0/
Abstract
When the thickness of a structure is reduced to decrease weight, it may experience structural vibration and disturbance. The use of passive patches is effective in addressing this issue when the loss factor is small or when space and weight are restricted. The greatest attenuation occurs when passive patches are used across the entire coverage area. However, passive patches of reasonable size must be affixed to ensure that they are effective in terms of cost and design. In this paper, the sum of squares’ value for the bending mode shape is used to determine the location of a small passive patch to achieve vibration damping for multiple modes. Under the condition of forced vibration, the modal contribution of each mode is obtained. Using this contribution as a weight, the optimal position of the passive patch is determined as the maximum value obtained in the form of a linear combination multiplied by the curvature of the beam. Simulation and experiment were used to test the efficacy of the location determined for passive patches. It was determined that, depending on the location of the passive patch, the peak amplitude at the natural frequency of each mode decreased significantly, validating the effectiveness of the design method.
You have requested "on-the-fly" machine translation of selected content from our databases. This functionality is provided solely for your convenience and is in no way intended to replace human translation. Show full disclaimer
Neither ProQuest nor its licensors make any representations or warranties with respect to the translations. The translations are automatically generated "AS IS" and "AS AVAILABLE" and are not retained in our systems. PROQUEST AND ITS LICENSORS SPECIFICALLY DISCLAIM ANY AND ALL EXPRESS OR IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, ANY WARRANTIES FOR AVAILABILITY, ACCURACY, TIMELINESS, COMPLETENESS, NON-INFRINGMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Your use of the translations is subject to all use restrictions contained in your Electronic Products License Agreement and by using the translation functionality you agree to forgo any and all claims against ProQuest or its licensors for your use of the translation functionality and any output derived there from. Hide full disclaimer
Details

1 Daegu Mechatronics & Materials Institute, 32, Seongseogongdan-ro 11-gil, Dalseo-gu, Daegu 42714, Republic of Korea
2 Neuros Co. Ltd., Daejeon-si 34027, Republic of Korea
3 School of Mechanical Engineering, Yeungnam University, Gyeongsan-si 38541, Republic of Korea