Tunable Multiwavelength SOA-Based Fiber Laser

Abstract

Tunable multiwavelength fiber lasers based on semiconductor optical amplifiers (SOA) have received attracting interest due to their wide prospective applications in dense division multiplexing (DWDM) systems and optical sensing. Using an SOA in a nonlinear optical loop mirror (NOLM), we demonstrate up to 13 lasing peaks by controlling the pump current and the polarization controller. At maximum pump current (450 mA), the emitted multiwavelength is between 1550 nm and 1572 nm with a wavelength spacing of 1.87 nm and 3 dB output linewidth of 0.8 nm with an output power of −7 dBm and 27 dB optical signal-to-noise ratio (OSNR). The multiwavelength output power and multiwavelength peak stability are investigated, and it was found that the power fluctuation of each multiwavelength line is less than 0.2 dB. In addition, by adjusting the polarization controllers (PCs) and SOA temperature, we obtained a tunable multiwavelength emission. The proposed fiber laser offers advantages such as simple structure, low loss, and long-time stable and multiwavelength emission.

1. Introduction

Tunable multiwavelength fiber laser has received attractive interest due to their wide prospective applications in optical communication and optical sensing. The broadband, high extinction ratio and fast switching time-like advantages of semiconductor optical amplifier (SOA) make it an attractive lasing source for multiwavelength generations.

Multiwavelength emission has been achieved using different fiber laser sources, including erbium-doped fiber laser (EDFL) [1,2,3,4,5], Raman lasers [6,7], and hybrid Raman and erbium-doped fiber [8,9]. However, the homogeneous line broadening and mode competition were the main challenges for generating a stable dual- and multiwavelength operation at room temperature, even with our recent research work on dual-wavelength lasing for 5G and LiDAR applications [10,11,12,13]. In addition, many other techniques have been used for improving the EDFL multiwavelength stability, such as cooling the EDF down to cryogenic temperature [14], using a specially designed twin-core EDF [15], using frequency shift feedback [16], using intensity-dependent loss mechanisms like nonlinear fiber loop mirror (NOLM) [17], nonlinear polarization rotation (NPR) [18], incorporating EDF with SOA [19,20].

However, SOA is considered an alternative approach in the fiber laser for multiwavelength emission due to the advantages of low cost, low insertion loss, broad gain spectrum, heterogeneous spectral broadening, and wavelength versatility via bandgap engineering. Subsequently, some demonstrations like SOA-based multiwavelength fiber laser using a nonlinear polarization rotation NPR [21], high birefringence photonic crystal fiber [22], Mach-Zehnder Interferometer [23], and loop mirror interferometer [24] are also reported.

Achieving multiwavelength laser peaks using SOA fiber lasers has numerous advantages in photonics, electronics, sensing, and quantum optics. For instance, it can be used in the implementation of DWDM systems using a single optical source instead of using multiple lasers, navigation, and surveillance-based applications with high resolution and accuracy, like in intelligent transport systems-related industries and smart agriculture sensing systems.

Moreover, this multiwavelength fiber laser is suitable for 5G communication, LiDAR sensing-related applications [10,11,12,13], and especially in the field of quantum information processing and quantum communication [25,26,27].

Furthermore, the obtained results of the demonstrated multiwavelength fiber laser open new windows to extend its application areas in a multiwavelength quantum key distribution (QKD) system that has the advantage of involving and adding multiple wavelengths for different protocols and data exchange [25,26,27]. It is also an emulated system with a physical unclonable function that eliminates the need to share a subsection of the final key for eavesdropper detection and allows for ternary and quaternary data transmission.

However, the main issue with the SOA is its high sensitivity to the optical reflection from the cavity. It causes the generation of gain ripple, which is dependent on multiwavelength emission.

To mitigate this issue, we used two ring cavities linked through an optical circulator to design a unidirectional, tunable, and stable SOA-based multiwavelength fiber laser in a nonlinear loop mirror (NOLM) configuration at room temperature. By controlling the pump current and PCs, we attained up to 13 lasing peaks with a wavelength spacing of 1.86 nm, output linewidth of 0.8 nm, output optical power of −7 dBm, and OSNR ~ 27 dB. The attained wavelength spacing of 1.86 nm is convertible to corresponding millimeter waves (mmW) of 230 GHz [10], which ensures the capability of the proposed lasing source to be used for applications like dense wavelength division multiplexing, optical sensors spectroscopy, microwave generation, optical instrument testing, 5G/6G networks, and LiDAR systems.

2. Experimental Setup

The experimental setup of the SOA-based fiber laser for the generation of tunable multiwavelengths consists of two ring cavities, as shown in Figure 1.

The primary ring cavity comprises the SOA and a polarization controller (PC). The SOA is pumped using a pump current driver and TEC controller; it achieves a peak gain at 1535 nm in this cavity with a spectral bandwidth of 80 nm and a small signal gain of 25 dB at room temperature. The Babinet–Soleil compensator polarization controller (PC1) is used to optimize the polarization state of the cavity.

The second ring cavity (NOLM) consists of 2 × 2 fused couplers with a 55/45 coupling ratio, which splits light into two unequal portions, traveling in opposite directions through the loop mirror. It also contains 1 m of polarization-maintaining fiber (PMF) and 7 m of standard telecom fiber (SMF). An optical circulator connects both cavities and ensures the unidirectional flow of light in the primary cavity. The second polarization controller (PC2) also maintains the polarization state of the second cavity. Further, a 90:10 optical fiber coupler provides an output power of 10% for measurements and analysis using an optical spectrum analyzer (OSA) at a resolution of 0.05 nm, and 90% is redirected to the primary ring.

3. Results and Discussion

The multiwavelength emitted from the proposed fiber laser is analyzed using an optical spectrum analyzer at different pump currents of the SOA device. First, the laser system emitted a single wavelength at an SOA pump current of 88 mA while carefully adjusting the PC₂ in the loop mirror cavity. By slightly increasing the SOA pump current to 89.5 mA, a dual-wavelength laser peak and a triple laser peak at 91.5 mA are observed with OSNR ~ 18 dB, as shown in Figure 2. Additionally, fourth to seventh multiwavelength lasing lines are achieved by gradually increasing the SOA pump current from 96 mA to 150 mA with OSNR ~ 24 dB. We have achieved about 13 lasing peaks (1550 nm–1572 nm) at 450 mA with a wavelength spacing of 1.87 nm, OSNR ~ 27 dB, and a 3-dB bandwidth of 0.8 nm (Figure 2).

Figure 3 shows the central wavelengths of the proposed SOA fiber laser at different pump currents. The attained multiwavelengths are observed, initially on both sides of the central wavelength lasing. However, the peak of the first wavelength laser is shifted to the long wavelength region when the pump current of the SOA increases from 96 mA to 110 mA. This is because the saturated gain peak of SOA lies in the long wavelength region (~1560 nm). SOA signal–gain saturation is caused by a reduction in the population inversion in the active layer due to an increase in stimulated emission (lasing emission).

Moreover, we keep the pumping below the pumping current of 500 mA in our experiments to avoid any unstable generation of multiwavelength peaks shown in Figure 4. The SOA lasing threshold is about 70 mA. Then, increased linearly can be seen for up to 150 mA; after that, the output power increased exponentially due to SOA gain saturation at a high pump current. It is also observed that the gain medium of SOA effectively improves the stability of the multiwavelength lasing operation. Moreover, the double-ring structure of the proposed laser reshapes the transmission spectrum and generates lasing peaks with narrow channel spacing.

As SOA is polarization-dependent, the output spectra are tunable (Figure 5) either to the shorter wavelength by decreasing the temperature of the SOA device to 18 °C or the longer wavelength by increasing the SOA temperature to 23 °C and controlling the state of polarization in the laser cavity and loop mirror. SOA temperature is controlled using a TEC controller (thermoelectric/Peltier module) in the combined laser diode and TEC controllers. The TEC controller first determines the desired temperature setpoint and then applies the appropriate electric current needed to achieve the desired temperature.

The stability of the output optical power and wavelength peaks are investigated to the time, as shown in Figure 6 and Figure 7, respectively. The optical power fluctuations of ~0.2 dB are observed after 6 h. Moreover, a shift of 0.059 nm in wavelength peaks is observed after 3 h with the pumping of 300 mA at room temperature. The SOA temperature is controlled by the received feedback from a temperature sensor; accordingly, there is a very small shift (0.059 nm) in wavelength peaks due to the temperature fluctuations in the device over the investigation time (3 h).

4. Conclusions

We have demonstrated a tunable multiwavelength SOA laser based on an NOLM double-ring cavity structure. Multiwavelength lasing with equal channel spacing and 3-dB bandwidth of 1.87 nm and 0.8 nm, respectively, are achieved. The experimental results have also shown that the output optical power and wavelength peaks are flat and quite stable for a long time at room temperature, with a peak power fluctuation of each multiwavelength line of less than 0.2 dB. The source has an average peak power of about −7 dBm and OSNR of about 27 dB at pump current between 220 mA and 450 mA, which makes this source a good choice for dense division multiplexing and low-cost microwave generation.

Author Contributions

H.J.K. creation of the idea, conceptualization, methodology, validation, and writing—original draft preparation, V.S. and S.V.S. conceptualization, review, and editing of the manuscript. All authors have read and agreed to the published version of the manuscript.

Data Availability Statement

Data available based on request.

Acknowledgments

We acknowledge support from UK EPSRC (EP/W002868/1), and Horizon 2020 ETN MEFISTA (861152).

Conflicts of Interest

The authors declare no conflict of interest.

Footnotes

Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to people or property resulting from any ideas, methods, instructions or products referred to in the content.

Figures

Figure 1. The experimental setup of the multiwavelength SOA fiber laser.

Figure 2. Multiwavelength emission from SOA fiber laser at different pump currents.

Figure 3. The emitted wavelength peaks vs. the pump current.

Figure 4. The multiwavelength SOA fiber laser outputs optical power.

Figure 5. The multiwavelength SOA fiber laser tunability operating regimes at different SOA temperatures.

Figure 6. Output optical power stability over 6 h.

Figure 7. The multiwavelength peaks stability at pump current of 300 mA over 3 h.

References

1. Zhao, Z.; Li, X.; Li, Y.; Qin, H.; Wang, H.; Luo, Y.; Yan, Z.; Sun, Q.; Liu, D.; Zhang, L. Multiwavelength Er-doped fiber laser using an all-fiber Lyot filter. Appl. Opt.; 2018; 57, pp. 9270-9274. [DOI: https://dx.doi.org/10.1364/AO.57.009270]

2. Moon, D.S.; Paek, U.-C.; Chung, Y. Multi-wavelength lasing oscillations in an erbium-doped fiber laser using few-mode fiber Bragg grating. Opt. Express; 2004; 12, pp. 6147-6152. [DOI: https://dx.doi.org/10.1364/OPEX.12.006147] [PubMed: https://www.ncbi.nlm.nih.gov/pubmed/19488258]

3. Zhao, Q.; Pei, L.; Zheng, J.; Tang, M.; Xie, Y.; Li, J.; Ning, T. Switchable Multi-Wavelength Erbium-Doped Fiber Laser with Adjustable Wavelength Interval. J. Light. Technol.; 2019; 37, pp. 3784-3790. [DOI: https://dx.doi.org/10.1109/JLT.2019.2920840]

4. He, W.; Zhang, W.; Zhu, L.; Lou, X.; Dong, M. C-band switchable multi-wavelength erbium-doped fiber laser based on Mach–Zehnder interferometer employing seven-core fiber. Opt. Fiber Technol.; 2018; 46, pp. 30-35. [DOI: https://dx.doi.org/10.1016/j.yofte.2018.08.011]

5. Tang, M.; Jiang, Y.; Li, H.; Zhao, Q.; Cao, M.; Mi, Y.; Wu, L.; Jian, W.; Ren, W.; Ren, G. Multi-wavelength erbium-doped fiber laser with tunable orbital angular momentum mode output. J. Opt. Soc. Am. B; 2020; 37, 834. [DOI: https://dx.doi.org/10.1364/JOSAB.383889]

6. Kim, N.S.; Zou, X.; Lewis, K. CW depolarized multiwavelength Raman fiber ring laser with over 58 channels and 50 GHz channel spacing. Proceedings of the Optical Fiber Communication Conference; Anaheim, CA, USA, 17 March 2002; [DOI: https://dx.doi.org/10.1109/ofc.2002.1036617]

7. El-Taher, A.E.; Harper, P.; Babin, S.A.; Churkin, D.V.; Podivilov, E.V.; Ania-Castanon, J.D.; Turitsyn, S.K. Effect of Rayleigh-scattering distributed feedback on multiwavelength Raman fibre laser generation. Opt. Lett.; 2011; 36, pp. 130-132. [DOI: https://dx.doi.org/10.1364/OL.36.000130]

8. Chen, D.; Qin, S.; He, S. Channel-spacing-tunable multi-wavelength fiber ring laser with hybrid Raman and Erbium-doped fiber gains. Opt. Express; 2007; 15, pp. 930-935. [DOI: https://dx.doi.org/10.1364/OE.15.000930]

9. Qureshi, K.; Tam, H.Y.; Chung, W.H.; Wai, P.K.A. Multiwavelength Laser Source Using Linear Optical Amplifier. IEEE Phot. Tech. Lett.; 2005; 17, pp. 1611-1613. [DOI: https://dx.doi.org/10.1109/LPT.2005.851912]

10. Kbashi, H.J.; Sharma, V.; Sergeyev, S. Phase-stable millimeter-wave generation using switchable dual-wavelength fiber laser. Opt. Lasers Eng.; 2021; 137, 106390. [DOI: https://dx.doi.org/10.1016/j.optlaseng.2020.106390]

11. Kbashi, H.J.; Sharma, V.; Sergeyev, S. Dual-wavelength fiber-laser-based transmission of millimeter waves for 5G-supported Radio-over-Fiber (RoF) links. Opt. Fiber Technol.; 2021; 65, 102588. [DOI: https://dx.doi.org/10.1016/j.yofte.2021.102588]

12. Sharma, V.; Kbashi, H.J.; Sergeyev, S. MIMO-employed coherent photonic-radar (MIMO-Co-PHRAD) for detection and ranging. Wirel. Netw.; 2021; 27, pp. 2549-2558. [DOI: https://dx.doi.org/10.1007/s11276-021-02605-2]

13. Kbashi, H.J.; Vishal, S.; Sergeyev, S. Transmission of 5G using Tunable Dual-Wavelength Fiber Laser. Proceedings of the 2021 Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe); Munich, Germany, 21–25 June 2021; 1. [DOI: https://dx.doi.org/10.1109/cleo/europe-eqec52157.2021.9541920]

14. Moon, D.-S.; Chung, Y. Multi-wavelength fibre ring laser based on a sampled chirped fibre Bragg grating with a hybrid gain medium. Opt. Commun.; 2012; 285, pp. 1908-1910. [DOI: https://dx.doi.org/10.1016/j.optcom.2011.12.056]

15. Yin, G.; Lou, S.; Wang, X.; Han, B. Tunable multi-wavelength erbium-doped fiber laser by cascading a standard Mach–Zehnder interferometer and a twin-core fiber-based filter. Laser Phys. Lett.; 2013; 10, 125110. [DOI: https://dx.doi.org/10.1088/1612-2011/10/12/125110]

16. Zhou, K.; Zhou, D.; Dong, F.; Ngo, N.Q. Room-temperature multiwavelength erbium-doped fiber ring laser employing sinusoidal phase-modulation feedback. Opt. Lett.; 2003; 28, pp. 893-895. [DOI: https://dx.doi.org/10.1364/OL.28.000893] [PubMed: https://www.ncbi.nlm.nih.gov/pubmed/12816237]

17. Quan, M.; Li, Y.; Tian, J.; Yao, Y. Multifunctional tunable multiwavelength erbium-doped fiber laser based on tunable comb filter and intensity-dependent loss modulation. Opt. Commun.; 2015; 340, pp. 63-68. [DOI: https://dx.doi.org/10.1016/j.optcom.2014.11.090]

18. Sulaiman, A.; Zamzuri, A.; Hitam, S.; Abas, A.; Mahdi, M. Flatness investigation of multiwavelength SOA fiber laser based on intensity-dependent transmission mechanism. Opt. Commun.; 2013; 291, pp. 264-268. [DOI: https://dx.doi.org/10.1016/j.optcom.2012.10.078]

19. Yao, J.; Yao, J.; Deng, Z.; Liu, J. Multiwavelength erbium-doped fiber ring laser incorporating an SOA-based phase Modulator. IEEE Photon-Technol. Lett.; 2005; 17, pp. 756-758. [DOI: https://dx.doi.org/10.1109/LPT.2005.843965]

20. Chen, D.; Ou, H.; Fu, H.; Qin, S.; Gao, S. Wavelength-spacing tunable multi-wavelength erbium-doped fiber laser incorporating a semiconductor optical amplifier. Laser Phys. Lett.; 2007; 4, pp. 287-290. [DOI: https://dx.doi.org/10.1002/lapl.200610109]

21. Zhang, Z.; Wu, J.; Xu, K.; Hong, X.; Lin, J. Tunable multiwavelength SOA fiber laser with ultra-narrow wavelength spacing based on nonlinear polarization rotation. Opt. Express; 2009; 17, pp. 17200-17205. [DOI: https://dx.doi.org/10.1364/OE.17.017200]

22. Im, J.E.; Kim, B.K.; Chung, Y. Stable SOA-based multi-wavelength fiber ring laser using Sagnac loop mirror incorporating a high-birefringence photonic crystal fiber. Laser Phys.; 2010; 20, pp. 1918-1922. [DOI: https://dx.doi.org/10.1134/S1054660X10190084]

23. Yan, N.; Silvira, T.; Teixeira, A.; Ferreira, A.; Tangdingga, E.; Monteriro, P.; Koonen, M.J. 40 Gb/s All-Optical Mul-ti-Wavelength Conversion via a Single SOA-MZI for WDM wavelength Multicast. Proceedings of the 12th Optoelectronics and Communication Conference on Integrated Optics and Optical Fibre Communication (OECC/IOOC 2007); Pacifico Yokohama, 9–13 July 2007; [DOI: https://dx.doi.org/10.34385/proc.49.13A1-3]

24. Sulaiman, A.H.; Yusoff, N.; Abdullah, F.; Mahdi, M.A. Tunable multiwavelength fiber laser based on bidirectional SOA in conjunction with Sagnac loop mirror interferometer. Results Phys.; 2020; 18, 103301. [DOI: https://dx.doi.org/10.1016/j.rinp.2020.103301]

25. Lo, H.-K.; Curty, M.; Tamaki, K. Secure quantum key distribution. Nat. Photon.; 2014; 8, pp. 595-604. [DOI: https://dx.doi.org/10.1038/nphoton.2014.149]

26. Yin, H.-L.; Fu, Y.; Li, C.-L.; Weng, C.-X.; Li, B.-H.; Gu, J.; Lu, Y.-S.; Huang, S.; Chen, Z.-B. Experimental quantum secure network with digital signatures and encryption. Natl. Sci. Rev.; 2023; 10, nwac228. [DOI: https://dx.doi.org/10.1093/nsr/nwac228] [PubMed: https://www.ncbi.nlm.nih.gov/pubmed/37168101]

27. Riggs, B.; Partridge, M.; Cambou, B.; Burke, I.; Rios, M.A.; Heynssens, J.; Ghanaimiandoab, D. Multi-Wavelength Quantum Key Distribution Emulation with Physical Unclonable Function. Cryptography; 2022; 6, 36. [DOI: https://dx.doi.org/10.3390/cryptography6030036]